Jump to content

Atari 520ST MIDI Port Repair

From RetroTechCollection
Rear ports of original Atari 520ST
The back panel of a short-case ST. MIDI OUT and MIDI IN are the two five-pin DIN sockets to the right of the power socket (photo: Blake Patterson, CC BY 2.0).

The Atari 520ST has MIDI built in: a second MC6850 ACIA, U20, runs the 31.25 kbaud current loop, with MIDI IN on J7 and MIDI OUT on J8. The output passes through two inverters to the socket; the input is isolated by a PC-900 opto-coupler, U39; and the MIDI OUT socket also carries a THRU copy of the input on its spare pins.[1][2] The 260ST, 520ST+ and 520STM have the same circuit on the same short-case board.[3]

Atari's checklist for MIDI faults names the opto-isolator, the 6850 and the inverter; Howard W. Sams's service data gives a test for each direction.[2][4]

Symptoms

[edit | edit source]
  • Instruments connected to MIDI OUT receive nothing.[4]
  • The computer does not respond to a keyboard or other device on MIDI IN.[4]
  • MIDI IN works but nothing comes out of the THRU contacts on MIDI OUT.[4]
  • Diagnostic cartridge errors: M0, no data received through the loop-back cable; M1, data mismatch (replace the 6850); M2 and M3, framing and parity errors from a bad 6850 or a noisy driver or receiver.[2]

Try another MIDI cable and device before opening the computer.

Tools and parts

[edit | edit source]
  • An oscilloscope or logic probe.
  • A TTL function generator for the input test, set to a 5 V, 5 kHz square wave.[4]
  • ST BASIC, for the output test.[4]
  • Atari's diagnostic cartridge and MIDI loop-back cable, if available.[2]
  • Parts from the schematic: MC6850 (U20), 74LS04 (U35), 74LS05 (U36), PC-900 opto-coupler (U39), 1N914 (CR7), 220 Ω resistors (R76–R80) and 4.7 kΩ (R81).[1]
Atari 520ST MIDI ports (schematic C070231 sheet 1)
The MIDI ports on Atari's 520ST schematic: the output through U35 and U36 to J8 at the top, the THRU path below it, and the input through R76 and the opto-coupler U39 from J7 at the bottom.
Signal paths (schematic C070231)
Path From Through To
MIDI OUT U20 transmit data (pin 6) U35 pins 1→2, U36 pins 5→6, R79 220 Ω J8 pin 5; pin 4 to +5 V through R78 220 Ω
MIDI IN J7 pin 4 (+) and pin 5 R76 220 Ω, U39 LED (pins 1 and 2), CR7 across it U39 output, pulled up by R81 4.7 kΩ, to U20 receive data (pin 2)
MIDI THRU U39 output U35 pins 3→4, U36 pins 9→8, R80 220 Ω J8 pin 3; pin 1 to +5 V through R77 220 Ω

Sources: the schematic,[1] with the ACIA pin numbers from SAMS.[4]

Procedure

[edit | edit source]

Open the machine

[edit | edit source]

Atari's sequence for the short case:[2]

  1. Unplug the supply. Turn the computer over and remove the six screws from the bottom case.
  2. Turn it upright, lift off the top case and unplug the keyboard at the right front of the board.
  3. Remove the three screws at the front edge of the board and the three at the rear, reached through holes in the shield, and lift the board assembly out.
  4. Straighten the ten twist tabs and lift off the top shield. Reconnect the keyboard, supply and monitor to work on the board.

MIDI OUT

[edit | edit source]
  1. Load ST BASIC and run SAMS's line, which sends data to the MIDI port continuously:[4]
10 OUT 3,100: GOTO 10
  1. Check for pulses at J8 pin 5. If they are there, check the socket's joints and the cable.[4]
  2. If not, check for pulses at U36 pin 5. If they are present there, U36 is faulty.[4]
  3. If they are missing at U36 pin 5, check U20 pin 6. Pulses at U20 pin 6 point at U35; none there point at U20.[4]
  4. Check R79 and R78 with the power off.[1]

MIDI IN

[edit | edit source]
  1. Connect the function generator's TTL output, 5 V at 5 kHz, to J7: the high side to pin 4 and the low side to pin 5.[4]
  2. Check for pulses at U39 pin 1. If they are missing, check R76, CR7 and the socket J7.[4]
  3. If they are present, check U20 pin 2. Pulses missing there point at the opto-coupler U39; pulses present there point at U20.[4]

MIDI THRU

[edit | edit source]
  1. With the input signal still applied and reaching U20 pin 2, check for it at J8 pin 3.[4]
  2. If it is missing, check U35 pin 4. Missing there points at U35; present there points at U36.[4]

Reassemble

[edit | edit source]

Refit the top shield and its tabs, the board and its six screws, the keyboard and the top case, with the longer case screws at the rear.[2]

Testing

[edit | edit source]
  • Connect a MIDI OUT to MIDI IN cable and run the diagnostic cartridge's MIDI test, which sends data out, reads it back and checks the 6850's interrupt through the MFP.[2]
  • Play a MIDI keyboard into the ST with a sequencer, and play back to an instrument.
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 Atari (Japan) Corporation, Schematic Diagram (520ST/260ST), drawing C070231, revision M (April 1986), sheet 1: the ACIA U20, U35 (74LS04), U36 (74LS05), the opto-coupler U39 (PC-900), R76–R81, CR7, C59 and the sockets J7 and J8. Hosted here: File:Atari 520ST Schematic C070231.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Atari Corporation, 520ST/1040ST Computer Field Service Manual, C026118-002 Rev B (3.6), January 1987. MIDI interface description, 31.25 kbaud current loop and MIDI OUT carrying MIDI THRU (PDF p. 19); MIDI test and error codes M0–M3 (printed p. 3.9, PDF p. 35); symptom checklist, MIDI (PDF p. 51); 520ST disassembly (pp. 4.3–4.4, PDF pp. 48–49). Hosted here: File:Atari 520ST and 1040ST Computer Field Service Manual.pdf.
  3. ↑ "Atari 520ST, 260ST, 520ST+, 520STM, 130ST und ST Junior", atari-computermuseum.de (in German), revised 26 June 2024: the short-case models and their common main board, C070243.
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 SAMS Computerfacts CSCS12: Atari Model 520ST, Howard W. Sams & Co., June 1986, ISBN 0-672-08974-2. Troubleshooting, "MIDI ports": the output test program and the input test with a function generator (printed p. 28, PDF p. 30). Internet Archive.