Jump to content

Atari 1025 Space Belt Replacement

From RetroTechCollection
Atari 1025 base unit exploded view (field service manual figure 4-4)
Atari's figure 4-4, the 1025 base unit: the space motor (with its pulley, 18, and mounting screws, 19) sits on the base plate behind the platen

The Atari 1025 Printer moves its print head carriage with a toothed space belt driven by the space motor. The same belt turns the ribbon drive gear, which is why the ribbon gears come off before the belt can be changed.[1] Atari's 1025 Printer Field Service Manual gives the procedure for replacing the belt and the two adjustments that must follow it: belt tension and the first character printing position. The same adjustments follow a space motor replacement.[1]

Symptoms

[edit | edit source]
  • The carriage does not travel across the paper, or does not travel freely. Atari's carriage flowchart starts by trying to move the carriage by hand.[1]
  • After belt or motor work, the print head does not line up for the first character of a line.[1]

Rule out the drive electronics first. Sams' check for a carriage that does not move: switch off, move the carriage to the right and switch on; it should return to the home position. If it does not, check for 26 V at pins 5 and 6 of connector CN4, and for the 7.37 MHz clock at pins 18 and 19 of the CPU, Q8; then check the carriage motor windings, the CPU and the board.[2] Atari's symptom checklist lists the print head, space motor, Q5, Q4 and the transistor array TRA1 for a carriage that does not move. See the Atari 1025 Troubleshooting guide.[1]

Safety

[edit | edit source]

The 1025 has its mains transformer and fuse inside the case. Unplug it from the wall before opening it, and disconnect the mains plug before removing or refitting any connector.[1]

Tools and parts

[edit | edit source]
  • A No. 2 Phillips screwdriver.[1]
  • A 300 g stick pressure gauge for the belt tension.[1]
  • A way to remove and refit the small E-snap rings on the ribbon gears and ribbon change lever.[1]
Parts involved (FD100290 parts list, pp. 7-1 and 7-2)
Figure and callout Part Atari part number
4-6, N Belt, ribbon/carriage drive, space FC100428
4-4, 18 Space motor (carriage) FC100438
4-4, I Idle pulley bracket (clinched) FC100440
4-3, 15 Belt clamp FC100436
4-6, 28 Ribbon drive gear FC100424
4-6, 26 Detent spring FC100426
4-6, 42 E-snap ring FC100430
4-6, 20 E-snap ring FC100431

[1]

Procedure

[edit | edit source]

Opening the printer

[edit | edit source]
  1. Remove the platen knob.[1]
  2. Pull the top cover straight up.[1]
  3. Loosen the two switch assembly screws and slide the switch back out of the way of the cover.[1]
  4. Remove the two upper cover screws from inside the front of the upper cover.[1]
  5. Tip the upper cover back to free it from the hooks on the lower cover, and lift it off.[1]

Removing the belt

[edit | edit source]
Atari 1025 ribbon assembly exploded view (field service manual figure 4-6)
Atari's figure 4-6, the ribbon assembly: the spool gear parts (20 to 25), the detent spring (26), the ribbon change lever (27) with its E-rings (41, 42) and the ribbon drive gear (28) that meshes with the space belt

The numbers are the callouts in Atari's exploded figures 4-3, 4-4 and 4-6.[1]

  1. Loosen the space motor's mounting screws (19) and move the motor to slacken the belt.[1]
  2. Remove the space belt clamp screw (14) and the belt clamp (15) from the carriage assembly.[1]
  3. Take out the ribbon and set it aside.[1]
  4. Remove the E-snap ring (20) from one of the ribbon spool gears and lift off that gear assembly (21 to 25).[1]
  5. Remove the detent spring (26).[1]
  6. Remove the E-snap rings (41 and 42) on the ribbon change lever (27), then the lever and the ribbon drive gear (28).[1]
  7. Remove the old belt and fit the new one.[1]

Refitting

[edit | edit source]
  1. Put the ribbon drive gear (28) back into the ribbon change lever (27). Engage the gear's pulley teeth accurately with the teeth of the space belt before fitting the lever's E-snap rings.[1]
  2. Refit the detent spring (26).[1]
  3. Reassemble the ribbon spool gear assembly (20 to 25).[1]
  4. Refit the belt clamp (15) to the carriage with its screw (14).[1]
  5. Set the belt tension and then the first character position, as below.[1]

Setting the belt tension

[edit | edit source]
Atari 1025 space belt tension adjustment (field service manual figure 4-5)
Atari's figure 4-5: the belt is pressed in 5 mm with the stick gauge beside the ribbon bracket, and the idle pulley bracket is moved to set the tension
  1. Move the idle pulley bracket one way or the other until the tension is between 80 and 140 g when the belt is pressed in 5 mm at the point shown in figure 4-5, measured with the 300 g stick gauge.[1]

The text of the manual gives 80 to 140 g; the label on figure 4-5 reads 80-120 g.[1]

Setting the first character position

[edit | edit source]
Atari 1025 first character printing position (field service manual figure 4-9)
Atari's figure 4-9: the carriage's detector lever at the home sensor, 0.55-0.75 mm and about 1 mm clearances
  1. Loosen the space motor mounting screws.[1][2]
  2. Move the motor a little one way or the other so that when the printer is switched on, the print head returns and stops at the home sensor position shown in figure 4-9.[1][2]
  3. Tighten the motor screws again and check the position by switching off and on.[2]
  4. If moving the motor does not bring the head to the right position, move the belt one or two teeth round the pulley and repeat.[1][2]

Reassembly

[edit | edit source]
  1. Refit the ribbon.[1]
  2. Refit the upper cover, switch assembly and top cover in the reverse order of removal, and push the platen knob back on.[1]

Testing

[edit | edit source]
  1. Switch on with paper loaded. The carriage should return to the home position.[2]
  2. Run the ROM self test: with the printer off and the I/O cable disconnected, move the shorting plug SP1 at the left corner of the board from position A to position B, load paper and switch on with the PRINT switch on. The self test prints the standard character set at 10 characters per inch and 80 columns.[1]
  3. Check that the first character of each line lines up and that the ribbon moves as the carriage travels.[1]
  4. Switch off and move SP1 back to position A.
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 Atari, Inc., 1025 Printer Field Service Manual, FD100290 Rev. 01, June 1983: ROM self test p. 3-7; parts list pp. 7-1 and 7-2 (PDF pp. 73 and 74); upper cover disassembly p. 4-1; space motor replacement p. 4-3; space belt tension adjustment with figure 4-5, and space belt replacement, pp. 4-4 and 4-5; first character printing position adjustment p. 4-8 and figure 4-9 p. 4-9 (PDF pp. 31-39); exploded figures 4-3, 4-4 and 4-6, pp. 4-15, 4-17 and 4-19 (PDF pp. 45, 47 and 49); carriage flowchart, section 5; symptom checklist p. 6-1; maintenance precautions. Hosted here as File:Atari 1025 Printer Field Service Manual FD100290 Rev 01.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 Howard W. Sams & Co., Sams Computerfacts CP21, Atari Model 1025 (1986): first character printing position adjustment (PDF p. 4) and the "Printer carriage assembly does not move" service checks (PDF p. 5). Hosted here as File:Sams Computerfacts CP21 Atari 1025 Printer.pdf.