Jump to content

Atari 65XE RAM Replacement

From RetroTechCollection
Atari65XE Mainboard
A 65XE board, C070025 Rev. C, in its lower case. The eight RAM chips run down the left-hand edge, U16 at the top, soldered directly to the board

The Atari 65XE holds its 64 KB of RAM in one of two ways. The C070025 and CA20097 boards use eight 64K × 1 dynamic RAMs (4164) at U9 to U16; the cost-reduced CA200519 board uses two 64K × 4 chips (4464) at U9 and U10.[1] The same guide applies to the Atari 800XE, the PAL 65XE with the expansion port, which the reproduction documents on the CA200519 board, and to the PAL 65XEs sold in Poland (Atari 65XE (Poland)).[1][2] A failed chip shows as red blocks in the self test's memory test or in Atari's production RAM test, or stops the machine starting. Retrohax, repairing a batch of thirty-two 65XEs, found that the boards in his first group of ten or eleven that were quick to fix each had a failed RAM chip or a failed CPU.[3]

Symptoms

[edit | edit source]
  • Red blocks in the self test's memory test. Hold OPTION while switching on, with no cartridge and no powered disk drive, to reach the self test.[2]
  • A RAM failure, or error codes 04, 05, 07, 08 or 10, from Atari's XE/XL production test cartridge, which identifies the machine as "ATARI 65XE TESTS".[4]
  • A black screen at switch-on. Check the supply and clocks first; the procedure is in Atari 130XE Black Screen Repair, whose chip pins apply to the same custom chips.

Safety

[edit | edit source]
  • Check the 5 V supply before replacing RAM. The FAQ warns that the sealed "Ingot" version of Atari's 1.5 A supply can damage the computer if it fails and is not switched off quickly.[2]
  • Switch off before fitting or removing any chip.

Tools and parts

[edit | edit source]
  • For the C070025 and CA20097 boards: 4164-type 64K × 1 DRAMs, 16-pin DIP, and 16-pin sockets.[1][5]
  • For the CA200519 board: 4464-type 64K × 4 DRAMs, 18-pin DIP, and 18-pin sockets.[1]
  • A desoldering station or pump and a logic probe.
  • Optionally, Atari's XE/XL production test cartridge with its loop-back plugs.[4]

Procedure

[edit | edit source]

Identify the board

[edit | edit source]
  1. Open the case as described in Atari 65XE General Maintenance#Opening the machine and remove the shield.
  2. Read the assembly number printed on the board and count the RAM chips: eight 16-pin chips on C070025 and CA20097, two 18-pin chips on CA200519.[1] The board in the photograph is marked C070025 Rev. C.

Find the failing chip on an eight-chip board

[edit | edit source]
Atari 65XE DRAM U9-U16 data bits (Sobola schematic)
Jerzy Sobola's schematic of the eight-chip RAM: U9 carries D0 and U16 D7, each through a 100 Ω resistor (R138 to R145) with a 10 kΩ pull-up (R30 to R23)
  1. Run the production test's RAM test if the cartridge is available. On an error it halts and shows the test number (1 to 4), the failing address, the data read, the data expected, and bits 1 to 8, one per RAM chip, red for a bad bit and green for a good one.[4] Compare the data read with the data expected to find the bit that differs.
  2. Turn the bit into a chip using the schematic: U9 is D0, U10 D1, and so on to U16, D7.[5]
  3. On this board each chip's data pins (14 and 2) reach the data bus through a 100 Ω resistor, R138 (D0) to R145 (D7), with a 10 kΩ pull-up to +5A, R30 (D0) to R23 (D7).[5] Before condemning a chip, check its resistor for an open circuit.
  4. Without the cartridge, the piggyback test described in Atari 800XL RAM Replacement can be tried on these 4164-type chips: with a known-good chip pressed on top of a suspect, the memory test may pass when it sits on the failed one.
Eight-chip boards: data bit, chip and resistors (Sobola schematic)
Data bit D0 D1 D2 D3 D4 D5 D6 D7
Chip U9 U10 U11 U12 U13 U14 U15 U16
Series resistor (100 Ω) R138 R139 R140 R141 R142 R143 R144 R145
Pull-up (10 kΩ) R30 R29 R28 R27 R26 R25 R24 R23

[5]

Find the failing chip on a CA200519 board

[edit | edit source]
Atari 65XE 800XE CA200519 board 4464 RAM U9 U10 (130XE FSM reproduction)
The two 64K × 4 RAMs on the CA200519 board: U9 carries D0 to D3 and U10 D4 to D7
  1. On the CA200519 board U9 holds data bits D0 to D3 (pins 2, 3, 15 and 17) and U10 holds D4 to D7. Pin 9 is +5A and pin 18 ground, decoupled by C34 and C35.[1]
  2. A bad bit from the production test therefore points to U9 if it is one of D0 to D3 and to U10 if it is one of D4 to D7.[1][4]
  3. A 16-pin chip cannot be piggybacked on an 18-pin 64K × 4 part.[6]

Replace the chip

[edit | edit source]
  1. Check the supply at the suspect chip first: pin 8 is +5 V and pin 16 ground on a 4164, as on Atari's schematic of the 130XE, which uses the same chips; pin 9 is +5 V and pin 18 ground on a 4464.[7][1]
  2. Desolder the failed chip and clear each hole. On the board in the photograph the RAM is soldered directly to the board.
  3. Fit a socket, notch matching the original chip, and fit the new chip.
  4. Refit the shield and the board, reconnect the keyboard and close the case.

Testing

[edit | edit source]
  1. Run the self test's memory test: every block should turn green.[2]
  2. If the production test cartridge is available, its RAM test should report PASS after about 15 seconds.[4]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 130XE Personal Computer Field Service Manual, reproduction by JER/Eightbitter (PDF author "Jurek"), November 2016, with schematics redrawn in 2014: section 2, figures 2-7 (65XE 8 × 4164 assembly C070025), 2-9 (65XE 8 × 4164 assembly CA20097) and 2-11 (65XE/800XE 2 × 4464 assembly CA200519: U9 D0-D3, U10 D4-D7, C34, C35). Not an Atari publication. Hosted here as Atari 130XE Field Service Manual.
  2. ↑ 2.0 2.1 2.2 2.3 Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009, sections 1.7 (65XE versions and boot options), 1.9 (800XE) and 6.7 (power supplies). faqs.org. Community reference.
  3. ↑ drygol, "The mass Atari 65XE fixing frenzy", retrohax.net, 2 May 2020.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 Atari Corp., XE/XL Production Test Operator's Instructions and Diagnostic Error Codes, Rev. 3.4, 22 May 1986 (the 65XE identification, the RAM test display, error codes 04 to 10). In Atari 130XE Parts List and Production Test Instructions.
  5. ↑ 5.0 5.1 5.2 5.3 Jerzy Sobola, Atari 65XE schematic, nine sheets, 23 September 2003: sheet 4 (U9-U16 4164, data lines, R23-R30, R138-R145). Community redrawing of the eight-chip board. Hosted here as File:ATARI65XE-SCHEMATIC.pdf.
  6. ↑ Terry Stewart (tezza) and others, "4264 DRAM compatible with 4164?", Vintage Computer Federation Forums, April 2010: 64K × 4 parts have 18 pins and cannot take a piggybacked 4164.
  7. ↑ Atari Corp., 130XE Reference Manual (cover dated March 1990), schematic diagram C070065 Rev. B (4164 DRAM pins 8 and 16). Hosted here as Atari 130XE Parts List and Production Test Instructions.