Jump to content

Atari 1200XL Operating System ROM Replacement

From RetroTechCollection
Atari 1200XL chip and component outlines with Atari part numbers (FD100217)
Atari's component outline page for the 1200XL, with the 28-pin OS ROM A (C060617) and OS ROM B (C060616) at the centre

The Atari 1200XL keeps its 16 KB operating system in two 8K × 8 chips: OS ROM A at U12 (Atari C060617) and OS ROM B at U13 (C060616), in the sockets XU12 and XU13.[1] Early production machines have EPROMs in these positions.[2] Atari's tech tip 18A replaces the original Rev. A EPROMs or ROMs with Rev. B ROMs (C060617B and C060616B) when the old parts have failed or when the SYSTEM RESET key does not work properly; Rev. B corrects the SYSTEM RESET problem and differs from Rev. A in nothing else.[3] The two chips are a set and are always changed together.[3]

Symptoms

[edit | edit source]
  • A red ROM bar in the memory test of the built-in self test.[1]
  • "ROM test failed". Atari's checklist gives U12, U13, U14, U18 and U22 as the causes.[1]
  • A green or yellow screen at switch-on. Atari's checklist gives U27, U1 to U9, U12 and U13.[1]
  • The SYSTEM RESET key does not work properly on a machine with the Rev. A operating system.[3]

Safety

[edit | edit source]
  • Switch off and unplug the 9 V AC transformer before pulling or fitting any chip.
  • Do not leave the television on a self test screen for long; Atari warns that the screen can burn.[1]

Tools and parts

[edit | edit source]
  • A medium cross-head screwdriver and an IC extraction tool.
  • A soldering iron and desoldering tool, for the jumper changes on an EPROM board.
  • A pair of Rev. B OS ROMs: U12 C060617B and U13 C060616B.[3]
  • Zero-ohm jumpers (Atari C060629), four of them for an EPROM board.[3]
  • To read the OS revision before opening the machine: an Atari BASIC cartridge (the 1200XL has no built-in BASIC).[4]

Procedure

[edit | edit source]

Identify the fitted operating system

[edit | edit source]
  1. With BASIC running, type PRINT PEEK(65527). The result is 10 for the first 1200XL operating system and 11 for the second.[4] Michael Current's FAQ lists revision 10 (dated 26 October 1982) with parts C060616A and C060617A and revision 11 (23 December 1982) with C060616B and C060617B, and notes that Best Electronics calls them Rev. A and Rev. B.[4]
  2. Run the self test (press HELP at the logo, select MEMORY, press START). The two long bars at the top represent the two 8K ROMs; a red bar marks a failed ROM.[1]
  3. Decide whether to change the chips. Tech tip 18A allows it in only two situations: the Rev. A parts have failed, or the owner has complained that SYSTEM RESET does not work properly.[3]

Open the machine

[edit | edit source]
Atari 1200XL console, RF shield and adjustment points (FD100217 figure 4-1)
Atari's exploded view of the 1200XL console and RF shield
  1. Turn the computer upside down and remove the six screws that hold the bottom cover to the top cover.[1]
  2. Lift away the bottom cover with the board and turn it right side up. Unplug the keyboard and LED connectors, noting which way round the LED connector goes.[1]
  3. Remove the six board screws and lift out the board and the cartridge connector.[1]
  4. Remove the eleven push rivets, separate the top and bottom RF shields and remove the fish paper.[1]
  5. Read the markings on U12 and U13 and note whether they are 28-pin EPROMs or 24-pin ROMs.[2]

If the board has ROMs

[edit | edit source]
  1. Lift out both ROMs.
  2. Fit the Rev. B ROMs, C060617B at U12 and C060616B at U13.[3]

If the board has EPROMs

[edit | edit source]

Tech tip 18A gives the conversion from Rev. A EPROMs to Rev. B ROMs. Make the jumper changes before inserting the ROMs.[3]

  1. Lift out both EPROMs.
  2. Remove the zero-ohm jumpers W11, W12 and W13, which are used with the 28-pin device only.[3]
  3. Install zero-ohm jumpers (C060629) at W6, W7, W8 and W9, which are used with the 24-pin device only.[3]
  4. Insert each Rev. B ROM with its pin 1 in pin position 3 of the socket, C060617B at U12 and C060616B at U13.[3]

The earlier tech tip 18 (12 July 1983), which 18A replaces, gave a longer jumper list: remove W1, W11, W12, W13 and R44 for the 28-pin device, and install W1, W6, W7, W8, W9 and R44 for the 24-pin device. Tech tip 18A does not mention W1 or R44.[2][3]

Reassemble

[edit | edit source]
  1. Lay the top shield upside down, place the board upside down on it, put the fish paper inside the bottom shield and lay them over the board with the adjustment holes clear. Refit the eleven push rivets.[1]
  2. Insert the cartridge connector, place the assembly in the bottom cover and refit the six board screws.[1]
  3. Reconnect the keyboard and LED connectors without twisting the LED cable, and refit the bottom cover with its six screws.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge. The power-on logo should appear.[4]
  2. Run the self test's memory test; both ROM bars should turn light green.[1]
  3. Press SYSTEM RESET to check that the machine restarts properly.[3]
  4. With a BASIC cartridge, PRINT PEEK(65527) should now return 11.[4]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 Atari, Inc., 1200XL Home Computer Field Service Manual, FD100217, Rev. 01, February 1983: self test (section 3, pp. 3-1 to 3-3); symptom checklist and console disassembly and assembly (section 4, pp. 4-1 to 4-4); parts list (section 5: U12 C060617, U13 C060616, sockets XU12 and XU13); component outlines at the end of the scan. Hosted here as Atari 1200XL Field Service Manual.
  2. ↑ 2.0 2.1 2.2 Atari, Inc., Consumer Product Service, Tech Tip 18, "Operating System (OS) ROMs", 12 July 1983, in the 1200XL Home Computer Field Service Manual (section 6). Hosted here as Atari 1200XL Field Service Manual.
  3. ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 Atari, Inc., Consumer Product Service, Tech Tip 18A, Atari 1200XL Computer OS, 29 September 1983 ("This Tech Tip Supercedes Tech Tip 18 Dated July 12, 1983"), in the 1200XL Home Computer Field Service Manual (section 6). Hosted here as Atari 1200XL Field Service Manual.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 Michael Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009: section 1.4, "What is the Atari 1200XL?" (boot options), and section 7.1, "What versions of the Atari Operating System (OS) are there?" (Freddy Offenga's table, version 3.6, and the PEEK(65527) values). Text at faqs.org. Community reference.