Atari 1010 Motor Drive Repair

When the tape in an Atari 1010 Program Recorder does not move, moves only on ADVANCE and REWIND, or runs at the wrong speed, the fault is in the belts, the motor supply or the motor control transistors that the computer switches through SIO pin 8. Atari's 1010 Cassette Recorder Field Service Manual has a "motor will not turn tape" flowchart and a speed adjustment procedure for each version, the Sanyo-built 1010S and the Chelco-built 1010C, and its schematics show the circuit each flowchart is testing.[1] The steps below follow those flowcharts stage by stage on the schematic.
Symptoms
[edit | edit source]- The tape does not move in any mode. Atari's symptom checklists give the drive belts, the motor and the motor control transistors: Q4 and Q5 on the 1010S, Q108 on the 1010C.[1]
- The tape moves on ADVANCE or REWIND but not when the computer starts the motor for a load. Atari's flowcharts point at the transistor and resistor that the computer's motor line drives: Q5 and R42 on the 1010S, Q107 and R143 on the 1010C.[1]
- The tape runs but programs will not load, and the 3 kHz test tone does not measure 0.33 ms per cycle: the speed needs setting.[1]
- The power light stays off. On later units the LED only lights after PLAY, REWIND or ADVANCE is pressed, so a dark LED with no key pressed is normal on those.[1] A dark LED with a key down is a supply fault; see the Atari 1010 Troubleshooting guide.
Identifying the version
[edit | edit source]On the 1010S, reading from left to right, PAUSE comes before STOP/EJ, and the FCC ID on the base starts BPA99H-1010. On the 1010C, STOP/EJ comes before PAUSE and the FCC ID starts BPA7YJ-1010.[1]
Safety
[edit | edit source]The recorder runs from an external adaptor supplying 9 V AC; there is no mains voltage inside.[1] The motor supply capacitors are small, but disconnect the adaptor before unsoldering anything.
Tools and parts
[edit | edit source]| Part | 1010S | 1010C |
|---|---|---|
| Motor drive belt | FC100228 | FC100250 |
| Counter belt | FC100229 | FC100251 (65 × 1 × 1) |
| Motor supply transistor | Q4, 2SB598P (FC100238) | Q108, 2SB856C (FC100258) |
| Motor control transistor | Q5, 2SC536 F-G (FC100237) | Q107, 9014C (FC100257) |
| Base resistor from SIO pin 8 | R42, 27 kΩ | R143, 4.7 kΩ |
| Motor supply capacitors | C29 1000 µF 16 V; C28 220 µF 16 V across the motor | C128 2200 µF 10 V; C127 220 µF 10 V |
| Tape drive with motor and heads | FA100224 | FA100246 |
| Power adaptor (9 V AC) | C017945 | |
- A meter, an oscilloscope, a known-good Atari computer with a BASIC cartridge, and Atari's 3 kHz audio test tape (FD100221) for the speed setting.[1]
- A 2.0 mm flat screwdriver for the speed adjustment on both versions.[1]
- For belt work, see Drive Belt Replacement. For testing and replacing the transistors, see Testing Diodes, Transistors and Regulators and Through-Hole Desoldering.
Procedure
[edit | edit source]Open the recorder
[edit | edit source]Atari's flowcharts start with the recorder opened to its "troubleshooting stage".[1]
1010S:
- Remove the four screws holding the bottom cover, then the shield screw and the shield.[1]
- Remove the two board screws, the LED screw and the two front panel screws, slide the front panel out, and slip the two blue wires out of their notch.[1]
- Lift the board without damaging the leaf switch and turn it over towards the keys; it stays wired to the mechanism. To hold the PLAY switch on while testing, close SW2 with a clip lead.[1]
1010C:
- Remove the four recessed screws holding the bottom cover. The board is on the cover; turn it over and set it beside the top cover.[1]
- Snap out the front panel and disconnect J104.[1]
- Press STOP/EJ to release the cassette door lock, remove the five screws holding the drive mechanism, turn it over and prop it so that the gears and belts can turn freely.[1]
The Atari 1010 Tape Head Replacement guide has Atari's figures for both versions.
Step 1: belts
[edit | edit source]- Check that the belts are sound and correctly fitted. If not, replace them and retest.[1]
- On the 1010C, the drive belt is changed without removing the mechanism: remove the screw and sleeve on the left of the largest drive wheel (screw 1 in figure 3-5), loosen the screw on the right of the wheel shield (screw 2), tilt the shield, and feed the new belt through the slot in the shield and round the three drive wheels without twisting it. The full procedure is in the Atari 1010 Maintenance Guide.[1]
Step 2: ADVANCE and REWIND
[edit | edit source]

Press ADVANCE or REWIND with a tape in place.[1]
If the tape moves, the motor, its supply transistor and the mechanism work, and the fault is in the path from the computer's motor line:
- 1010S: Atari names Q5 and R42. On the schematic the fast switch S3 pulls the base of Q4 down directly, while in PLAY the same job is done by Q5, whose base is fed through R42 (27 kΩ) from the motor control line.[1]
- 1010C: Atari names Q107 and R143. On the schematic S101 (ADVANCE) and S102 (REWIND) pull the base of Q108 down through R142 (470 Ω); in PLAY, Q107 does this, with its base fed from the motor control line through R143 (4.7 kΩ).[1]
Check the motor line itself before replacing either part: after a cold start in BASIC, POKE 54018,52 should start the recorder motor and POKE 54018,60 should stop it.[2] Replace the transistor or resistor Atari names, then go back to Atari's start-up test.[1]
Step 3: motor supply
[edit | edit source]If ADVANCE and REWIND do not move the tape either, measure the motor supply:[1]
- 1010S: measure at the positive side of C29. Atari's flowchart asks whether 9 V DC is present there; the schematic marks 12.5 V at that point and 12.7 V after the power switch S2.[1]
- 1010C: measure at pin 4 of J103 with the REWIND key held down. Atari's flowchart asks for 9 V DC.[1]
If the voltage is there and the tape still does not move, Atari's answer is to replace the drive mechanism (FA100224 or FA100246), which carries the motor.[1]
If the voltage is missing, the flowcharts name these parts, in this order:[1]
- 1010S: Q4, C29, R38. On the schematic R38 (3.3 Ω) sits between the switched supply and Q4, so check it for an open circuit as well as testing Q4 and C29.
- 1010C: Q108, L100 and C127 to C128. The schematic labels the 100 µH choke between Q108 and J103 as L101.
Reassemble
[edit | edit source]1010S: refit the mechanism with its five screws, keeping the motor wires clear of the counter belt; lay the board on the mechanism without bending the REW leaf switch and fix its two screws, the longer coarse-threaded one in the black plastic post; feed the blue head wires under the LED wires; refit the front panel, LED, RF shield and bottom cover.[1]
1010C: refit the mechanism with its five posts aligned and its five screws, the coarse-threaded screw in the plastic post; refit the front panel with the tab below the LED over the metal frame of the mechanism; reconnect J103 and J104; refit the bottom cover with its four recessed screws.[1]
Speed adjustment
[edit | edit source]

Set the speed after any motor or belt repair. The set-up is the same for both versions:[1]
- Connect the 1010 to the computer and its adaptor, fit BASIC and switch on. Insert the 3 kHz test tape (FD100221).
- Put the scope probe on pin 11 (audio out) of the unused I/O connector on the back of the 1010, with pin 4 as ground.
- Type
POKE 54018,52and press RETURN, then press PLAY.
1010S: turn the recorder over and adjust through the speed adjustment access in the cabinet bottom with a 2.0 mm flat screwdriver until one cycle of the tone measures 0.33 ms. If it will not adjust, Atari replaces the drive mechanism.[1] On the schematic the speed control is P1 (B-200), marked "TAPE SPEED ADJ.", beside the motor.[1]
1010C: with the recorder open to the troubleshooting stage, put a 2.0 mm flat screwdriver through the insulated hole in the bottom of the motor and turn the screw inside until one cycle measures 0.33 ms. At this point the 1010C procedure, as printed, says to replace the head if the waveform cannot be adjusted (p. 4-22), where the 1010S procedure replaces the mechanism.[1]
Testing
[edit | edit source]- With ADVANCE and REWIND, the tape winds in both directions.[1]
- After a cold start,
POKE 54018,52with PLAY held starts the tape andPOKE 54018,60stops it.[2] - The 3 kHz tone measures 0.33 ms per cycle on pin 11.[1]
- Atari's read/write verify test passes: load the diagnostic test tape (FD100008) with
CLOAD,RUNit, and follow the on-screen steps with the blank tape (FD100009).[1]
Related pages
[edit | edit source]- Atari 1010
- Atari 1010 Troubleshooting
- Atari 1010 Maintenance Guide
- Atari 1010 Tape Head Replacement
- Atari 1010 Documentation
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 Atari, Inc., 1010 Cassette Recorder Field Service Manual, FD100223 Rev. 02, September 1983: version identification and power supply (pp. 1-1 and 1-2), 1010C motor control operation (p. 1-3), schematics (fold-outs, PDF pp. 10 and 12), motor speed check (p. 3-4), read/write verify test (pp. 3-5 and 3-6), 1010S disassembly and assembly (pp. 3-7 to 3-9), 1010C disassembly, belt replacement and assembly (pp. 3-10 to 3-12, figure 3-5), "motor will not turn tape" flowcharts (pp. 4-4 and 4-17), speed adjustment procedures (pp. 4-8, 4-9, 4-21 and 4-22, figures 4-3 and 4-6), symptom checklists (pp. 5-1 and 5-2), parts lists (pp. 6-1 and 6-2). Hosted here as File:Atari 1010 Cassette Recorder Field Service Manual FD100223 Rev 02.pdf.
- ↑ 2.0 2.1 Atari, Inc., Consumer Product Service, Tech Tip, "ATARI 410 Recorder: 138, 140, and 143 Errors", 17 November 1982, servicer item 5: after a cold start in BASIC, pressing PLAY alone should not move the tape;
POKE 54018,52starts the motor andPOKE 54018,60stops it. Bound into the hosted copy of File:Atari 410 Program Cassette Recorder Field Service Manual FD100004.pdf.