Jump to content

Atari 600XL RAM Replacement

From RetroTechCollection
Atari 600XL board layout, RAM and custom chip area (FD100610 figure 6-1)
Atari's silkscreen drawing of the 600XL board: the two RAM chips U11 and U12 at the top right, U18 at the left of the middle row, and ANTIC (U9) and the CPU (U10) along the bottom

The Atari 600XL holds its 16 KB of RAM in two 16K × 4 dynamic RAMs, U11 and U12 (Atari part C061505), each in an 18-pin socket.[1] U11 holds data bits D0 to D3 and U12 holds D4 to D7.[1] Atari's field service manual widens a RAM failure beyond the two chips to the address decoder, MMU, multiplexers and memory timing logic, and it names two faults that make a good 600XL fail its RAM test: a 74LS32 fitted at U18 where a 74S32 is required, and the wrong revision of ANTIC.[1] Because every IC on the board is socketed, most of the checks are chip swaps.[1]

Symptoms

[edit | edit source]
  • Red blocks in the self test's memory test.[1]
  • A green or yellow screen at switch-on; Atari's checklist gives U1 to U7 and U11 to U16 as the causes.[1]
  • "RAM test failed" in Atari's Super SALT diagnostics, or one of its RAM-related fatal system error codes, 04 to 11, 17 or 18.[1]
  • Programs that turn the screen off fail. Atari's Tech Tip 20 traces this, and Super SALT RAM test failures, on early machines to the wrong ANTIC.[1]

Safety

[edit | edit source]
  • Check the 5 V supply first; Atari specifies +5 V ±2 % at up to 1.5 A.[1] See Atari 600XL Troubleshooting Guide for the supply checks.
  • Switch off before pulling or fitting any chip, and fit each one the right way round.

Tools and parts

[edit | edit source]
  • An IC extraction tool.
  • Replacement 16K × 4 DRAMs (18-pin) for U11 and U12 (Atari C061505).[1]
  • A 74S32 for U18 (Atari C061622).[1]
  • An ANTIC of the correct type for U9: C021697 (Rev. E) in a domestic (NTSC) machine, C021698 in an international (PAL) machine.[1]
  • Optionally, Atari's Super SALT cartridge and extended hardware (kit FK100331).[1]

Procedure

[edit | edit source]

Open the machine

[edit | edit source]
  1. Turn the computer upside down and remove the four screws from the bottom cover.[1]
  2. Turn it upright and tip the cover by raising its left side. Remove the keyboard cable from its socket and set the top aside.[1]
  3. The chips can be reached once the RF shield is off. To remove the board, take out the screw reached through the RF shield at the top left (a magnetic screwdriver helps), then the four remaining screws; the shield is held together by six bolts and nuts.[1]

Run the memory test

[edit | edit source]
  1. Remove any cartridge. Hold OPTION while switching on until the self test menu appears.[1]
  2. Select MEMORY with SELECT and start it with START. Two long bars represent the two 8K ROMs and the row of sixteen blocks below them the RAM, one block per kilobyte. A block under test is white, turns light green if good and red if bad, and a failed block is not tested again.[1]
  3. Do not leave a self test screen on for more than about seven minutes; it does not go into attract mode and can burn the screen.[1]

With Super SALT, the RAM test blanks the screen for up to 24 seconds while it tests refresh, then shows an error summary in which failed data bits are marked with an inverse-video F. A failure on D0 to D3 is U11 and on D4 to D7 is U12, wherever the address, unless the fault is in the support logic.[1]

Check U18 and ANTIC first

[edit | edit source]
Atari 600XL RAM U11 U12 and memory support logic (FD100610 schematic)
Atari's schematic of the 600XL memory: U11 and U12 (16K × 4) with the multiplexers U5 and U6, the delay line U13 and the gates U14, U15, U16 and U18 that time the RAM strobes
  1. Read the marking on U18. Atari's checklist says to verify that it is a 74S32; its footnote reads "MUST have correct IC's or RAM will fail".[1] Replace a 74LS32 with a 74S32.
  2. Read the part number on ANTIC, U9. Tech Tip 20 (17 August 1983) reports that "the first 24 K International and possibly some of the Domestic 600 XL units" were built with the wrong ANTIC; the correct part is C021698 for international machines and C021697 for domestic ones. Fit the correct part if it is wrong.[1]
  3. Run the memory test again.

Replace the RAM

[edit | edit source]
  1. If a block still fails, replace the RAM chip that the Super SALT summary points to, or swap U11 and U12 for known-good parts one at a time.[1]
  2. If the test still fails with good RAM, Atari's next step is ANTIC and then the support logic: the checklist lists U1, U2, U5 to U7, U11 to U16 and U18 for a failed RAM test.[1] Swap each socketed chip for a known-good one in turn, switching off for every swap.
Chips Atari lists for a failed 600XL RAM test
Position Part (Atari number) Role
U1 74LS138 decoder (C061428) Address decoding
U2 MMU (C061618) Memory management
U5, U6 74LS158 multiplexers (C014345) RAM address multiplexing
U7 74LS08 (C017097) Logic
U11, U12 16K × 4 DRAM (C061505) RAM, D0-D3 and D4-D7
U13 Delay module (C060472) RAM timing
U14 74LS14 (C061850) Logic
U15 74LS375 latch (C060613) Logic
U16 74LS51 (C060474) Logic
U18 74S32 (C061622) Must be the S-series part

[1]

Reassemble

[edit | edit source]

Refit the RF shield and the board, reconnect the keyboard cable and refit the top with its four screws.[1]

Testing

[edit | edit source]
  1. Run the self test's memory test: all sixteen blocks and both ROM bars should turn green.[1]
  2. Run a program that turns the screen off, or Super SALT's RAM test, to confirm that the ANTIC fault in Tech Tip 20 is not present.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 Atari, Inc., ATARI 600XL Computer Field Service Manual, FD100610 Rev. 1, October 1983: power supply p. 1-10; self test pp. 2-1 to 2-3; Super SALT RAM test p. 2-17 and fatal system error codes p. 2-31; symptom checklist pp. 3-1 to 3-2 ("Green/Yellow Screen", "RAM Test Failed" and its footnote); disassembly p. 4-1; schematic and silkscreen (section 5); parts list pp. 5-5 to 5-7 (U11-12 C061505, U18 74S32 C061622, U9 ANTIC Rev. E C021697, sockets for every IC); Tech Tip 20, 17 August 1983 (section 6). Hosted here as Atari 600XL Field Service Manual.