Jump to content

Atari 410 Motor Control Repair

From RetroTechCollection
Atari 410 Program Recorder
A later Atari 410 Program Recorder, the version without a carrying handle (photo: Bilby, CC BY 3.0)

The motor of the Atari 410 Program Recorder runs from its own mains supply and is switched by two transistors: Q102, driven by the computer's motor control line on SIO pin 8, and Q101, which passes the rectified supply to the motor. When the tape will not start for a load, will not stop, or runs slowly, Atari's 410 Program Cassette Recorder Field Service Manual gives voltages at three points along this path and a table of causes for a slow motor.[1] The manual describes the Transtek-built recorder (final assembly CA015368). Atari's tech tip 9 lists component values that differ on Chelco-built units, so compare your board with the schematic before taking readings.[1][2]

Symptoms

[edit | edit source]
  • PLAY is down but the tape does not move when the computer starts a load or save, although REWIND and ADVANCE wind the tape.[1]
  • The tape moves as soon as PLAY is pressed after a cold start in BASIC. Atari's tech tip says it should not move until the computer turns the motor on.[3]
  • The tape runs slowly, or the motor speed wavers. Atari lists the motor, the drive roller and stretched belts as causes of flutter and wow.[1]

Before opening the recorder, check the computer's side. After a cold start, POKE 54018,52 should start the motor and POKE 54018,60 should stop it. If the tape runs regardless, Atari's tech tip points at the computer's motor control transistor, Q102 in the 400 and Q107 in the 800.[3] A recorder plugged in through another SIO device is a known source of trouble; connect it directly to the computer.[3] Mechanical faults (belts, a stiff mechanism) are covered in the Atari 410 Maintenance Guide.

Safety

[edit | edit source]

Warning: the 410 has a mains transformer inside and mains voltage is present whenever it is plugged in. Atari's operator's manual and the Skematiks service notes both warn of this.[4][5] The readings below are taken with the recorder powered; keep fingers and probes away from the mains lead, the transformer primary and its connections, and unplug the recorder from the wall before touching anything with a soldering iron.

Tools and parts

[edit | edit source]
Motor circuit parts (FD100004 p. 6-1)
Ref Part Atari number
Q101 Transistor 2SA755 FC100023
Q102 Transistor 2SC1815 FC100024
CR104, CR105 Diode MR501 C014398
C127 Electrolytic 2200 µF 16 V C014373
C126 Electrolytic 220 µF 16 V FC100018
L101 Inductor 100 µH FC100020
S101, S102 Switch FC100021
R134 1 kΩ, 1/4 W 14-5102
R135 470 Ω, 1/4 W 14-5471
R136 27 kΩ, 1/4 W 14-5273

[1]

How the circuit works

[edit | edit source]
Atari 410 motor control circuit (FSM figure 7-1)
The motor section of Atari's 410 schematic. CR104 and CR105 rectify the transformer output; S102 closes in PLAY; Q102, driven from SIO pin 8 through R136, or the REW/FFWD switch S101, turns Q101 on; Q101 feeds the motor through L101, with C127 and C126 as reservoir and filter

The motor control line, pin 8 of the serial bus connector, is low when the system is switched on. In the computer it comes from Q102 on the 400 motherboard or Q107 on the 800. In the recorder it drives Q102, which in turn controls Q101.[1] On the schematic the transformer output is full-wave rectified by CR104 and CR105 and reaches Q101 through the primary motor control switch S102, which closes when PLAY or PLAY and RECORD are pressed. Q101's base is held off by R134 (1 kΩ) and pulled on through R135 (470 Ω) either by Q102, whose base is fed from pin 8 through R136 (27 kΩ), or by the REW/FFWD switch S101. Q101's output goes to the motor through L101 (100 µH), with C127 (2200 µF) and C126 (220 µF).[1] The 410 takes its motor control power, +5 V, from the computer it is connected to.[1]

Procedure

[edit | edit source]

Step 1: measure the motor control path

[edit | edit source]

Take these readings with a DC voltmeter referenced to I/O cable pin 4 (ground), with PLAY pressed so that S102 is closed. "Static" means the computer has not turned the motor on; "running" means it has (for example after POKE 54018,52). Atari allows ±0.5 V with the diagnostic tape running.[1][3]

Motor control readings (FD100004 p. 4-2)
Point Static Running
SIO pin 8, from the computer 0.80 V 4.80 V
Collector of Q102 4.95 V 1.65 V
Collector of Q101 0.00 V 5.95 V

[1]

Work along the path in signal order. The parts to check at each stage are those that sit between the two test points on Atari's schematic.[1]

  1. Measure pin 8. If it does not rise to about 4.8 V when the motor is turned on, the signal is not reaching the recorder: check the computer's motor control transistor (see above) and the I/O cable.[1][3]
  2. Measure the collector of Q102. It should fall from about 4.95 V to about 1.65 V when pin 8 rises. If it does not, the parts between are R136 and Q102.[1]
  3. Measure the collector of Q101. It should rise from 0 V to about 6 V. If Q102 switches but Q101's collector stays at 0 V, check that S102 closes when PLAY is down, then check R135, R134 and Q101.[1]
  4. If PLAY, REWIND and ADVANCE all fail to move the tape, measure the supply side: the slow-motor checks below start at the emitter of Q101.[1]

Step 2: slow or uneven motor

[edit | edit source]

Atari's slow-motor table, in order:[1]

  1. Put the scope on the emitter of Q101. The waveform should be full-wave rectified. Atari lists Q101 against this check, and the rectifiers CR104 and CR105 if Q101 does not have a full wave.
  2. Check the base of Q101: it should be a steady voltage. Atari lists Q101 against this check.
  3. Excessive ripple can come from the computer's motor control signal, from Q102 on the 400 or Q107 on the 800.
  4. If the voltage is higher than it should be, replace Q102 (Atari's table names its base or collector).
  5. If all of these check out, replace the motor.

Before replacing the motor, clean the drive roller and check the belts; Atari lists both, with the motor, as causes of slow sound and errors.[1]

Step 3: switches

[edit | edit source]
  • S102 must close for the motor to run in PLAY. It need not be closed in REWIND or ADVANCE, which use S101.[1]
  • S100, the RECORD/PLAYBACK switch, causes occasional problems, usually dirty contacts, which can be cleaned with contact cleaner.[1] See Switch and Potentiometer Repair.

Step 4: replacing parts

[edit | edit source]
  1. Unplug the recorder from the wall and from the computer.
  2. Desolder the faulty part, noting the orientation of transistors, diodes and electrolytics against the board and the schematic.
  3. Fit the replacement from the table above. Q101 is a PNP 2SA755 and Q102 an NPN 2SC1815, according to Atari's parts list.[1]
  4. Check your work for cold joints and broken wires before powering up; Atari asks for these to be checked whenever a fault is intermittent.[1]

Testing

[edit | edit source]
  1. Repeat the readings in step 1: 0.80 V and 4.80 V at pin 8, 4.95 V and 1.65 V at Q102's collector, 0.00 V and 5.95 V at Q101's collector.[1]
  2. After a cold start, check that pressing PLAY alone does not move the tape, that POKE 54018,52 starts it and that POKE 54018,60 stops it.[3]
  3. Run Atari's recorder test: load the test tape with CLOAD (about 45 seconds of tape), RUN it and follow the screen, saving to and reloading from a blank tape. Two load errors in a row mean the recorder is still faulty.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 Atari, Inc., 410 Program Cassette Recorder Field Service Manual, FD100004, May 1982: introduction (p. v), maintenance areas (pp. 1-1 and 1-2), motor control operation (pp. 2-1 and 2-2), recorder test (pp. 3-1 and 3-2), motor readings and slow motor table (p. 4-2), switch maintenance (p. 4-3), parts list (p. 6-1), schematic (figure 7-1, "410 Differences", p. 7-1). Hosted here as File:Atari 410 Program Cassette Recorder Field Service Manual FD100004.pdf.
  2. ↑ Atari, Inc., Consumer Product Service, Tech Tip 9, "410 Cassette Recorders that register #143 error codes", 9 February 1983: component values to check on Chelco-built units, which Transtek units already have. Bound into the hosted copy of File:Atari 410 Program Cassette Recorder Field Service Manual FD100004.pdf (PDF pp. 22 to 24).
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Atari, Inc., Consumer Product Service, Tech Tip, "ATARI 410 Recorder: 138, 140, and 143 Errors", 17 November 1982, servicer items 2 (peripheral connection) and 5 (410 motor control). Bound into the hosted copy of File:Atari 410 Program Cassette Recorder Field Service Manual FD100004.pdf.
  4. ↑ Atari, Inc., ATARI 410 Program Recorder operator's manual, C014810 Rev. 2, 1979: safety note. Hosted here as File:Atari 410 Program Recorder Operator's Manual.pdf.
  5. ↑ Skematiks, covering notes to schematic 7S-AT410-3, November 1983: "CAUTION, 117VAC is present during servicing". Internet Archive item atari-410-schematic-a-skematiks. Third-party service notes.