Atari 1010 Tape Head Replacement

The play/record head of the Atari 1010 Program Recorder is replaced when it is worn or when the head alignment procedure will not bring the playback signal up to Atari's minimum. Atari's 1010 Cassette Recorder Field Service Manual gives a head replacement procedure for each of the two versions, the Sanyo-built 1010S and the Chelco-built 1010C, and finishes both with a head alignment against a 3 kHz test tape.[1] The two versions are built differently inside, so identify yours first and follow only its section.
Symptoms
[edit | edit source]- The head alignment check gives a signal below 560 mV (1010S) or 660 mV (1010C) at pin 11, and turning the head-adjust screw will not raise it. Atari's procedure for both versions is to replace the head when "the signal will not adjust but there is a signal present".[1]
- The head is visibly worn. Atari's maintenance procedure checks the head for wear and replaces it if necessary.[1]
- The recorder does not load or does not write. Atari's symptom checklists list the head among the possible causes of both, alongside other parts: IC1, IC2, Q1 and Q3 on the 1010S, and C119, C131, R138, Q101, Q103 and A100 on the 1010C.[1]
Clean the head first, check that the belts drive the tape, and run the tests in the Atari 1010 Troubleshooting guide before condemning the head. If the head alignment check fails and the waveform on pin 11 looks the same with the tape running and stopped, Atari's start-up flowchart goes to its no-audio chart (flowchart E) instead of the alignment procedure.[1]
Identifying the version
[edit | edit source]On the 1010S, reading from left to right, PAUSE comes before STOP/EJ, and the FCC ID on the base starts BPA99H-1010. On the 1010C, STOP/EJ comes before PAUSE and the FCC ID starts BPA7YJ-1010.[1]
Safety
[edit | edit source]The 1010 runs from an external power adaptor that supplies 9 V AC, which is rectified on the board.[1] There is no mains voltage inside the recorder, but unplug the adaptor and the I/O cable before opening it.
Tools and parts
[edit | edit source]| Item | 1010S | 1010C |
|---|---|---|
| Play/record head | FC100225 | FC100247 (BG-62 G205H) |
| Tape drive with motor, play/record head and erase head | FA100224 | FA100246 |
| 3 kHz audio test tape | FD100221 | |
| Diagnostic test tape and blank tape | FD100008 and FD100009 | |
- Atari's tool list is a standard tool kit, isopropyl alcohol for the head and lint-free swabs. Atari asks for 100 % lint-free swabs, not cotton buds.[1]
- A 2.9 mm flat screwdriver for the 1010S head-adjust screw.[1]
- An oscilloscope, a known-good Atari computer and a BASIC cartridge, and two jumper leads for the I/O pins.[1]
- A soldering iron for the head wires. See Through-Hole Soldering and Through-Hole Desoldering for the general method.
Procedure: 1010S
[edit | edit source]Opening the 1010S
[edit | edit source]
- Turn the recorder upside down and remove the four screws holding the bottom cover. Remove the cover.[1]
- Remove the shield screw and the shield.[1]
- Remove the two screws holding the board, but do not lift it yet. The longer screw with the coarser thread goes back into the plastic post.[1]
- Remove the screw holding the LED to the front panel, then the two screws holding the front panel, and slide the panel straight out.[1]
- Slip the two blue wires out of their notch in the board.[1]
- Lift the board carefully, without damaging the leaf switch, and turn it over towards the keys. It is wired to the mechanism and cannot be separated from it.[1]

- Remove the five screws holding the drive mechanism, lift it out of the top cover and set it securely on its supporting posts.[1]
Removing the old head
[edit | edit source]- Before moving the head, note four things. You need them for reassembly:[1]
- the order of the wires in the plastic guide (the ground wire is on top);
- where the ground tab sits under the Phillips screw;
- where the spring sits under the flat-head screw, against the plastic housing;
- the metal washer between the plastic housing and the plastic gear that runs beneath the head.
- Unscrew the screws on either side of the head and lift it out.[1]
- Unsolder the wires from the old head and solder them to the new one, one wire at a time, so that they cannot be confused.[1]
Fitting the new head
[edit | edit source]- Feed the ground wire through the plastic guide. Put the Phillips screw through the head plate, the ground tab and the plastic housing.[1]
- Place the spring in the plastic housing, press down gently and put the flat-head screw through the head plate and the spring.[1]
- Set the reassembled head housing onto the plastic gear that engages the play/record head, and tighten both screws carefully.[1]
Reassembling the 1010S
[edit | edit source]- Put the drive mechanism back in the top cover and refit its five screws. Keep the motor wires clear of the counter belt.[1]
- Without bending the REW leaf switch, lay the board component side down on the mechanism and fix it with its two screws, the longer coarse-threaded screw in the black plastic post.[1]
- Feed the blue head wires through their slot in the board, under the LED wires.[1]
- Slide the front panel on and secure it with the two screws at its base, then refit the LED.[1]
- Refit the RF shield, and the bottom cover with its four long screws.[1]
The 1010S head can be aligned with the recorder closed (below).
Procedure: 1010C
[edit | edit source]Opening the 1010C
[edit | edit source]
- Turn the recorder upside down and remove the four recessed screws holding the bottom cover.[1]
- Turn the bottom cover over to expose the board, which is mounted on it, and set it beside the top cover.[1]
- Snap out the front panel and disconnect J104 from the board.[1]
- Press STOP/EJ to release the cassette door lock, and remove the five screws that hold the drive mechanism in the top cover.[1]
- Turn the mechanism over and prop it so that the gears and belts are not obstructed when it runs.[1]
Replacing the head
[edit | edit source]- Before removing the head screws, note the order of the wires through the plastic guide, where the ground wire ring sits, and the spring under the brass head-adjust screw.[1]
- Remove the two screws holding the play/record head and lift the head out carefully.[1]
- Unsolder the wires from the old head and solder them to the new one, one wire at a time.[1]
- Put the wires back in the plastic guide.[1]
- Refit the screws, washer and spring as they were and tighten them gently.[1]
Leave the 1010C open for the alignment, which is done with the mechanism out of the case.[1]
Head alignment
[edit | edit source]

Atari's set-up for both versions:[1]
- Connect the computer to the television, plug the 1010 into its adaptor and the wall, connect the I/O cable, fit a BASIC cartridge and switch the computer on.
- Insert the 3 kHz test tape (FD100221).
- Remove the I/O cable. Connect pin 4 (ground) of the 1010 to pin 4 of the computer with a jumper lead, and pin 8 (motor control) of the 1010 to pin 8 of the computer with a second lead.
- Put the scope probe on pin 11 (audio out) of the unused I/O connector on the back of the 1010, with pin 4 as ground. Set the time base to 0.1 ms per division.
- Type
POKE 54018,52and press RETURN, then press PLAY on the recorder.
Then, for the 1010S:[1]
- Put the test tape under the cassette door so that the door stays open with the cassette in place; this exposes the head-adjust screw through the hole in the plastic cover.
- Turn the screw with a 2.9 mm flat screwdriver for the largest peak-to-peak signal, at least 560 mV.
For the 1010C, with the recorder open to the troubleshooting stage:[1]
- Insert the tape in the drive mechanism.
- Turn the head-adjust screw until the peak-to-peak signal is at its largest and at least 660 mV.
- Reassemble: put the mechanism back in the top cover with its five posts aligned and refit the five screws, the screw with the coarser thread in the plastic post. Refit the front panel so that the plastic tab below the LED fits over the metal frame of the mechanism, reconnect J103 and J104 if they were disconnected, and refit the bottom cover with its four recessed screws.
If the signal is present but will not peak, Atari's next step is another head; if it still will not adjust, the flowchart moves on to the electronics (flowchart E).[1] POKE 54018,60 stops the motor again.[2]
Testing
[edit | edit source]- Repeat the head alignment check: at least 560 mV (1010S) or 660 mV (1010C) on pin 11.[1]
- Keep the probes connected for the motor speed check. Unplug the jumper leads and refit the I/O cable; the 3 kHz tone should measure 0.33 ms per cycle. If it does not, set the speed as described in the Atari 1010 Maintenance Guide.[1]
- Run Atari's read/write verify test: load the diagnostic test tape (FD100008) with
CLOAD,RUNit and follow the steps on screen with the blank tape. The recorder is good if the test program saved to the blank tape loads and starts.[1] - Clean the new head with isopropyl alcohol and demagnetise it, as in Atari's maintenance procedure.[1]
Related pages
[edit | edit source]- Atari 1010
- Atari 1010 Troubleshooting
- Atari 1010 Maintenance Guide
- Atari 1010 Documentation
- Atari 410 Troubleshooting
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.44 1.45 1.46 1.47 Atari, Inc., 1010 Cassette Recorder Field Service Manual, FD100223 Rev. 02, September 1983: version identification (p. v and p. 1-1), power supply (pp. 1-1 and 1-2), maintenance procedure and connecting for testing (p. 3-2), head alignment check and figure 3-1 (p. 3-3), motor speed check (p. 3-4), read/write verify test (pp. 3-5 and 3-6), 1010S disassembly, head replacement and assembly (pp. 3-7 to 3-9, figures 3-3 and 3-4), 1010C disassembly and head replacement (pp. 3-10 to 3-12, figure 3-5), 1010S head alignment procedure (pp. 4-5 and 4-6, figure 4-1), 1010C head alignment procedure (pp. 4-18 and 4-19, figure 4-6), symptom checklists (pp. 5-1 and 5-2), parts lists (pp. 6-1 and 6-2). Hosted here as File:Atari 1010 Cassette Recorder Field Service Manual FD100223 Rev 02.pdf.
- ↑ Atari, Inc., Consumer Product Service, Tech Tip, "ATARI 410 Recorder: 138, 140, and 143 Errors", 17 November 1982, servicer item 5:
POKE 54018,52starts the recorder motor andPOKE 54018,60stops it. Bound into the hosted copy of File:Atari 410 Program Cassette Recorder Field Service Manual FD100004.pdf.