Jump to content

Atari 1200XL Video Output Repair

From RetroTechCollection
Atari 1200XL console, RF shield and adjustment points (FD100217 figure 4-1)
Atari's exploded view of the 1200XL, showing the colour adjustment VR1 and the audio adjustment, both reachable through the bottom cover, and, in the detail, the channel 2-3 switch and the RF modulator adjustment under the RF shield

The Atari 1200XL generates its picture in ANTIC (U20) and GTIA (U19) and sends it two ways: as composite and luminance signals on the five-pin monitor socket, and through the RF modulator A3 to the aerial socket on channel 2 or 3.[1] Atari's field service manual gives three adjustments that affect the picture, the colour control VR1, the RF modulator and the channel switch, and one modification, tech tip 12, for machines that lose sync on some televisions and monitors.[1][2]

Symptoms

[edit | edit source]

Atari's symptom checklist for picture faults:[1]

Atari 1200XL picture faults (Atari checklist, p. 4-1)
Symptom Possible causes Atari's remedy
Snowy screen Switch box, AC adaptor, channel select switch, RF modulator or cable damage Adjust or replace
Solid blue screen U24, Q3, Y1, Q2, Q4, U19 Replace
No colour or bad colour bars VR1 adjustment, U20, U2, U19, Q3, Y1, RF modulator Adjust or replace
No colour bars on TIA test U19 Replace
No grey bars RF modulator, Y1, VR1, Q3, U19 Adjust or replace
Upside-down alphanumerics or player field U20, U19, Q3 Replace

U2 appears in the colour row as printed; in the parts list U2 is one of the RAM chips.[1]

Tech tip 12 adds loss of sync on certain televisions and monitors: with high-contrast (black to white) screens the characters look very wavy, torn or ghosted, and the picture seems to enlarge.[2]

Safety

[edit | edit source]
  • Switch off and unplug the transformer before removing the RF shield or soldering.

Tools and parts

[edit | edit source]
  • A medium cross-head screwdriver and a small adjusting screwdriver.
  • Atari's SALT 2.05 diagnostic cartridge for the colour bar, grey bar and video tests.[1]
  • A frequency meter, for the alternative modulator adjustment.[1]
  • A monitor with composite input, to separate monitor-socket faults from RF faults.
  • For tech tip 12: a 6.2 kΩ ¼ W resistor (14-5622), a 150 Ω ¼ W resistor (14-5151), an 18 kΩ ¼ W resistor (14-5183) and a 1N914 diode.[2]
  • Parts as needed: GTIA (C014805), ANTIC (C012296), Q3 MPSA55 (C014809), Q2 and Q4 2N3906, Y1 3.579545 MHz crystal (C061090).[1]

Procedure

[edit | edit source]

Check the outputs

[edit | edit source]
Atari 1200XL monitor socket and LED board pin assignments (FD100217 figure 1-13)
Atari's figure of the 1200XL monitor socket
  1. Check the channel switch on the machine against the television's channel, and the switch box and RF cable. Atari's checklist puts these first for a snowy picture.[1]
  2. Connect a monitor to the five-pin DIN monitor socket. Atari's pin assignments are pin 1 luminance, pin 2 ground, pin 3 audio output, pin 4 colour (composite) video and pin 5 not used.[1] The 1200XL has no separate chrominance signal on pin 5.[3]
  3. If the picture is good on the monitor and bad only on the television, the fault is in the RF modulator, its adjustment or the cable.[1]

Run the SALT video tests

[edit | edit source]
  1. Insert the SALT 2.05 cartridge and switch on. On a 1200XL, "ERR" in the ROM row of the header and a red screen are not failures.[1]
  2. Type A and RETURN for the Any Video test. The screen should show a black background with eight vertical bars, half narrow and half wide, a horizontal bar across the top whose shade changes from left to right, and two Vs at the right, one normal and one inverse. The test also checks ANTIC for pattern sensitivity.[1]
  3. Type G and RETURN for the Grey Bar test. It checks that GTIA generates luminance levels 0, 1 and 2. Eight equal horizontal bars should run from black at the top to white at the bottom in even steps, with a thin white line just above the top bar and no colour anywhere. Leave it running for at least 60 seconds and watch for flashing colour or shifting bars.[1]
  4. Type C and RETURN for the Colour Bar test: a 15-colour rainbow above a reference bar and a single colour bar below it.[1]

Adjust the colour (VR1)

[edit | edit source]
  1. With the Colour Bar test running, adjust VR1 until the bars directly above and below the reference bar are the same colour, goldenrod. Atari says the adjustment can be made through the top or bottom cover; figure 4-1 shows its position.[1]
  2. Leave the test on for at least 60 seconds to catch intermittent faults, such as a bar that changes colour or blanks out. Minor glitches at the edges of the bars are acceptable.[1]

Adjust the RF modulator

[edit | edit source]
  1. Open the machine: remove the six bottom cover screws, lift away the bottom cover with the board, unplug the keyboard and LED connectors, remove the six board screws and lift out the board and cartridge connector.[1]
  2. Remove the eleven push rivets and the top RF shield to reach the modulator adjustment.[1]
  3. With the Colour Bar test running, adjust the modulator for a correct colour bar screen.[1]
  4. Alternatively, connect a frequency meter to the RF output jack of the modulator (A3), set the channel switch SW3 to channel 3 and adjust the modulator to 61.25 MHz.[1] Atari specifies channel 3 as 61.25 MHz ±0.5 MHz and channel 2 as 55.25 MHz, with an output of 1 to 2 mV into 75 Ω and the sound carrier at 4.5 MHz.[1]
  5. Refit the shield, with the fish paper inside the bottom shield and the adjustment holes clear, and the eleven push rivets.[1]

Fit the sync modification (tech tip 12)

[edit | edit source]

Atari's tech tip 12 (16 June 1983) applies only to machines that show the sync fault.[2]

Tech tip 12 changes
Position Remove Fit
R22 4.3 kΩ ¼ W (14-5432) 6.2 kΩ ¼ W (14-5622)
R188 910 Ω ¼ W (14-5911) 1N914 diode (31-1N914), cathode closest to the bridge rectifier
R163 100 Ω ¼ W (14-5101) 150 Ω ¼ W (14-5151)
R145 Unused position 18 kΩ ¼ W (14-5183)

[2]

  1. Open the machine and remove the RF shield as above.[1]
  2. Make the four changes in the table, fitting the diode at R188 with its cathode towards the bridge rectifier CR8.[2][1]
  3. Atari notes that the changes do not alter the troubleshooting procedures in the manual.[2]

Change parts

[edit | edit source]
Atari 1200XL 6502, ANTIC and GTIA pin assignments (FD100217 figures 1-4 to 1-6)
Atari's pin assignments for the 6502, ANTIC and GTIA
  1. GTIA (U19) and ANTIC (U20) are in 40-pin sockets; swap them for known-good parts according to the checklist row.[1]
  2. GTIA's video outputs are pin 21 (colour), pins 22, 23, 24 and 31 (luminance 0 to 3) and pin 25 (composite sync); its colour delay input is pin 17.[1]
  3. Q3 (MPSA55), Q2 and Q4 (2N3906) and the crystal Y1 are soldered parts named in the checklist rows.[1]

Reassemble

[edit | edit source]
  1. Lay the top shield upside down, place the board upside down on it, put the fish paper inside the bottom shield and lay them over the board with the adjustment holes clear. Refit the eleven push rivets.[1]
  2. Insert the cartridge connector, place the assembly in the bottom cover and refit the six board screws. Reconnect the keyboard and LED connectors without twisting the LED cable and refit the bottom cover.[1]

Testing

[edit | edit source]
  1. Run the SALT Any Video, Grey Bar and Colour Bar tests and check each screen against the descriptions above, leaving the bar tests on for at least 60 seconds.[1]
  2. After tech tip 12, check a high-contrast screen on the television or monitor that showed the fault.[2]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 Atari, Inc., 1200XL Home Computer Field Service Manual, FD100217, Rev. 01, February 1983: GTIA pin assignments (figure 1-6), RF modulator specification (p. 1-10) and monitor interface (figure 1-13, p. 1-16); SALT 2.05 header, Colour Bar, Any Video and Grey Bar tests (section 3, pp. 3-3 to 3-8); symptom checklist, console disassembly and assembly, RF modulator and colour adjustments and figure 4-1 (section 4, pp. 4-1 to 4-4); parts list (section 5). Hosted here as Atari 1200XL Field Service Manual.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Atari, Inc., Consumer Product Service, Tech Tip 12, "Color Burst/Video Sync", Atari 1200XL Computer, 16 June 1983, in the 1200XL Home Computer Field Service Manual (section 6). Hosted here as Atari 1200XL Field Service Manual.
  3. ↑ Michael Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009, section 1.4, "What is the Atari 1200XL?". Text at faqs.org. Community reference.