Atari 1200XL Sound Repair

The Atari 1200XL has no speaker of its own. POKEY (U24) generates all four sound channels, and the key clicks and system beeps that the 400 and 800 played through an internal speaker are heard from the television or monitor instead.[1][2] The sound reaches the monitor socket as an audio signal and the television through the RF modulator on a 4.5 MHz sound carrier.[1] Atari's field service manual has an AUDIO adjustment for this, and its tech tip 15 replaces two capacitors in the audio oscillator of machines whose sound drifts.[1][3]
Symptoms
[edit | edit source]- Tones missing during sound or games. Atari's checklist gives U24, L11 and L12, and the audio adjustment.[1]
- Poor sound or no sound on the television, or sound that has to be readjusted again and again or cannot be adjusted at all (tech tip 15).[3]
- No key clicks: CONTROL+F3 switches the key click on and off.[2]
Safety
[edit | edit source]- Switch off and unplug the transformer before opening the case or soldering.
Tools and parts
[edit | edit source]- A medium cross-head screwdriver and a small adjusting tool for the AUDIO adjustment.
- A monitor or amplifier that can take audio from the monitor socket.
- For tech tip 15: two 820 pF 25 V polystyrene capacitors (Atari C018261, alternate C010821).[3]
- If POKEY is at fault: a known-good POKEY (C012294) for the socket at U24.[1]
Procedure
[edit | edit source]Check the key click and the self test
[edit | edit source]- If only the key click is missing, press CONTROL+F3.[2]
- Remove any cartridge, switch on and press HELP at the logo. Select AUDIO VISUAL with SELECT and press START. A tune of six notes plays on each of the four voices in turn, voice 1 to voice 4, with the note shown on a music staff and the voice number under it.[1]
- Note whether every voice plays and whether the fault is in all four voices or only some.
Separate the RF sound from the audio output
[edit | edit source]
- Connect a monitor or amplifier to the monitor socket: audio output is pin 3 and ground pin 2.[1]
- If the sound is good from the monitor socket but poor, drifting or missing on the television, the fault is in the RF sound path: go to the AUDIO adjustment and tech tip 15 below.[1][3]
- If the sound is missing or wrong at the monitor socket as well, go to POKEY below.
Adjust the AUDIO control
[edit | edit source]- Find the AUDIO adjustment from figure 4-1. Atari says the adjustment can be made through the top or bottom cover.[1]
- The checklist pairs the audio adjustment with L11 and L12; in the parts list L11 is the adjustable inductor (C010323) and L12 a 2 µH inductor.[1] Atari gives the position of the adjustment and the 4.5 MHz sound carrier frequency, but no step-by-step procedure.[1]
- With the Audio Visual test playing through the television, turn the adjustment slowly for the clearest sound.
Replace C96 and C97 (tech tip 15)
[edit | edit source]Atari's tech tip 15 (7 June 1983) traces audio frequency drift to components that do not meet specification and replaces the ceramic capacitors in the audio oscillator circuit with polystyrene ones. Perform it only on machines that show the drift.[3]
- Open the machine: remove the six bottom cover screws, lift away the bottom cover with the board, unplug the keyboard and LED connectors, remove the six board screws and lift out the board. Remove the eleven push rivets, separate the RF shields and remove the fish paper.[1]
- Remove C96 and C97, ceramic 820 pF 25 V (C061336-03).[3]
- Fit polystyrene 820 pF 25 V capacitors (C018261; the alternate is C010821) in their place.[3]
- Reassemble: shields and fish paper with the adjustment holes clear, eleven push rivets, board and cartridge connector in the bottom cover with six screws, keyboard and LED connectors, bottom cover.[1]
- Readjust the AUDIO control as above. Atari notes that the change does not affect the troubleshooting procedures in the manual.[3]
Change POKEY
[edit | edit source]- POKEY's audio output is pin 37; its supply is pin 17 (+5 V) and pin 1 (ground).[1]
- POKEY sits in a 40-pin socket. Switch off and swap it for a known-good part, fitted the same way round.[1]
- Atari's checklist also names U24 for a solid blue screen and for keyboard faults.[1]
Testing
[edit | edit source]- Run the self test's Audio Visual test and listen to all four voices on the television and at the monitor socket.[1]
- After tech tip 15, leave the machine running for a while and check that the television sound stays clear without readjustment.[3]
- Press a few keys to check the key click, and CONTROL+F3 to check that it can be turned off and on.[2]
Related pages
[edit | edit source]- Atari 1200XL
- Atari 1200XL Troubleshooting Guide
- Atari 1200XL Capacitor Replacement Guide
- Atari 1200XL Video Output Repair
- Atari 1200XL Field Service Manual
- Atari 800XL Sound Repair
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 Atari, Inc., 1200XL Home Computer Field Service Manual, FD100217, Rev. 01, February 1983: POKEY pin assignments (figure 1-7), RF modulator specification (p. 1-10) and monitor interface (figure 1-13, p. 1-16); self test Audio Visual test (section 3, p. 3-2); symptom checklist, console disassembly and assembly, sound adjustment and figure 4-1 (section 4, pp. 4-1 to 4-4); parts list (section 5: L11, L12, U24, socket XU24). Hosted here as Atari 1200XL Field Service Manual.
- ↑ 2.0 2.1 2.2 2.3 Michael Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 29 November 2009, section 1.4, "What is the Atari 1200XL?" (sound through the television, CONTROL+F3). Text at faqs.org. Community reference.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Atari, Inc., Consumer Product Service, Tech Tip 15, "Audio Frequency (Sound) Drift", Atari 1200XL Computer, 7 June 1983, in the 1200XL Home Computer Field Service Manual (section 6). Hosted here as Atari 1200XL Field Service Manual.