Jump to content

Atari 800 Power Supply Repair

From RetroTechCollection
Atari 800 power supply schematic (Field Service Manual figure 2-8)
Atari's schematic of the 800 power supply board: the bridge CR206 to CR209, the 7805 regulator A202 with R203 across it for +5 V, the doubler and 78M12 regulator A201 for +12 V, the −5 V supply with the two LEDs, and the RF modulator, SIO, monitor and console key connections

The Atari 800 takes 9 V AC from an external transformer and makes its own +5 V, +12 V and −5 V rails on a power supply board inside the console.[1] The same board carries the RF modulator, the peripheral (SIO) socket, the monitor socket and the four console keys (SYSTEM RESET, OPTION, SELECT and START).[1] The power switch S202 and the interlock switch S201, which breaks the supply when the top panel is opened to change a cartridge, are in the AC input.[1] Howard W. Sams's Computerfacts for the 800 gives a voltage at each stage of the board.[2]

Symptoms

[edit | edit source]
  • Neither power LED (CR210 and CR211) lights.[2]
  • A snowy screen with no Memo Pad. Atari's chart checks for +5 V at J201 pin 17 first.[1]
  • A black or grey screen. Atari's chart checks for −5 V at J201 pin 1 and +12 V at J201 pin 21.[1]

Safety

[edit | edit source]
  • The adaptor plugs into the mains. Measure it only at its output plug.
  • Let the large reservoir capacitors discharge after switch-off before handling the board.
  • Unplug the adaptor before removing or refitting the power supply board.

Tools and parts

[edit | edit source]
  • A multimeter with AC and DC voltage ranges, and continuity.
  • A cross-head screwdriver.
  • A known-good adaptor. The FAQ lists Atari's 9 V AC adaptors for the 800 as the 15.3 VA C014319, which it calls "only barely adequate" for the 400, 800 and 1200XL, and the 31 VA C017945.[3]
  • Parts from Atari's parts list as needed:[1]
Atari 800 power supply parts (Atari parts list)
Position Part Atari number
A202 Voltage regulator, 5 V (drawn as 7805) C014348
A201 Voltage regulator, 12 V (drawn as 78M12) C014349
CR206–CR209 Rectifier diodes, MR501 C014398
CR202–CR205 Diodes, 1N4001 31-1N4001
CR201 Zener diode 1N5231B C014808-01
C207, C208 4700 µF 16 V radial C014374-01 or -02
C204, C205 2200 µF 16 V axial C014373
C201, C202 470 µF 16 V axial C014370
R203 33 Ω (2 W on the schematic) C014771
S201 Interlock switch C014387
S202 Power switch C014397-01
J206 Power jack C014715

Procedure

[edit | edit source]

Check the adaptor

[edit | edit source]
  1. Plug the adaptor into the mains and unplug its lead from the computer. Measure across the plug on the AC range: Sams gives 10.4 V AC.[2] Atari rates the input at 9 V AC.[1]
  2. If the voltage is wrong or missing, replace the adaptor.[2]

Remove the power supply board

[edit | edit source]
Atari 800 power supply removal (Field Service Manual figure 4-9)
Atari's figure 4-9: the RF cable, the three screws, the motherboard connector and the wire harness
  1. Turn the unit upside down, remove the five bottom cover screws and tilt the back of the bottom cover up and towards you to remove it.[1]
  2. Remove the two screws from the aluminium casting flange and the single screw from the lower left corner of the power supply board. Disconnect the speaker cable and set the speaker aside.[1]
  3. Turn the unit over and carefully pull the back of the top cover assembly up to 90°, separating it from the PCB module. Reach over the top cover, unplug the keyboard ribbon cable and set the top cover aside.[1]
  4. Unplug the RF cable from the power supply board, unplug the power supply harness and remove the three screws from the power supply board.[1]
  5. Lift the power supply board straight up.[1]

Sams's checks below are made with the adaptor connected and the power switched on.[2]

Measure the supply stage by stage

[edit | edit source]
Atari 800 power supply board layout (Field Service Manual figure 2-7)
Atari's component layout of the 800 power supply board

If none of the voltages from the rectified DC onwards is present, Sams says to check the interlock switch S201 and the power switch S202, and to replace the board if they are good.[2] Otherwise work down the table; Sams also says to check for shorts to ground at each stage.[2]

Atari 800 power supply checks (Sams CC7)
Stage Measure Expected If missing, check
AC input Cathode of CR207 to cathode of CR209 10.4 V AC Interlock switch S201, power switch S202, jack J206, adaptor
Rectified DC Input of A202 (Sams: pin 1; also the cathode of CR206) 12.5 V CR206–CR209, C207, C208
+5 V Output of A202 (Sams: pin 3) 5.1 V A202
Doubled DC Input of A201 (Sams: pin 1) 24.4 V CR204, CR205, C203, C212, C204, C205
+12 V Output of A201 (Sams: pin 3) 11.8 V A201
Negative DC Anode of CR202 −11.9 V CR202, CR203, C201, C202
−5 V Anode of zener CR201 −5.0 V CR201, power LEDs CR210 and CR211, R201, R202

[2]

Sams numbers the regulator pins input 1 and output 3. Atari's schematics draw the same regulators with the input marked 3 and the output marked 1, so identify each pin by what it connects to.[2][1]

Follow Atari's flowcharts

[edit | edit source]
  1. With +5 V missing at J201 pin 17, Atari's chart says to check, repair or replace the bridge diodes CR206 to CR209, replacing 1N4001-type diodes there with 1N5391 (C017988); to check that the regulator A202 has +5 V; and to check C208, C209, R203 and S202.[1]
  2. With −5 V missing at J201 pin 1, the chart names a voltage regulator, CR204 and CR205 (replacing 1N4001 types with 1N5391), C203 to C205 and C212. On the schematic the −5 V supply is CR201 to CR203 with C201 and C202, the parts Sams names, so check those as well.[1][2]
  3. With +12 V missing at J201 pin 21, the chart names the regulator A201, CR204 and C203 to C205.[1]
Rails at the motherboard connector J201 (Atari figure 2-8)
Rail J201 pin
−5 V 1
+12 V 21
+5 V A 18, 19
+5 V B 17
Ground 15, 16, 22

[1]

Refit the board

[edit | edit source]
  1. Align the power supply connector with the motherboard pins, set the board down over the guide pins on the casting and press it gently down.[1]
  2. Fit the strip connector between the power supply and the motherboard, and refit the three power supply screws.[1]
  3. Plug the power supply harness from the motherboard onto the power supply pins with the orange or purple wire towards the aluminium casting.[1]
  4. Plug the short end of the RF cable into the power supply jack.[1]
  5. Set the top cover upside down, lower the module assembly into it with the cartridge door latches turned inwards, and make sure the RF cable is not trapped between the power supply board and the top cover standoff. Lift the motherboard an inch, plug in the keyboard harness and refit the two front screws.[1]
  6. Set the speaker into its receptacle foam side down and reconnect it. Fit the bottom cover, making sure the RF cable comes out through its hole, and refit the five screws.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge. Both power LEDs should light and the ATARI COMPUTER - MEMO PAD screen should appear.[2][1]
  2. Measure the rails at J201 against the table above.[1]
  3. Open and close the cartridge door to check that the interlock switches the machine off and on.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: power supply description (pp. 1-6 and 1-16), 800 power supply silkscreen and schematic (figures 2-7 and 2-8, pp. 2-12 and 2-13), 800 disassembly and assembly (section 4, pp. 4-9 to 4-12 and 4-17 to 4-19), 800 flowcharts AA and BB (pp. 7-3 and 7-4), 800 parts list (power supply assembly CA014171). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: "Power Supply" (service checks) and "Power Supply" (troubleshooting guide). Scan on the Internet Archive.
  3. ↑ Michael Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009, section 6.7, "What are the power requirements for my Atari components?". Text at faqs.org. Community reference.