Jump to content

Atari 1200XL RAM Replacement

From RetroTechCollection
Atari 1200XL OS ROM 2764 and 64K x 1 DRAM pinouts (FD100217 figure D)
Atari's pinouts for the 1200XL's memory chips: the 28-pin 8K × 8 OS ROM at the top and the 16-pin 64K × 1 DRAM below, with data in on pin 2, data out on pin 14, +5 V on pin 8 and ground on pin 16

The Atari 1200XL holds its 64 KB of RAM in eight 64K × 1 dynamic RAMs (Atari part C060612), one for each data line, at U1 to U6, U8 and U9; 48 KB of it is directly available to programs.[1] All eight sit in 16-pin sockets, as do the two 74LS158 address multiplexers U7 and U10 and the memory management HAL U14.[1] Atari's diagnostic cartridge SALT 2.05 reports a failing RAM by data bit, and the field service manual gives the chip for each bit, so a RAM fault on this machine can usually be traced to one chip and fixed by swapping it.[1]

Symptoms

[edit | edit source]
  • Red blocks in the memory test of the built-in self test.[1]
  • A green or yellow screen at switch-on. Atari's checklist gives U27, U1 to U9, U12 and U13 as the causes.[1]
  • Red 1s in row D of the SALT 2.05 RAM test.[1]

Safety

[edit | edit source]
  • Switch off and unplug the 9 V AC transformer before pulling or fitting any chip.
  • Fit each chip the right way round. Atari's outline drawing shows the pin 1 end of each package.[1]
  • Do not leave the television on a self test screen for long. The self test does not go into attract mode, and Atari warns that the screen can burn.[1]

Tools and parts

[edit | edit source]
  • A medium cross-head screwdriver and an IC extraction tool.
  • A multimeter.
  • Replacement 64K × 1 DRAMs, 16-pin (Atari C060612).[1]
  • Optionally, Atari's SALT 2.05 diagnostic cartridge, which Atari specifies for the 1200XL.[1]

Procedure

[edit | edit source]

Run the self test

[edit | edit source]
  1. Connect the computer to a television, remove any cartridge and switch on.[1]
  2. Press HELP while the power-on logo is on the screen. Select MEMORY with SELECT and start it with START.[1]
  3. Two long bars at the top represent the two 8K OS ROMs. The three rows of sixteen blocks below them represent the RAM, one block per kilobyte. A block under test is white, turns light green if it is good and red if it is bad, and a failed block is not tested again.[1]
  4. The LEDs cycle one on and one off during the RAM test. The test loops until HELP or SYSTEM RESET is pressed.[1]

The self test shows where in memory the fault lies. On a 1200XL every RAM chip holds one bit of every byte, so the chip has to be found with SALT 2.05 or by swapping chips.[1]

Find the chip with SALT 2.05

[edit | edit source]
  1. Insert the SALT 2.05 cartridge and switch on. After a few seconds the SALT header appears. On a 1200XL, "ERR" in the ROM row and a red screen are not failures.[1]
  2. Type D and RETURN (display options), then E and RETURN for the diagnostic matrix, then C and RETURN for continuous testing.[1]
  3. Type R and RETURN to start the RAM test. The white four-digit number at the bottom right counts completed passes and the red number above it counts failures. Press the space bar to stop; the test finishes its current pass first.[1]
  4. Failures appear as red 1s. Only row D applies to the 1200XL. Read the failing column and find the chip in the table below.[1]
Defective RAM identifier (Atari, p. 3-10)
Column (data bit) Chip
D0 U9
D1 U8
D2 U6
D3 U5
D4 U4
D5 U3
D6 U2
D7 U1

[1]

The table skips U7, which is one of the two 74LS158 multiplexers.[1]

Open the machine

[edit | edit source]
Atari 1200XL console, RF shield and adjustment points (FD100217 figure 4-1)
Atari's exploded view of the 1200XL: top cover, the board inside its two-part RF shield, the cartridge connector and the bottom cover
  1. Turn the computer upside down and remove the six screws that hold the bottom cover to the top cover.[1]
  2. Lift away the bottom cover, which carries the board, and turn it right side up. Unplug the keyboard connector and the LED connector from the board, noting which way round the LED connector goes.[1]
  3. Remove the six screws that hold the board, and lift the board and the cartridge connector out of the bottom cover.[1]
  4. Remove the eleven push rivets from the shield, separate the top and bottom RF shields and remove the fish paper, taking care not to damage the board.[1]

Check the supply at the RAM

[edit | edit source]
  1. With the board connected and switched on, measure from pin 8 (+5 V) to pin 16 (ground) of the suspect chip.[1] Atari specifies each regulator's output as 5 V ±5 %.[1]
  2. If the supply is missing, work through Atari 1200XL Black Screen Repair before changing chips.

Replace the chip

[edit | edit source]
  1. Switch off. Lift the RAM chip that SALT names out of its socket.[1]
  2. Fit a new or known-good 64K × 1 DRAM with its pin 1 end the same way as the chip it replaces.[1]
  3. If several bits fail together, or the failure moves when chips are swapped, Atari's checklist for a failed RAM test widens the search to U7, U14 and U22. U7 and U14 are socketed; U22, the DDU-4 delay module (C060472), has no socket in the parts list.[1]
Parts Atari lists for a failed 1200XL RAM test
Position Part (Atari number) Socket
U1–U6, U8, U9 64K × 1 DRAM (C060612) XU1–XU11 (16-pin)
U7 (and U10) 74LS158 multiplexer (C014345) XU1–XU11 (16-pin)
U14 Memory management HAL (C060609) XU14 (20-pin)
U22 DDU-4 delay module (C060472) None listed

[1]

Reassemble

[edit | edit source]
  1. Lay the top shield upside down on the bench, place the board upside down on it, put the fish paper inside the bottom shield and lay the bottom shield and fish paper over the board, keeping the adjustment holes clear.[1]
  2. Refit the eleven push rivets.[1]
  3. Insert the cartridge connector into the board and shield assembly, place it in the bottom cover with the screw holes aligned and refit the six board screws.[1]
  4. Reconnect the keyboard and LED connectors without twisting the LED cable, and refit the bottom cover with its six screws.[1]

Testing

[edit | edit source]
  1. Run the self test's memory test. Both ROM bars and all the RAM blocks should turn light green.[1]
  2. Run the SALT 2.05 RAM test continuously for several passes; the red failure count should stay at zero.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 Atari, Inc., 1200XL Home Computer Field Service Manual, FD100217, Rev. 01, February 1983: memory description and power supply (section 1, pp. 1-10 to 1-11); self test and SALT 2.05 RAM test with the defective RAM identifier (section 3, pp. 3-1 to 3-10); symptom checklist, console disassembly and assembly, and keyboard removal (section 4, pp. 4-1 to 4-4); parts list (section 5: U1-6, 8, 9 C060612; U7, 10 C014345; U14 C060609; U22 C060472; sockets XU1-11, XU14); component outlines and figure D (end of the scan). Hosted here as Atari 1200XL Field Service Manual.