Jump to content

Atari 850 Power Supply Repair

From RetroTechCollection
Atari 850 power supply schematic (service manual figure A3-1)
Atari's figure A3-1: the 850's on-board power supply, with test points A to J

The Atari 850 Interface Module takes 9 V AC from an external adaptor and makes its own +5 V, +10 V and -8 V on the main board. +5 V runs the 6507, the ROM, the two 6532s and the buffers; +10 V and -8 V feed only the serial port line drivers and, for +10 V, the clock circuit.[1] A dead +5 V rail stops the module booting; a weak +10 V or -8 V rail lets it boot but spoils the serial ports. Atari's 850 Interface Module Service Manual gives a test point for each stage of the supply and names the parts behind each one.[1] The steps below follow the supply in that order, from the adaptor input to the three outputs.

Symptoms

[edit | edit source]
  • The power LED does not light and the module does not boot. Atari says the supply is then probably faulty, though a lit LED does not prove that +5 V is good.[1]
  • The module boots but no I/O instructions are executed, or every serial port gives errors: check the +10 V and -8 V supplies.[1]
  • Serial ports work with some devices and not others, or give intermittent errors; faults confined to output from the 850. Output uses +10 V and -8 V and input does not.[1]
  • Regulator A113 runs hot and +10 V is low: a line driver is loading the rail.[1]

Faults that are not in the supply (clock, reset, processor, ROM and RAM) are covered in the Atari 850 Troubleshooting guide.

Safety

[edit | edit source]

Atari states that the 850 has no high voltages by design; mains voltage is confined to the external adaptor.[1] The chips are static-sensitive: Atari asks for a grounded anti-static work surface and a wrist strap, and warns against laying the board on plastic sheets such as Mylar page protectors.[1] Do not power the 850 from the 830 modem's adaptor; Atari warns that it can seriously damage any other Atari unit.[2]

Tools and parts

[edit | edit source]
Power supply parts (service manual appendix 8 and figure A3-1)
Ref Part Atari number Stage
CR114-CR117 Diode 1N4001 31-1N4001 Bridge rectifier (point C)
A112 Heatsink and regulator assembly; heatsink alone C014799 CA016075 +5 V regulator (point D)
C138 Electrolytic 2200 µF 16 V, axial C014373 +5 V
C141, C142 Electrolytic 470 µF 16 V C014368 Raw supply and the 18.5 V input to A113 (point E)
CR118, CR119 Diode 1N4001 31-1N4001 18.5 V input to A113 (point E)
A113 Regulator 7805 C014348 +10 V (point F)
C143, C137, C147 Electrolytic 10 µF 16 V C014392 Regulator outputs
CR112, CR113 Diode 1N4001 31-1N4001 Half-wave supply for -8 V (point G)
C136 Electrolytic 2200 µF 16 V, axial C014373 -8 V input (point G)
C139 Electrolytic 1000 µF 16 V C015999 -8 V input (point G)
Q102 Transistor 2N3906 C018991 -8 V pass transistor (point H)
CR111 Zener 1N5239B, 9.1 V C014808-05 -8 V reference (point J)
R154 180 Ω, 1/4 W 14-5181 -8 V
CR120 Schottky diode 1N5818 C016364 Beside A113 on figure A3-1
R155 75 Ω, 2 W C015728 Beside A113 on figure A3-1; its right leg is the +5 V quick-check point
J108 Power jack C014715 Adaptor input (points A-B)

[1]

The service manual's power supply appendix names the adaptor as CA014748; its parts list gives CA017964.[1]

How the supply works

[edit | edit source]

The 9 V AC from the adaptor enters at J108 and is full-wave rectified by CR114 to CR117. A112, a 5 V regulator, makes +5 V. A113 is a second 5 V regulator in cascade; it makes +10 V from an input of about 18.5 V, built from the full-wave rectified supply plus a half-wave rectified one through CR118 and CR119. The -8 V rail comes from a half-wave supply through CR112 and CR113, regulated by the pass transistor Q102 against the 9.1 V zener CR111.[1]

Procedure

[edit | edit source]

Open the module

[edit | edit source]
  1. Turn the 850 upside down and remove the four screws in the base, which hold the two halves of the shell together.[1]
  2. Hold the halves together, turn the module the right way up and lift off the top half. All voltage checks can be made from here.[1]
  3. For the +5 V checks Atari also removes the top half of the RF shield. Straighten the tabs of the bottom half that pass through the board and the top half, then lift the top half off.[1]

Quick check

[edit | edit source]
Atari 850 power supply quick test points (service manual figure 3-2)
Atari's figure 3-2: the quick-check points marked A, for -8 V, +10 V and +5 V, with ground at the heat sink

With the 850 powered, measure the three rails at the points Atari marks "A" in figure 3-2, against ground at the heat sink:[1]

  • -8 V at the emitter of Q102;
  • +10 V at the right leg of regulator A113;
  • +5 V at the right leg of R155.

Atari's tolerance is ±5 %, with no more than 0.1 V of ripple on +5 V.[1] If all three are good and the fault is still there, the supply is not the cause.

Trace the supply stage by stage

[edit | edit source]
Atari 850 power supply test points (service manual figure A3-2)
Atari's figure A3-2: where test points A to J are on the board, with ground at the heat sink or tab of A112

Check from the input towards the outputs. If only -8 V is wrong, do steps 1 and 2 and then go to step 6.[1]

Power supply test points (service manual appendix 3)
Step Point Expected If wrong, Atari names
1 A-B 9-10 V AC RMS, about 20-25 V peak to peak, with 120 V AC into the adaptor The adaptor
2 C Full-wave rectified, with no significant loss of peak against A-B CR114, CR115, CR116, CR117
3 D 4.75-5.25 V DC A112, or its loose heat sink
4 E About 18.5 V DC, not below 18 V C142, CR118, CR119
5 F 9.5-10.5 V DC A113
6 G Half-wave rectified 9 V, not below 8.8 V C136, C139, CR112, CR113
7 H At least 8.25 V negative C147, CR111, Q102 (R154 is unlikely)
8 J 8.7-9.1 V, the zener voltage CR111, if the waveform at J is the same as at G

[1]

For a low +5 V that the table does not explain:[1]

  1. Zero volts at some test points and not others means a broken trace.
  2. A low voltage means excessive loading.
  3. Check the heat sink on A112. A loose heat sink lets A112 overheat, which affects regulation.

For a low +10 V with a hot A113, find the load:[1]

  1. Switch off and remove the I/O cables.
  2. Remove A105 (an LM349, socketed) and switch on. If +10 V is now within specification, A105 was loading the rail; replace it.
  3. If not, switch off, remove A106 as well and recheck. It may be necessary to replace both.
  4. If +10 V stays low with both removed, the fault is in the supply itself.

Atari does not treat a small loss of -8 V regulation as a defect when all the serial ports and the 20 mA current loop are running at once.[1]

Replace the faulty part

[edit | edit source]
  1. Unplug the adaptor. Remove the board from the base of the shell, lifting it at the serial port edge first and bending the shell very slightly if needed.[1]
  2. Replace the part named at the failed test point, using the table above. The chips A105 to A111 sit in sockets (XA105-111) and can be swapped without soldering.[1]
  3. If you replace A112, make sure its heat sink is firmly attached.[1]
  4. Inspect the board while it is out: Atari asks for a flat board with no warping, no discolouration from overheated parts, and no solder splashes. Replace a visibly warped board.[1]

Reassemble

[edit | edit source]
  1. Refit the top half of the RF shield and bend its tabs back. Leave any serial number sticker on the shield in place.[1]
  2. Put the board back in the base, edge with the switch and LED first; the board then drops in.[1]
  3. Refit the top half of the shell and the four screws.[1]

Testing

[edit | edit source]
  1. Recheck the three "A" points: +5 V, +10 V and -8 V within ±5 %.[1]
  2. Switch on the 850 before the computer, then the computer. The module should boot and the computer should show READY.[1]
  3. Run Atari's port test on each serial port with pins 3 and 4 of the port joined, at the baud rates you use. The program is in the Atari 850 Maintenance Guide.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 Atari, Inc., 850 Interface Module Service Manual, CS 400/800-S004-B, April 1981: power supply and block diagram (pp. 2-3 and 2-4), work station and safety (pp. 3-2 and 3-3), disassembly and assembly (pp. 3-5 and 3-6), preventive maintenance (pp. 3-6 and 3-7), +10 V and -8 V and port buffers (pp. 3-10 to 3-12), 5 V checks (pp. 3-13 and 3-14, figure 3-2 on p. 3-9), power supply appendix 3 (pp. A3-2 to A3-5, figures A3-1 and A3-2), port test program appendix 7, parts list appendix 8. Hosted here as File:Atari 850 Interface Module Service Manual CS400-800-S004-B.pdf.
  2. ↑ Atari, Inc., Atari 850 Interface Module Operator's Manual, C017651, 1982: installation. Hosted here as File:Atari 850 Interface Module Operator's Manual C017651.pdf.