Jump to content

Atari 5200 RAM and Memory Timing Repair

From RetroTechCollection
Atari 5200 four-port motherboard RAM and 74LS258 area
The memory area of a four-port board with A designators: eight Motorola MCM4517P15 16K × 1 DRAMs, the two Hitachi HD74LS258P multiplexers at A16 and A17, A14, A15, A27, C137 and C145 (photo: Evan-Amos, public domain)

The Atari 5200 has 16 KB of RAM in eight 16K × 1 dynamic RAM chips (U18 to U25, or A18 to A25 on the later boards), addressed through two 74LS258 multiplexers (U16 and U17, or A16 and A17).[1][2] A faulty RAM chip, a multiplexer with the wrong timing or a solder bridge on an address line gives a black or scrambled screen. Atari's field service manual finds the failing RAM chip with the diagnostic cartridge, and four Atari tech tips describe board-level faults and their fixes: a solder bridge at the cartridge connector, Signetics multiplexers, the 74LS158 substitution, and Rockwell 6502 processors with a timing defect.[3][4][5][6][7]

Which board

[edit | edit source]

Atari's manual describes three boards: the original four-port CA018087 with U designators, the four-port "universal" CA020108 and the two-port CA021374, both with A designators. A universal console has a + as the third character of its serial number.[8] The tech tips apply to particular boards:

Atari's memory-related fixes by board
Fix Boards
Tech Tip 12: A0 address trace bridged to the REF feed-through at J1 CA018087[4]
Tech Tip 13: Signetics 74LS258s at A16 and A17 Four-port universal and two-port[5]
Tech Tip 17: 74LS158s fitted at A16 and A17 Two-port[6]
Tech Tip VCS 7: Rockwell "RC" 6502 with date code 8250 or later The board with U14 and U6 designators[7]

Symptoms

[edit | edit source]
  • The diagnostic cartridge's RAM test shows an error code from 0 to 7 on the error summary. The code names the chip: 0 is U25, 1 U24, 2 U23, 3 U22, 4 U21, 5 U20, 6 U19 and 7 U18.[9]
  • A blank dark screen at power-up, or garbled data with a cartridge fitted, which may change when the board is flexed near the cartridge connector J1: Tech Tip 12, on CA018087.[4]
  • A scrambled screen or no video at all on a universal or two-port board: Tech Tip 13.[5]

A black screen can also come from the supply, the clocks or the reset line. Atari's black-screen chart checks those first; see the Atari 5200 Troubleshooting Guide and Atari 5200 Power Supply Circuit Repair.[10]

Tools and parts

[edit | edit source]
  • A multimeter and an oscilloscope (Atari's chart looks for 4 V peak-to-peak signals), the Diagnostic Cartridge 1.1, an X-acto knife for Tech Tip 12, and a DVM to confirm a cut trace for Tech Tip VCS 7.[11][4][7]
  • Atari's parts:[1][5][6][7]
Parts
Part Atari number
16K × 1 dynamic RAM (U18 to U25, A18 to A25) C018082
74LS258 multiplexer (U16, U17, A16, A17) C019052
74LS158 (two-port substitution only) C014345
390 pF ceramic capacitor (C145, C55) C014179-24
470 pF capacitor (Tech Tip 17 boards) C014179-16
470 Ω resistor 14-5471
100 pF capacitor (Tech Tip VCS 7) C014180-03

Every chip on the three boards is in a socket, according to Atari's parts lists: 16-pin sockets for the RAMs and multiplexers, and 14-pin sockets for U14 and U28 on CA018087 and for A14, A15, A26 and A27 on the later boards.[1]

Procedure

[edit | edit source]

Finding the chip

[edit | edit source]
  1. Run the RAM test on the diagnostic cartridge. The screen is black for about ten seconds; if the test fails, an error code appears.[3]
  2. Swap the RAM chip that the code names (table above) for a known-good one.[9][3]
  3. If that does not cure it, swap U15, U16, U17 and U28 on a CA018087 board, or A14, A15, A16 and A17 on a CA020108 board.[3]
  4. Follow Atari's swap-out rule: replace parts one at a time with known-good ones, leave each in place, then refit the originals one by one to find which were faulty.[12]

Atari's RAM checks for a black screen

[edit | edit source]

Atari's black-screen chart reaches the RAM once the supply, clocks and reset have passed.[10][11][13]

  1. Look for a data signal on pin 2 of each RAM (U18 to U25). If it is missing, repair an open trace from the RAM's pin 2 to U2 (the 6502), or replace the RAM.
  2. Look for a data signal on pin 14 of each RAM. If only one chip lacks it, replace that chip.
  3. If pin 14 carries data, swap U14, U15, U16 and U17 in turn. If the display is still bad, Atari names U28 (CA018087 only), L4 to L6, C30 to C33 and an open address line to the RAMs; after repairing those, swap U18 to U25.
  4. If several chips lack data on pin 14 and the console still does not work, look for a 4 V peak-to-peak signal on U28 pin 6. If it is missing, U28, L4 to L6 or C30 to C33 is faulty.
  5. With U28 pin 6 good, look for 4 V peak-to-peak on pin 4 of the RAMs. If it is missing, swap U14 and U28, or look for an open from RAM pin 4 to U14 pin 8.
  6. With pin 4 good, look for 4 V peak-to-peak on pin 15 of the RAMs. If it is there, swap U17. If not, swap U17 and U14, or look for a faulty R133, C140, R68 or C55.

Tech Tip 12: bridge between A0 and REF at J1 (CA018087)

[edit | edit source]
Atari 5200 Tech Tip 12 A0 and REF traces at J1 (figure 1)
Solder side at the cartridge connector J1: the A0 address trace and the REF feed-through pad where excess solder bridges them (Tech Tip 12, figure 1)

Atari's five steps, in order:[4]

  1. Turn off the power and disconnect the AC and interconnect cables.
  2. Dismantle the console to expose the component side of the board.
  3. Find the cartridge connector J1, the A0 address trace next to it and the feed-through pad of the REF trace (figure 1).
  4. Remove the excess solder from the pad and wipe the area clean. Inspect the pad, and if necessary cut a shallow groove between the A0 trace and the pad with an X-acto knife, taking care not to nick the trace beside the pad.
  5. Reassemble and test the console.

Tech Tip 13: Signetics 74LS258s at A16 and A17

[edit | edit source]
Atari 5200 Tech Tip 13 resistor and capacitor fix (figure 1)
The second 390 pF capacitor across C145 and the 470 Ω resistor from C137 to R134 (Tech Tip 13, figure 1)

The timing of some Signetics 74LS258AN chips (C019052) distorts the RAM data. Manufacturing corrected some consoles, but an unknown number left the factory without the change.[5]

  1. Solder a second 390 pF capacitor (C014179-24) across C145.[5]
  2. Fit a 470 Ω resistor (14-5471) from C137 to R134, as in figure 1.[5]
  3. If the screen is still faulty, swap A16 and A17 for 74LS258s from another maker. Atari says not to use a Signetics part.[5]

The photographed universal board has Hitachi HD74LS258P chips at A16 and A17.[14]

Tech Tip 17: two-port boards with 74LS158s

[edit | edit source]

Because 74LS258s were short, some two-port consoles were built with 74LS158s (C014345) at A16 and A17. Those boards have these changes:[6]

  • the traces between pins 11 and 12 of A15 cut on both sides of the board;
  • jumpers from A15 pin 11 to A27 pin 3, from A27 pin 1 to A14 pin 9, and across A27 pins 1 and 2;
  • C55 and C145 changed from 390 pF to 470 pF (C014179-16).

If A16 or A17 has to be replaced on such a board, Atari says to replace both with 74LS258s (C019052); the changes made for the 74LS158 do not affect the 74LS258.[6]

Tech Tip VCS 7: Rockwell 6502s marked RC

[edit | edit source]
Atari 5200 Tech Tip 7 R-C network (figures 1 and 2)
The R-C network on the schematic and the factory modification on the component side at U14 (Tech Tip VCS 7, figures 1 and 2)
Atari 5200 Tech Tip 7 R-C network on the solder side (figure 3)
Where to add the network on the solder side, between U14, U17, U6 and C27 (Tech Tip VCS 7, figure 3)

Rockwell 6502s stamped RC with a date code of 8250 or later have a timing defect. The factory added an R-C network on the component side at U14A pin 1 and U6A pin 4; the network can stay when a 6502 from another maker, or a Rockwell with a different date code, is fitted.[7] To fit an RC 6502 on a board that does not have the factory network, add it on the solder side with a 100 pF capacitor (C014180-03), a 470 Ω resistor (14-5471) and about 2 inches of sleeving:[7]

  1. Straighten the lead of C27 on the solder side and solder one lead of the 100 pF capacitor to it.
  2. Point A is an unoccupied hole between U14 and U17, connected directly to U14 pin 1. Cut the trace between points A and B as close to point A as possible, and check with a DVM that it is open.
  3. Sleeve one lead of the 470 Ω resistor, insert it into point A and solder it.
  4. Wrap the free lead of the 100 pF capacitor round the resistor lead at point A and solder it.
  5. Clear the solder from the hole at point B, directly beneath U6. Sleeve the other resistor lead, insert it into point B and solder it.

Testing

[edit | edit source]
  • Run the RAM test and the full diagnostic cartridge sequence. Atari's tech tips 13 and 17 say that their changes do not alter the field service manual's test procedures, and Tech Tip VCS 7 refers to the standard tests.[5][6][7]
  • For Tech Tip 12, check that the picture stays steady when the board is flexed gently near J1.[4]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 Atari, CX5200 Field Service Manual FD100127 Rev. 4, section 8, parts lists for CA018087, CA020108 and CA021374: RAMs, multiplexers, C145 and C55, and the IC sockets.
  2. ↑ Atari, Inc., Atari 5200 Programmable Video Game System schematic, main board sheet ("ROM and RAM" section: U16 and U17 74LS258, U18 to U25 16384 × 1 DRAM). See File:Schematic Atari5200 4000.png.
  3. ↑ 3.0 3.1 3.2 3.3 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "RAM Test", p. 3-10.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Atari, Inc., Tech Tip VCS 12, "Printed Circuit Board (CA018087)", 6 June 1983, with figure 1. Same collection.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Atari, Inc., Tech Tip VCS 13, "Signetics 74LS258AN I.C. (C019052) at locations A16 and A17", 7 July 1983, with figure 1. Same collection.
  6. ↑ 6.0 6.1 6.2 6.3 6.4 6.5 Atari, Inc., Tech Tip VCS 17, "Additional information to accompany TT VCS 13", 2 August 1983, for the two-port board (CX5200C). Same collection.
  7. ↑ 7.0 7.1 7.2 7.3 7.4 7.5 7.6 Atari, Inc., Tech Tip VCS 7, "Defective Rockwell 6502 MPU on CX5200 PC Board", 20 January 1983, with figures 1 to 3, in Atari 2600 and Atari 5200 Field Change Orders, Upgrade Bulletins, Tech Tips. Hosted here as Atari 2600 and 5200 Field Change Orders and Tech Tips.
  8. ↑ Atari, Inc., CX5200 Field Service Manual, FD100127 Rev. 4, July 1983, section 1, pp. 1-1 and 1-2: the three boards. Hosted here as Atari CX5200 Field Service Manual.
  9. ↑ 9.0 9.1 Atari, CX5200 Field Service Manual FD100127 Rev. 4, Table 3-1, "Diagnostic Error Codes", p. 3-9.
  10. ↑ 10.0 10.1 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Black Screen Troubleshooting", pp. 4-2 to 4-6.
  11. ↑ 11.0 11.1 Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Black Screen Troubleshooting (Cont.)", p. 4-7: RAM pins 2, 14 and 4, U28 pin 6, U14 to U17, L4 to L6 and C30 to C33.
  12. ↑ Atari, CX5200 Field Service Manual FD100127 Rev. 4, p. 4-1: the swapout procedure.
  13. ↑ Atari, CX5200 Field Service Manual FD100127 Rev. 4, "Black Screen Troubleshooting (Cont.)", p. 4-8: RAM pin 15, U17, U14, R133, C140, R68 and C55.
  14. ↑ Evan-Amos, photograph of an Atari 5200 four-port motherboard, Wikimedia Commons, public domain: File:Atari-5200-4-Port-Motherboard-Flat.jpg.