Atari 1200XL Black Screen Repair

Unlike the later XL and XE machines, the Atari 1200XL has its power supply on the main board. The external transformer supplies 9 V AC, which the bridge rectifier CR8 (MDA990-2) rectifies and two 78M05 regulators, A1 and A2, regulate to 5 V for separate power rails.[1][2] Atari's checklist for a black or grey screen lists the regulators, the +5 V supply, the ferrite beads L4 to L8, ANTIC, CR8, the power plug, the power switch and the crystal Y1.[1] One more cause is specific to the machine: some 1200XLs show no picture with the Star Raiders cartridge, which Atari's tech tip 19 cures with a capacitor.[3]
Symptoms
[edit | edit source]- A black or grey screen with no picture.[1]
- The power-on light (LED 3) does not light. Atari's checklist for "no lights" includes the +5 V supply.[1]
- No picture only with the Star Raiders cartridge.[3]
- The screen goes blank while the machine is in use: CONTROL+F2 switches the screen display off and on.[2]
Safety
[edit | edit source]- The transformer plugs into the mains. Check it from its output plug only.
- Switch off before pulling or fitting any chip, and before soldering.
Tools and parts
[edit | edit source]- A multimeter with AC and DC voltage ranges and continuity.
- An oscilloscope, for the clock checks.
- A medium cross-head screwdriver and an IC extraction tool.
- A known-good 9 V AC transformer. The FAQ lists two Atari units for the 1200XL: C017945 (9 V AC, 31 VA, box CA017964) and C014319 (9 V AC, 15.3 VA), and notes that the smaller one is "only barely adequate" for the 400, 800 and 1200XL.[2] Atari's manual gives the 1200XL's input as 9 V AC at 31 VA.[1]
- Parts as needed: CR8 bridge rectifier MDA990-2 (C060534), A1 and A2 78M05 regulators, C39 10,000 µF 16 V (C060603), Y1 3.579545 MHz crystal (C061090), ANTIC (C012296).[1]
- For tech tip 19: a 0.001 µF NPO 50 V capacitor (Atari C014181-01).[3]
Procedure
[edit | edit source]Rule out the simple causes
[edit | edit source]- If the picture went blank while a program was running, press CONTROL+F2.[2]
- If the screen is black only with Star Raiders, go to tech tip 19 below.[3]
- Measure the transformer output at its plug with the meter on AC volts. It should be 9 V AC.[1]
Open the machine
[edit | edit source]
- Turn the computer upside down and remove the six screws that hold the bottom cover to the top cover. Lift away the bottom cover with the board and turn it right side up; unplug the keyboard and LED connectors, noting which way round the LED connector goes.[1]
- Remove the six board screws and lift out the board and the cartridge connector. Remove the eleven push rivets, separate the RF shields and remove the fish paper.[1]
- Lay the board on an insulated surface for the checks below.
Check the supply
[edit | edit source]- Check the power socket J10 (C014715) and the power switch (C061022) for continuity and good solder joints.[1]
- Connect the transformer and switch on. Measure at the input and output of A1 and A2; Atari's outline drawing gives the regulator pins as input, ground and output. Each output should be 5 V ±5 %, 4.75 to 5.25 V.[1]
- Atari's checklist names CR8, A1 and A2 for this fault. No DC at the regulator inputs points to the bridge rectifier CR8 or the 10,000 µF capacitor C39; a good input with a missing output points to the regulator or a short on its rail.[1]
- Check the ferrite beads L4 to L8 for continuity.[1]
- Measure +5 V at each custom chip, using Atari's pin assignments:
| Chip | +5 V pin | Ground pin |
|---|---|---|
| 6502 (U21) | 8 | 1 and 21 |
| ANTIC (U20) | 21 | 1 |
| GTIA (U19) | 27 | 3 |
| POKEY (U24) | 17 | 1 |
| PIA (U23) | 20 | 1 |
Check the clock and reset
[edit | edit source]
- The colour crystal Y1 is 3.579545 MHz.[1] With the oscilloscope, check for a clock on GTIA pin 28 (oscillator input) and pin 29 (FØ0 clock out).[1]
- Follow the clock to ANTIC pin 35 (fast phase 0 clock) and pin 34 (phase 0 clock), then to 6502 pin 37 (phase 0 clock in) and 6502 pin 39 (phase 2 clock out).[1]
- Check that reset is not held low. The reset pins are 6502 pin 40 (RES), ANTIC pin 36 (RST) and PIA pin 34.[1]
- If there is no clock at GTIA pin 28, check the crystal Y1, which is on Atari's list for this fault.[1]
Swap ANTIC
[edit | edit source]- Switch off. ANTIC (U20) is in a 40-pin socket, like GTIA, the CPU, the PIA and POKEY (XU19 to XU21, XU23, XU24).[1]
- Fit a known-good ANTIC (C012296) and try again. ANTIC is the one custom chip on Atari's list for a black or grey screen.[1]
Fit the Star Raiders capacitor (tech tip 19)
[edit | edit source]Tech tip 19 (15 August 1983) says that some 1200XLs display no picture when the Star Raiders cartridge is powered up, because the reset timing to the 6502 is wrong for that cartridge.[3]
- Switch off.
- Solder one lead of a 0.001 µF NPO 50 V capacitor (C014181-01) to pin 3 of U16 (74LS14) and the other lead to pin 7 of U16.[3][1]
- Atari notes that the change does not affect the troubleshooting procedures in the manual.[3]
Reassemble
[edit | edit source]- Lay the top shield upside down, place the board upside down on it, put the fish paper inside the bottom shield and lay them over the board with the adjustment holes clear. Refit the eleven push rivets.[1]
- Insert the cartridge connector, place the assembly in the bottom cover and refit the six board screws. Reconnect the keyboard and LED connectors without twisting the LED cable and refit the bottom cover.[1]
Testing
[edit | edit source]- Switch on with no cartridge. The power-on light (LED 3) should be lit and the "ATARI" logo screen should appear.[1][2]
- Press HELP and run All Tests from the self test menu.[1]
- If tech tip 19 was applied, power up with the Star Raiders cartridge and check for a picture.[3]
Related pages
[edit | edit source]- Atari 1200XL
- Atari 1200XL Troubleshooting Guide
- Atari 1200XL General Maintenance
- Atari 1200XL Capacitor Replacement Guide
- Atari 1200XL RAM Replacement
- Atari 1200XL Video Output Repair
- Atari 1200XL Field Service Manual
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 Atari, Inc., 1200XL Home Computer Field Service Manual, FD100217, Rev. 01, February 1983: pin assignments (figures 1-4 to 1-8, pp. 1-6 to 1-9) and power supply (p. 1-11); self test (section 3); symptom checklist and console disassembly and assembly (section 4, pp. 4-1 to 4-3); parts list (section 5: A1, 2; C39; CR8; J10; S1; U16; U20; sockets XU19-21, 23, 24; Y1); LED board interface (p. 1-16); component outlines at the end of the scan. Hosted here as Atari 1200XL Field Service Manual.
- ↑ 2.0 2.1 2.2 2.3 2.4 Michael Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009: section 1.4, "What is the Atari 1200XL?" (boot options and CONTROL+F2), and section 6.7, "What are the power requirements for my Atari components?" (North American AC supplies). Text at faqs.org. Community reference.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Atari, Inc., Consumer Product Service, Tech Tip 19, "No Picture on Star Raiders", Atari 1200XL CPU, 15 August 1983, in the 1200XL Home Computer Field Service Manual (section 6). Hosted here as Atari 1200XL Field Service Manual.