Jump to content

Atari 1040STE DMA Sound Repair

From RetroTechCollection
Atari STE DMA sound circuit (schematic C300780-001 sheet 5)
The STE's two DMA sound channels on Atari's schematic: a 74F374 latch, a DAC0802 converter, an LF347 buffer, an MF4 filter and two more LF347 stages for each of left (top) and right (bottom). R542 and R543 at the top left feed the converters.

The Atari 1040STE and Atari 520STE play digital samples through a DMA sound circuit that the earlier STs lack. For each stereo channel a 74F374 latch holds the sample, a DAC0802 converts it, and LF347 op-amps and an MF4 switched-capacitor filter smooth it. The two channels then join the YM2149's sound in an LMC1992 volume and tone control, U508, which drives the stereo phono outputs and the monitor's audio.[1][2]

The converters take +5 V through R542 (10 Ω) and −5 V through R543 (10 Ω), each with a 100 µF reservoir; the −5 V comes from a small switching regulator on the board, U205, and the op-amps run from an LM78L82 +8.2 V regulator fed from +12 V.[1][2]

Symptoms

[edit | edit source]
DMA sound faults
Symptom Where to look Source
No DMA sound +8 V regulator, the ± supplies, the LMC1992, R542, R543 Atari
No sound from the YM2149 or the DMA channels The LMC1992 first Atari
Crackles and pops in DMA playback The 74F374 latches and their grounds exxos
Whistles and noise The power supply; the metal shield missing or loose exxos

Sources: Atari's manual[2] and exxos.[3]

Tools and parts

[edit | edit source]
  • An oscilloscope, which Atari's DMA sound test uses at the phono outputs.[2]
  • A multimeter.
  • For the crackle fix, two 74LS374 latches and a short length of wire.[3]
  • Parts from the parts list: LMC1992 (U508), DAC0802 (U502, U503), LM78L82 regulator, 10 Ω resistors (R542, R543).[2]

Procedure

[edit | edit source]

Open the machine

[edit | edit source]

Atari's sequence for the STE:[2]

  1. Unplug the machine. Turn it upside down and remove the six screws in the square holes and the three in the round holes.
  2. Turn it upright, lift off the top case, unplug the keyboard harness at the right front corner, and unplug and lift out the disk drive.
  3. Remove the screw on the right of the power supply shield and the three screws between the back-panel shield and the supply shield, straighten the two twist tabs, lift the supply shield off, and remove the two screws at the supply's front corners.
  4. Remove the three screws at the front of the board assembly, lift it at the front and pull it forward.
  5. Straighten the upper shield's twist tabs (usually four), remove any copper tape and lift the shield off. Reconnect the keyboard and drive beside the board to test it.

Run Atari's tests

[edit | edit source]
  1. Run the diagnostic cartridge's audio test. It plays a low-to-high sweep on each of the YM2149's three channels. If both the YM2149 and the DMA parts fail, look at the LMC1992 first, because it controls both.[2]
  2. For the DMA part, connect an oscilloscope to the stereo phono outputs at 1 ms per division and 5 V per division. The test has four parts, each stepping from zero to full amplitude: mono 1 kHz on both channels, about 5–6 V; stereo 1 kHz and 500 Hz, one channel rising as the other falls, up to 5–6 V; treble, 12.5 kHz on both, about 6 V; bass, 50 Hz on both, about 6 V. Press the space bar to move from one part to the next.[2]

No DMA sound

[edit | edit source]
  1. Measure +8.2 V at the output of the LM78L82 regulator. If it is missing, check the +12 V feed and the regulator.[2][1]
  2. Measure +5 V after R542 and −5 V after R543, at the converters' supply. If −5 V is missing before R543 as well, check the switching regulator U205 that makes it.[2][1]
  3. Check R542 and R543 (10 Ω) for an open circuit with the power off.[2]
  4. With the DMA test running, follow each channel with the oscilloscope: the latch outputs, the DAC output, the LF347 buffer, the MF4 filter, the output stages to GIL or GIR, and the LMC1992's outputs to the phono sockets.[1]
  5. If the signals reach the LMC1992 but not the outputs, replace the LMC1992.[2]

Crackles and pops

[edit | edit source]
Atari STE DMA sound crackle fix wires (exxos)
exxos's crackle fix: two short wires from the latches U500 and U501 to a point beside C412 (photo: exxos).

exxos traced the crackling to short, sporadic pulses on the inputs of the DAC chips.[3]

  1. Solder two wires, as short and direct as possible, from the latches U500 and U501 to the point beside C412 that exxos shows in his photograph. These cured the crackling on the two machines he tested.[3]
  2. If the wires do not cure it, replace the two 74F374 latches with 74LS374s, which exxos found more immune to noise and less prone to spiking the ground.[3]

fenarinarsa wrote a test program, linked from exxos's page, that shows the fault up.[3]

Whistles and noise

[edit | edit source]
  1. Service the power supply first; exxos treats it as the first cause of noise in the STE's DMA audio. See Atari 1040STF Power Supply Repair.[3]
  2. Make sure the metal shield is fitted and secure; exxos found it necessary to reduce the whistles.[3]

Reassemble

[edit | edit source]

Refit the shields, the board assembly, the supply, the drive and the case in Atari's reassembly order.[2]

Testing

[edit | edit source]

Run the cartridge's audio and DMA sound tests again and listen to a sample-based program through the phono outputs.[2]

Mega STE

[edit | edit source]

On the Mega STE, exxos reports two cures for the same crackle: fitting the C300588 Shifter, or, in one owner's machine, soldering 33 pF (or 47 pF) capacitors from each DAC data line to ground.[3]

[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 1.4 Atari Corporation, STe schematic, drawing C300780-001, revision A, 3 October 1989, sheet 5: U500 and U501 (74F374), U502 and U503 (DAC0802), U504 and U507 (LF347), U505 and U506 (MF4), U508 (LMC1992), the LM78L82 +8.2 V regulator, R542 and R543 with C556 and C561, and the LEFT and RIGHT phono sockets. Hosted here: File:Atari STE Schematic Rev A C300780-001.pdf.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 Atari Corporation, 520STE/1040STE Field Service Manual. The negative supplies: U205 (TL497) makes −5 V for the audio section (section 1.4, printed p. 3, PDF p. 8); the audio subsystem (PDF p. 13); the audio and DMA sound tests (sections 3.13 to 3.13.2, printed pp. 32–33, PDF pp. 37–38); the symptom checklist, DMA sound (section 5.8, PDF p. 51); disassembly (printed pp. 43–44, PDF pp. 48–49); parts list (printed pp. 53–55, PDF pp. 58–60). Hosted here: Atari 520STE/1040STE Field Service Manual (PDF).
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 exxos (Chris Swinson), "The LaST Upgrade, part 31: STE DAC and LMC fix", exxosforum.co.uk, last updated 26 July 2026: the power supply as the first cause of DMA audio noise, the need for the shield to be fitted, the crackle traced to pulses on the DAC inputs, the short-wire fix and the replacement of the 74F374 latches with 74LS374, the test program by fenarinarsa, the Mega STE variant, and P. Putnik's LMC1992 mixer modification.