Jump to content

Atari 1020 Motor Pinion Gear Replacement

From RetroTechCollection
Atari 1020 plotter with top cover removed
An Atari 1020 with the top cover off, showing the platen and the pen carriage

The Atari 1020 Color Printer is built round an ALPS four-pen plotter mechanism with two small stepper motors, one driving the print head carriage and one the paper feed (platen).[1][2] Each motor drives the mechanism through a tiny nylon pinion gear pressed onto its shaft. The nylon has shrunk with age and the gears split on their shafts; the Tandy wiki, which covers the same ALPS mechanism in the Tandy CGP-115, says essentially all of them have split by now or soon will.[2] New pinions can be pressed on, or the originals repaired. The same mechanism was used in the Commodore 1520, the Tandy CGP-115 and many other plotters, and Paul Rickards reports repairing two Atari 1020s with the method he describes for the 1520.[2][3]

Symptoms

[edit | edit source]
  • At switch-on the mechanism buzzes or grinds and the print head vibrates in place instead of travelling, or the paper advance misbehaves. Rickards describes this on the Commodore 1520: the split leaves a gap in one of the 13 teeth, which binds against the gear it drives.[4][3]
  • Atari's flowcharts reach the same point from the electrical side. If the paper feed motor runs on its own but the paper does not feed, Atari blames the mechanical parts around the paper feed motor, to the right of the print head; if the print head motor runs but the head does not move, the mechanical parts around the print head motor, to the left.[1]

A 1020 that lights its LED but makes no movement at all at switch-on may have a different fault: one owner traced that to a dead 4 MHz crystal at X2. Missing drive pulses at A3 or A2 during the motor tests also point to the board, not the gears. Both are covered in the Atari 1020 Troubleshooting guide.[5][1]

Safety

[edit | edit source]

Unplug the AC adaptor before taking the printer apart; Atari's manual gives this warning for disassembly to any level.[1]

Tools and parts

[edit | edit source]
ALPS plotter motor pinion (Tandy CGP-115 wiki)
Teeth Module Bore Length Gears per plotter
13 0.25 1.5 mm 4.5 mm 2 (one per motor)

[2][6]

  • Replacement pinions, either machined brass, sold by Soigeneris as a set of two (enough for one mechanism, with the Atari 1020 on its compatibility list), or 3D printed from the open CAD model published by bkw777, which prints both gears as one piece that is snapped apart.[7][6][2]
  • For brass gears, a way to press them on: a small vise with plastic jaws (the Tandy wiki author used a Panavise 301), or a press made from a 2 inch (50 mm) C-clamp as Soigeneris suggests.[2][7]
  • To repair the original gears instead: calipers or a small clamp to hold the split closed, a 1/16 inch drill bit turned by hand, a toothpick, super glue and needle-nose pliers.[3]
  • A Phillips screwdriver and a flat-blade screwdriver.[1]

Procedure

[edit | edit source]

Opening the printer

[edit | edit source]

Atari's procedure:[1]

  1. Slide the top cover back to free its tabs from the bezel, lift it off and take out the paper roll.
  2. Turn the printer over and remove the two front rubber feet. The rear feet are glued in place.
  3. Remove the two machine screws under the front feet and the three wave screws.
  4. Turn the printer the right way up and lift the back of the upper case slightly to free it from the lower case.
  5. Pull the lower front of the bezel forward to release its hooks from the upper case, and set the bezel aside.
  6. Set the upper case upside down in front of the lower case, remove the two screws holding the switch assembly, and lift the upper case away.

The buttons stay with the upper case and the board with the lower, and the mechanism is connected to the board by a ribbon cable.[5] If the mechanism needs to come out, remove the screw at the right front that holds the mounting plate to the lower case, lift the plate with the printer module on it, and remove the ground wire from the board.[1] Unplug the mechanism's connector by its plastic body, not the wires.[5]

Finding the pinions

[edit | edit source]
Atari 1020 printer module exploded view (field service manual figure 6-1)
Atari's figure 6-1: the print head motor and paper feed motor sit behind the platen under the motor cover; the print head idle gear and bobbin gear are on the left side frame, the paper feed idle gear on the right

The two motors sit side by side behind the platen, covered by a thin metal motor cover. The print head motor's pinion is at the left-hand end, next to the print head idle gear and the bobbin gear with its wire. The paper feed motor's pinion is at the right-hand end, next to the paper feed idle gear.[1][3] The pinion is the small gear on the end of each motor shaft.[3]

  1. Remove the motor cover: put a flat-blade screwdriver between the cover and the frame unit and push the cover gently up and slightly forward.[1] With the cover off, both ends of each motor shaft can be reached without taking the motors out.[2]
  2. Look at each pinion for a split through one of its teeth.[3]

Removing a pinion

[edit | edit source]
  1. Remove the pinion from the motor shaft. It is a press fit and slides off. Rickards moves the shaft gently towards the back of the case with a flat-blade screwdriver in one hand and slips the gear off with the other.[3]
  2. Take care not to damage the gear that meshes with the pinion.[3]

Fitting a brass pinion

[edit | edit source]
  1. Start the new gear on the end of the motor shaft and press it on with the vise or clamp, with one jaw on the gear and the other on the rear end of the motor shaft. With the motor cover off, the corners of the vise jaws reach both ends of the shaft with the motor still in place.[2]
  2. Keep metal off the rear end of the shaft. It sits very close to the motor bearing, and even a slight deformation there must be avoided; plastic jaws protect it, and with a steel-jawed vise put something between the jaw and the shaft.[2]
  3. Check that the pinion meshes properly with the gear next to it and turns without binding.[1][3]

Repairing an original pinion

[edit | edit source]

This is Rickards' method. Gluing the split itself does not work at this size. Instead the bore is opened up so the shaft no longer forces the split apart, and glue on the shaft fixes the gear to it.[3]

  1. Find the split in the gear removed from the shaft. Off the shaft it closes up, because the bore is slightly smaller than the shaft.[3]
  2. Clamp the gear gently with the split pressed closed; Rickards used small calipers.[3]
  3. Turning a 1/16 inch drill bit by hand, slowly drill out the bore until the bit passes right through. Clear the debris with a toothpick.[3]
  4. One face of the gear is closed and flat. Fit the gear on the shaft with that face away from the motor and check that the split no longer shows and that the gears turn freely without binding or pausing. Then take it off again.[3]
  5. Put a tiny dab of super glue on the motor shaft and slide the gear on. Roll the meshing gear back and forth with your fingers to spread the glue round the shaft, and stop with the split facing up.[3]
  6. If a gap still shows, close it gently with needle-nose pliers until the glue sets. Leave it overnight for the best bond.[3]

Rickards reports that of the 1520s, CGP-115 and two Atari 1020s he repaired this way, one failed again after heavy use.[3] He also notes that surplus ALPS mechanisms all had split gears, but that they make good donors if a motor itself is bad.[4]

Replacing a motor

[edit | edit source]

Only needed if a motor is faulty, for example when fitting one from a donor mechanism. Atari's procedure is the same for either motor:[1]

  1. Note how the motor wiring harness is threaded. It must not rub on the wire or be pinched under the printer mechanism when it goes back.
  2. Unhook the spring of the paper holding roller support plate from the frame, then remove the Phillips screw that holds the motor to the frame.
  3. Put a flat-blade screwdriver under the motor, between the frame unit and the motor, and prise gently to free the motor without bending the frame.
  4. Desolder the jumper wire between the small boards on the two motors, and remove the screw that holds the motor's board to the frame unit.
  5. For the print head motor, desolder the two reed switch wires (yellow and grey) from the board; for the paper feed motor, the two electromagnet wires (black and red). Note where each was attached.
  6. Unthread the harness from the frame unit and remove the motor.
  7. To refit, put the gear and motor shaft through the hole in the frame unit behind the roller support plate spring, turn the motor so its flange is level with the hole, and line the motor bushing up with the hole.
  8. Check that the gears mesh, then refit the motor screw, the support plate spring, the board screw and the jumper wire, and resolder the reed switch or electromagnet wires.
  9. Check the harness threading again.

See Through-Hole Desoldering and Through-Hole Soldering for the general method.

Reassembly

[edit | edit source]
  1. Refit the motor cover: the tab at its right front goes over the side frame, in front of the screw that holds the paper feed motor, and the back of the cover slides inside the frame unit.[1]
  2. Refit the mechanism, its connector and the ground wire if they were removed, then the switch assembly, upper case, bezel, screws and front feet in the reverse order of opening.[1]

Testing

[edit | edit source]

Atari's motor test programs run in BASIC on the computer. This one loops the carriage motor:[1]

10 OPEN #1,8,0,"P"
20 ?#1;"[ESC][ESC][CTRL-G]"
30 ?#1;"M480,0;0,0
40 GOTO 30

Where the manual prints ESCAPE, ESCAPE, CONTROL G inside the quotes on line 20, press ESC, ESC, then CONTROL and G together. For the paper feed motor, change line 30 to ?#1;"M0,999;0,-999. Press BREAK to stop either program.[1]

  1. Switch on with paper and pens loaded. The POWER key should stay down and the LED light. The print head moves to the far left, waits two or three seconds, draws four coloured squares and stops near the left margin.[1]
  2. Run the carriage motor program. The carriage should go to the right and then back to the left, with no grinding and no hesitation at any point in the pinion's turn.[1][3]
  3. Run the paper feed program. The paper should move forwards and back the same way.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 Atari, Inc., 1020 Color Printer Field Service Manual, FD100288 Rev. 01, August 1983: internal test p. 3-6, print head (carriage) and paper feed motor troubleshooting programs pp. 3-7 and 3-8 (PDF pp. 34-36); no paper feed and print head does not move flowcharts pp. 4-8 and 4-9 (PDF pp. 46-47); mechanical assembly, figure 6-1, p. 6-2 (PDF p. 54); disassembly warning, case disassembly and printer module removal p. 6-4 (PDF p. 56); motor cover and motor removal and replacement pp. 6-8 and 6-9 (PDF pp. 60-61). Hosted here as File:Atari 1020 Color Printer Field Service Manual FD100288 Rev 01.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Tandy Tech wiki, "CGP-115", sections "ALPS Plotter Engine" (the Atari 1020 among the plotters built on the ALPS DPG-1302 engine) and "Gears" (shrunk and split nylon pinions, gear specification, brass and 3D-printed sources, pressing brass gears on with a plastic-jawed vise with the motor cover removed), last edited 1 August 2026. Community reference.
  3. ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 Paul Rickards, "Commodore 1520 Plotter X/Y Gear Repair Guide", biosrhythm.com, 28 April 2016. Symptoms, location of the two pinions, removal, the drilled-bore and glued-shaft repair, and his note that he repaired two Atari 1020s by the same method. Personal repair guide.
  4. ↑ 4.0 4.1 Paul Rickards, "Commodore 1520 Printer Plotter", biosrhythm.com, 16 November 2009. Grinding motors, vibrating print head and erratic paper advance from split gears; surplus ALPS mechanisms as donors for bad motors. Personal repair write-up.
  5. ↑ 5.0 5.1 5.2 RetroNerd, "Atari 1020 Colour Printer Plotter Repair", 7 January 2024. Case opening, the ribbon cable between mechanism and board, and the dead X2 crystal. Community repair write-up.
  6. ↑ 6.0 6.1 bkw777, "ALPS_plotter_gears", GitHub: pinion gear model for the ALPS plotter engine, two per plotter (X and Y motors), printed as one piece and snapped apart. Open CAD model.
  7. ↑ 7.0 7.1 Soigeneris, "Alps Printer-Plotter Mechanism Pinion Gears (Set of 2)": two brass gears, 0.25 module, 13 teeth, 1.5 mm bore, enough for one mechanism, pressed on with a tool made from a 2 inch C-clamp; the Atari 1020 is on the compatibility list. Vendor page.