Atari 1040STE Video Ghosting Repair

The Atari 1040STE and Atari 520STE can show faint "ghost" images on an RGB monitor or SCART television: a pale copy trailing to the right of bright objects and at the ends of lines. exxos traced it to the supply of the STE's colour output transistors and lists the fix among his recommended fixes for every STE; he notes that the Mega STE shows the same fault.[1][2]
On Atari's schematic the three colour buffers, Q400, Q401 and Q402, take their collector supply from VCC through the ferrite L401, decoupled only by C411, a 0.47 µF capacitor. exxos's fix is to add a large low-ESR capacitor across C411.[3][1]
Symptoms
[edit | edit source]- A faint copy of bright objects to their right, most visible on a light background and at the ends of black lines, on RGB or SCART.[1]
exxos tested the fix only on RGB and SCART, not on the RF or composite outputs.[1] Ghosting can also come from a bad video cable or a poor LCD television, and a failing power supply makes the STE's video worse in general, so check those first; see the Atari STE Troubleshooting Guide.[1]
Tools and parts
[edit | edit source]- A 47 µF low-ESR electrolytic capacitor. exxos gives the Panasonic ECA-1CM470 (47 µF 16 V) as an example and warns that ordinary capacitors will not work.[1]
- Optionally, a 1 µF ceramic capacitor (exxos's example: Multicomp MCMLR50V105MY5V).[1]
- For the optional noise reduction below, three 47 pF ceramic capacitors.[1]
- Soldering iron and solder.

Procedure
[edit | edit source]Open the machine
[edit | edit source]Atari's sequence for the STE:[4]
- Unplug the machine. Turn it upside down and remove the six screws in the square holes and the three in the round holes.
- Turn it upright, lift off the top case, unplug the keyboard harness at the right front corner, and unplug and lift out the disk drive.
- Remove the screw on the right of the power supply shield and the three screws between the back-panel shield and the supply shield, straighten the two twist tabs, lift the supply shield off, and remove the two screws at the supply's front corners.
- Remove the three screws at the front of the board assembly, lift it at the front and pull it forward.
- Straighten the upper shield's twist tabs (usually four), remove any copper tape and lift the shield off.
Add capacitance across C411
[edit | edit source]
- Find C411, near the top left of the SIMM sockets in exxos's photograph, beside the ferrite L401.[1][3]
- Solder the 47 µF capacitor across C411, its positive lead to the L401 side (VCC) and its negative lead to the ground side.[1][3]
- Optionally, solder the 1 µF ceramic across C411 as well.[1]
exxos's results: 1 µF alone did not fully cure the ghosting, 10 µF cured about 95 % of it, and 47 µF worked best, perhaps improved slightly by adding the 1 µF ceramic. Larger values can be used, but he does not recommend less than 47 µF.[1]
Optional: RGB noise capacitors
[edit | edit source]exxos notes that Atari fitted small capacitors from the RGB outputs to ground on some models but not on the STE. To reduce vertical interference patterns and dot crawl on some televisions, he solders a 47 pF capacitor from each of the red, green and blue signal points to ground, at the points marked on his photograph. Larger values reduce interference further but blur the picture.[1]

Reassemble
[edit | edit source]Refit the shields, the board assembly, the supply, the drive and the case in Atari's reassembly order, with the three longer case screws in the round holes.[4]
Testing
[edit | edit source]- Show a light screen with dark lines and objects, such as the boot screen, on the same monitor or television as before, and compare with the "before" image above.[1]
Mega STE
[edit | edit source]exxos found slight ghosting on one Mega STE and cured it with a low-ESR 10 µF capacitor across C506. He describes this as work in progress and asks owners to confirm it.[1]
Related pages
[edit | edit source]- Atari 1040STE and Atari 520STE
- Atari STE Troubleshooting Guide
- Atari 1040STE Reset Circuit Repair
- Atari 1040STE Hard Disk Data Corruption Repair
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 exxos (Chris Swinson), "The LaST Upgrade, part 23: M/STE video ghosting fix", exxosforum.co.uk, last updated 16 February 2024: the ghosting, its cure by extra capacitance across C411, the results with 1 µF, 10 µF and 47 µF, the suggested Panasonic ECA-1CM470 and Multicomp MCMLR50V105MY5V parts, the RGB-only testing, the Mega STE variant at C506, and the optional 47 pF capacitors on the RGB lines.
- ↑ exxos, "MANDATORY FIXES", exxos's Atari, Amiga & retro forum, 31 January 2019, item 8, "STE – Video Ghosting Fix": the STE and Mega STE suffer from ghosting in the video.
- ↑ 3.0 3.1 3.2 Atari Corporation, STe schematic, drawing C300780-001, revision A, 3 October 1989, sheet 4: Q400–Q402 (2N3904), L401, C411 (0.47 µF), the 75 Ω output resistors and the video socket. Hosted here: File:Atari STE Schematic Rev A C300780-001.pdf.
- ↑ 4.0 4.1 Atari Corporation, 520STE/1040STE Field Service Manual, section 4, disassembly and reassembly (printed pp. 43–44, PDF pp. 48–49). Hosted here: Atari 520STE/1040STE Field Service Manual (PDF).