Jump to content

Atari 5200 Power Supply Circuit Repair

From RetroTechCollection
Atari 5200 four-port motherboard power switch circuit (A26, S2, Q6 to Q10)
The power switching area of a four-port board with A designators: the MJE210 transistors Q6 and Q7 at the top, the push-button S2, the 4013 flip-flop A26, Q8, Q9 and Q10, and the power LED (photo: Evan-Amos, public domain)

The Atari 5200 has no mechanical on/off switch in its supply line. The power button S2 is a momentary push-button that toggles a 4013 flip-flop, U29 on the original four-port board CA018087 and A26 on the four-port "universal" board CA020108 and the two-port board CA021374. The flip-flop drives transistors Q9 and Q8, which switch the MJE-210 power transistor Q7 and the regulator VR2 that feeds the console's +5 V sources and the power LED.[1][2][3] When any part of this chain fails the console gives a snowy screen with no modulation, and if the fault is ahead of VR2 the LED stays dark. Atari's field service manual has a separate snowy-screen chart for each type of console; the steps below follow them.[2][4]

Four-port consoles take their power through the CX522 switchbox and the RF cable from the CX521 adaptor (Atari C018187, 9.3 V DC at 1.95 A). The two-port console has its own jack for the CA021673 adaptor and uses an ordinary manual switchbox.[1][5][6]

Atari 5200 schematic, power supply and power switch latch
The power supply on Atari's schematic sheet 2: Q6 with VR1, Q7 with VR2 and the LED, the cartridge jumper J1-36 to J1-18, and at lower right the 4013 latch U29a and U29b, the power switch, Q8, Q9 and Q10

How the circuit works

[edit | edit source]

From Atari's schematic sheet 2 (February 1983):[1]

  • The power switch feeds the S (pin 6) and RST (pin 4) inputs of the first half of the 4013, U29a, each pulled down by 22 kΩ. U29a's Q output (pin 1) clocks the second half, U29b, at pin 11.
  • U29b's Q output (pin 13) drives Q9 (2N3904) through 1 kΩ. Q9 drives Q8 (2N3904), and Q8 pulls the base of the PNP power transistor Q7 (MJE-210), which passes the supply to VR2 (an LM340T5 on the schematic).
  • VR2's +5 V output supplies the +5 V sources 1, 2 and 3; the power LED is fed from source 1 through 150 Ω.
  • Q6 (MJE-210) and VR1 make the other +5 V supply. The base circuit of Q6 runs through a jumper inside the cartridge, between J1-36 and J1-18, so this supply needs a cartridge fitted.
  • Q10 (2N3904) drives U29b's reset input, pin 10.

Atari's parts list gives the regulators as 78M05 (C014348), mounted as a heatsink and regulator assembly, CA019069 on the original board and CA020161 on the universal board. The transistors are 2N3904 at Q8 to Q10 and MJE210 (C018094) at Q6 and Q7; U29 or A26 is a 4013B (C014334); S2 is C018093; the LED is C014776.[3]

Symptoms

[edit | edit source]
  • A snowy screen with no game picture. Atari's symptom checklists name VR2, U29 (A26) and the RF module on the four-port, and VR2, A26, the RF module, the jack and the cable on the two-port.[7]
  • The LED stays off when S2 is pressed, or the console will not stay on.[4]
  • A solid coloured or black screen with the LED on is a different fault: Atari's black-screen chart starts with VR1 and the clocks. See the Atari 5200 Troubleshooting Guide.[7]

Check the simple things first: a cartridge fitted, the CX522 switchbox in the right position, and on a four-port the CX521 adaptor and not one from the Atari home computers. Atari's Tech Tip 6 warns that the home computer adaptor damages both the adaptor and the switchbox.[6][1]

Safety

[edit | edit source]
  • The CX521 adaptor contains a mains transformer, a fuse, a bridge rectifier and a 3300 µF reservoir; the console itself works at low voltage.[1]
  • Atari's chart warns against shorting across C48 when testing it.[2]
  • Unplug the adaptor before removing or fitting a chip or transistor.

Tools and parts

[edit | edit source]
  • A multimeter, a known-good CX521 adaptor and CX522 switchbox (four-port) or CA021673 adaptor (two-port), and a game cartridge.[6][5]
  • Phillips screwdriver: five Phillips screws hold the case together.[8]
  • Replacement parts as listed above. Atari's charts name Q7, Q8, Q9, Q10, R55, R58, R61, C47, S2, the 4013, VR2 and L13.[2][9][10][4]

Procedure

[edit | edit source]

Opening the console

[edit | edit source]
  1. Unplug the adaptor and the RF cable. Remove the five Phillips screws that hold the top and bottom covers together and lift the top cover off. The hinged cover of the controller storage area comes away as a separate piece.[8]
  2. An aluminium shield covers the board.[8] The power switch, the 4013 and the transistors are at the right-hand end of the board in the photograph.[11]

Four-port consoles: Atari's chart

[edit | edit source]
Atari 5200 snowy screen power flowchart (FSM p. 4-9)
Atari's four-port snowy-screen chart, first page (field service manual p. 4-9)

Read U29 as A26 on a CA020108 board.[2]

  1. Measure the centre of the RF/power input J3. It should carry 10 to 12 V. If not, the RF cable, the switchbox or the adaptor is faulty.[2]
  2. Check C48, without shorting across it. Replace it if it is faulty.[2]
  3. Measure +5 V on pin 3 of the RF module. If it is present, the fault is L13, the RF module, or an open between RF module pin 2 and VCC2.[2]
  4. If pin 3 has no +5 V, measure the input of VR2. If +12 V is there, go to the regulator checks below.[2]
  5. If VR2 has no input, press S2 repeatedly and watch U29 pin 13. It should change between 13 V and 0 V at each press. If it does not, go to the latch checks below.[2]
  6. If pin 13 toggles, press S2 so that pin 13 is high. Q8's collector should be at 0 V; if not, Q8 or Q9 is faulty.[9]
  7. With Q8's collector at 0 V, Q7 should have 13 V on its base and 14 V on its emitter. If not, suspect Q7, R55, R58 or an open trace to Q8's collector. If the readings are right and VR2 still has no input, Q7 is faulty.[9]

Latch checks (pin 13 does not toggle)

[edit | edit source]
Atari 5200 power latch flowchart (FSM p. 4-11)
Atari's latch checks: U29 pins 11, 10, 6 and the link from pin 9 to pin 12 (field service manual p. 4-11)
  1. Press S2 repeatedly and watch U29 pin 11.[10]
  2. If pin 11 toggles, check U29 pin 10. If it is not at 0 V, replace Q10. If the console still does not work, look for an open trace or a faulty resistor or capacitor in the circuit.[10]
  3. If pin 10 is at 0 V, check continuity between U29 pins 9 and 12. Repair the trace if it is open; if it is good, replace U29.[10]
  4. If pin 11 does not toggle, watch U29 pin 6: it should go high while S2 is pressed and low when it is released. If it does, replace U29. If it does not, look for shorts or opens on that pin, or a faulty S2.[10]

Regulator checks (VR2 has its input)

[edit | edit source]
  1. Measure the output of VR2. If +5 V is present, the fault is an open from VR2 pin 3 to VCC2, +5B or +5F.[12]
  2. If VR2 pin 3 is shorted to ground, a chip may be shorted. Remove the chips one at a time and switch on after each; when the picture appears, the last chip removed is faulty. If no chip is shorted, look for a shorted capacitor or trace.[12]

Two-port consoles: Atari's chart

[edit | edit source]
  1. Is the LED on? If it is, measure +5 V on RF module pin 3. If it is missing, L13 is faulty or pin 3 is open to VR2; if it is present, check that RF module pin 1 is grounded. With both correct, the RF module, the RF cable or J3 is faulty.[4][13]
  2. If the LED is off, measure +5 V at the output of VR2 or pin 3 of the RF modulator. If it is present, the LED or its connection from VR2 is open.[4]
  3. If there is no +5 V, measure the input of VR2: it should be at least +7 V. If it is, VR2 is faulty or its output is shorted.[4]
  4. If VR2 has no input, measure Q7: its base should be 0.7 to 1.0 V below its emitter. If it is, Q7 is faulty.[4]
  5. If not, check Q8's collector. If it is at 0 V, R58 is faulty or the trace to Q7 is broken.[4]
  6. If Q8's collector is not at 0 V, measure Q8's base. If it is at 0.7 to 1.0 V, Q8 is faulty.[14]
  7. If not, measure Q9's base. If it is at 9 to 15 V, Q9 is faulty.[14]
  8. If not, press S2 and watch A26 pin 11. If it changes state, A26 is faulty. If it does not, check S2, C47, Q10 and R61, and check for 9 to 15 V at A26 pin 14.[14]

Replacing parts

[edit | edit source]
  • Atari's "swapout" rule for chips: fit known-good parts one at a time, leave each in place, and once the console works refit the originals one by one to find which were faulty.[15]
  • VR1 and VR2 are supplied with their heatsink as an assembly; Atari's parts list gives the regulator inside as a 78M05.[3] The Atari 5200 General Maintenance page covers refitting a regulator to its heatsink.

Testing

[edit | edit source]
  • Press S2: the LED should light and the console should start. Press it again and the console should switch off.[2][1]
  • With a cartridge fitted and the console on, VR2's output should be +5 V and RF module pin 3 should carry +5 V.[2][12]
  • Atari's charts end at "F", a return to the start of the diagnostic cartridge test sequence; run the full diagnostic cartridge tests before closing the console.[15]

Board variations

[edit | edit source]
  • CA018087 uses U designators (the latch is U29); CA020108 and CA021374 use A designators (A26).[2]
  • R57 and R58 are 330 Ω 1 W metal film resistors on CA018087 and CA021374, and 182 Ω 1 W on CA020108.[3]
  • The two-port board takes its power through a jack on the console, not through the switchbox and RF cable.[5]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 Atari, Inc., Atari 5200 Programmable Video Game System schematic, sheet 2 of 2 (RF switchbox, modulator and power supply), 23 February 1983. See File:Schematic Atari5200 RFSwitchbox 2000.png.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen Troubleshooting", p. 4-9.
  3. ↑ 3.0 3.1 3.2 3.3 Atari, CX5200 Field Service Manual FD100127 Rev. 4, section 8, parts lists for CA018087, CA020108 and CA021374 (pp. 8-1 to 8-9): VR1 and VR2, the heatsink assemblies, Q6 to Q10, U29 and A26, S2, DS1, R57 and R58.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen (Power Supply) Troubleshooting", two-port, p. 4A-10.
  5. ↑ 5.0 5.1 5.2 Atari, Inc., CX5200 Field Service Manual, FD100127 Rev. 4, July 1983, section 1, pp. 1-1 and 1-2: the three boards, and the two-port's adaptor jack and manual switchbox. Hosted here as Atari CX5200 Field Service Manual.
  6. ↑ 6.0 6.1 6.2 Atari, Inc., Tech Tip 6, "CX5200 Power Adaptor", 17 November 1982, in Atari 2600 and Atari 5200 Field Change Orders, Upgrade Bulletins, Tech Tips. Hosted here as Atari 2600 and 5200 Field Change Orders and Tech Tips.
  7. ↑ 7.0 7.1 Atari, CX5200 Field Service Manual FD100127 Rev. 4, sections 5 and 5A, symptom checklists, pp. 5-1 and 5A-1.
  8. ↑ 8.0 8.1 8.2 Atari, CX5200 Field Service Manual FD100127 Rev. 4, p. 1-3: outer case (five Phillips-head screws), top cover and RF shield.
  9. ↑ 9.0 9.1 9.2 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen Troubleshooting (cont.)", p. 4-10: Q8, Q9, Q7, R55 and R58.
  10. ↑ 10.0 10.1 10.2 10.3 10.4 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen Troubleshooting (cont.)", p. 4-11: U29 (A26) pins 11, 10, 6, 9 and 12, Q10 and S2.
  11. ↑ Evan-Amos, photograph of an Atari 5200 four-port motherboard, Wikimedia Commons, public domain: File:Atari-5200-4-Port-Motherboard-Flat.jpg.
  12. ↑ 12.0 12.1 12.2 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen Troubleshooting (cont.)", p. 4-12: VR2 output and shorted chips.
  13. ↑ Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen (Power Supply) Troubleshooting (Continued)", two-port, p. 4A-11.
  14. ↑ 14.0 14.1 14.2 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Snowy Screen (Power Supply) Troubleshooting (Continued)", two-port, p. 4A-12.
  15. ↑ 15.0 15.1 Atari, CX5200 Field Service Manual FD100127 Rev. 4, p. 4-1: how to use the flowcharts, the swapout procedure and the meaning of F.