Jump to content

Atari 520ST Power Supply Repair

From RetroTechCollection
Atari 520ST power supply board (SAMS Computerfacts CSCS12)
The board inside the external supply of a US 520ST, with SAMS's labels for Q1–Q3, IC1–IC3 and the presets VR1 and VR2. The reservoir capacitors C1 and C2 are at the top (photo: Howard W. Sams & Co.).

The Atari 520ST runs from a separate power supply that plugs into the power socket on its back panel. Atari's service manual rates the supply at 3 A on +5 V and 30 mA each on +12 V and −12 V, with 36 W maximum input, and describes it as a linear supply with no adjustments.[1] The German Atari museum lists it as the Atari PS31 on its page for the 520ST, 260ST, 520ST+ and 520STM, which share the short case.[2]

Howard W. Sams's service data for a US 520ST shows what is inside: a mains transformer and bridge rectifier, a +5 V regulator built from an MB3759 controller (IC1) and a 2SB825 transistor (Q1), and separate +12 V and −12 V regulators (IC2 and IC3) on their own windings.[3] The supply covered here is that unit; supplies for other mains voltages may differ in detail, and the capacitor values Console5 lists for its own example are on the Atari ST Capacitor Replacement Guide.

Symptoms

[edit | edit source]
  • Computer dead, no power LED. Check the supply's outputs before the computer.[3]
  • +5 V missing, low or too high.[3]
  • RS-232 port dead with everything else working: the +12 V or −12 V output. The RS-232 driver U14 needs +12 V on pin 14 and −12 V on pin 1.[3]

The 520ST's power switch, SW1, is on the computer's main board and breaks only the +5 V line; the ±12 V rails stay live on the board while the supply is plugged in.[4] A machine that is dead with good supply outputs has a fault in the computer; see the Atari ST Troubleshooting Guide.

Safety

[edit | edit source]

Warning: the supply contains a mains transformer, and its primary side is at mains voltage whenever it is plugged in. Unplug it before opening it. SAMS recommends an isolation transformer for servicing.[3] The reservoir capacitors C1 and C2 (3300 µF) are on the low-voltage side but can still deliver a large current if shorted.[3]

Tools and parts

[edit | edit source]
  • Multimeter and, for ripple, an oscilloscope.
  • Test loads, from SAMS: a 5 Ω, 10 W resistor for +5 V and 560 Ω, ½ W resistors for +12 V and −12 V.[3]
  • Replacement fuse R19: 5 A, 250 V, quick-acting.[3]
Main parts on the supply board (SAMS, US 520ST)
Position Part Function
T1 Transformer Mains input
D1–D4 1N5400 Bridge rectifier for the +5 V section
C1, C2 3300 µF Reservoir, about 15.6 V
R19 5 A, 250 V quick-acting fuse +5 V section
IC1 MB3759 Controller for the +5 V regulator
Q1 2SB825 +5 V regulator transistor
Q2, Q3 2SC1384R, 2SC1815GR In the +5 V regulator circuit
D5 CTB-24 +5 V regulator diode
L1, L2, C3 Inductors and 1000 µF +5 V output filter
D7, C11, IC2, C12 1N4001, 220 µF, +12 V regulator, 47 µF +12 V output
D6, C9, IC3, C10 1N4001, 220 µF, −12 V regulator, 47 µF −12 V output

Source: SAMS's schematic and parts list.[3] Electrolytic voltage ratings are not printed on SAMS's schematic; read them from the parts on your board.

Atari 520ST power supply schematic (SAMS Computerfacts CSCS12)
SAMS's schematic of the 520ST supply, with the voltages measured on a working unit: about 15.8 V on C1 and C2, 5.0 V at Q1's collector, 17.4 V into IC2 and 12.1 V out, and −11.9 V from IC3 (Howard W. Sams & Co.).

Procedure

[edit | edit source]

Open the supply and connect test loads

[edit | edit source]
  1. Unplug the supply from the mains and disconnect its plug (P9) from the computer. SAMS disconnects the computer while servicing the supply so that a fault cannot damage it.[3]
  2. Remove the four rubber pads on the underside of the supply and the four screws under them, and open the case.[1]
  3. Connect the test loads at the plug: 5 Ω, 10 W between +5 V (pins 1 and 6) and ground, and 560 Ω between +12 V (pin 4) and ground and between −12 V (pin 5) and ground.[3]

+5 V missing

[edit | edit source]

SAMS's sequence:[3]

  1. Check the fuse R19. If it is open, check the bridge diodes D1–D4 and the reservoirs C1 and C2 for a short before fitting a new fuse.
  2. Check for about 15.6 V at the emitter of Q1. If it is missing, check the transformer T1, the diodes D1–D4 and the mains lead.
  3. If the emitter voltage is right, check for 5.0 V at Q1's collector. If it is missing, check Q1, Q2, the controller IC1 and the parts around it.
  4. If 5.0 V is present at Q1's collector but not at the plug, check the inductors L1 and L2, the output cable and the plug P9.

+5 V low or too high

[edit | edit source]
  1. Low: check for about 15.6 V at Q1's emitter. If that is low, check D1–D4 and C1 and C2. If it is normal, check Q1, Q2, IC1 and the parts around them.[3]
  2. Too high: check Q1 and Q2 for shorts or leakage, then IC1 and the parts around it.[3]

+12 V or −12 V missing

[edit | edit source]
  1. +12 V: check for about 17.4 V at pin 1 of IC2. If it is missing, check D7 and the transformer T1; if it is low, check C11. If it is normal, check IC2 and C12.[3]
  2. −12 V: check for about 19.5 V across C9. If it is missing, check D6 and T1; if it is low, check C9. If it is normal, check IC3 and C10.[3]

Recapping

[edit | edit source]

The electrolytics in the supply are C1, C2 and C3 on the +5 V side, C9, C10, C11 and C12 on the ±12 V side, and C4 (10 µF) in the regulator circuit.[3] Replace like for like in value, with at least the original voltage rating read from each part; see Capacitor Failure Symptoms for what aged capacitors look like.

Close up

[edit | edit source]
  1. Refit the board and the case, the four screws and the four rubber pads.[1]
  2. Repeat the output checks with the case closed before reconnecting the computer.

Testing

[edit | edit source]
Expected values
Point Value Source
Q1 emitter (C1, C2) About 15.6–15.8 V SAMS
+5 V output (Q1 collector) 5.0 V SAMS
IC2 input / output About 17.4 V / 12.1 V SAMS
C9 About 19.5 V SAMS
IC3 output −11.9 V SAMS
Rating 3 A at +5 V; 30 mA at +12 V and at −12 V; 36 W maximum input Atari
Typical demand of the computer 1.5 A at +5 V; 3 mA on each 12 V rail with RS-232 idle, 19 mA (+12 V) and 18 mA (−12 V) with it active Atari

Sources: SAMS's troubleshooting text and schematic;[3] Atari's service manual.[1]

With the supply connected to the computer, SAMS's check for a dead machine is 5 V at the junction of C71 and C72 on the main board. If it is missing there, check for 5 V at terminal 14 of the filter L3, then at pins 1 and 6 of the power connector J9; 5 V at J9 but not after L3 points at L3, and 5 V at L3 but not at C71 and C72 points at the power switch SW1.[3]

[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 Atari Corporation, 520ST/1040ST Computer Field Service Manual, C026118-002 Rev B (3.6), January 1987, section 1, "Power supply" (p. 1.6, PDF p. 10): the 520ST supply's outputs, rating, typical demand, and the four rubber pads and four screws that hold it closed. Hosted here: File:Atari 520ST and 1040ST Computer Field Service Manual.pdf.
  2. ↑ "Atari 520ST, 260ST, 520ST+, 520STM, 130ST und ST Junior", atari-computermuseum.de (in German), revised 26 June 2024: the specification table entry "Netzteil Typ Atari PS31".
  3. ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 SAMS Computerfacts CSCS12: Atari Model 520ST, Howard W. Sams & Co., June 1986, ISBN 0-672-08974-2. Power supply schematic with voltages and waveforms (printed p. 6, PDF p. 8); power supply board photograph (p. 13, PDF p. 15); parts list, power supply board semiconductors and the fuse R19 (pp. 22–23, PDF pp. 24–25); troubleshooting, "Computer dead" and "Power supply", including the test loads (p. 25, PDF p. 27). Internet Archive.
  4. ↑ Atari (Japan) Corporation, Schematic Diagram (520ST/260ST), drawing C070231, revision M, sheet 1: power connector J9, filter L3, switch SW1 and reservoir C106. Hosted here: File:Atari 520ST Schematic C070231.pdf.