Jump to content

Atari 520ST Video Output Repair

From RetroTechCollection
Rear ports of original Atari 520ST
Back panel of a short-case 520ST-series machine. The round 13-pin monitor socket J6 is in the middle, between the television output and the printer port (photo: Blake Patterson, CC BY 2.0).

The Atari 520ST sends its picture to the 13-pin monitor socket through a short chain on the main board: the video Shifter U31 produces three digital outputs for each colour, a resistor network sums each set into an eight-level signal, and an emitter-follower transistor for each colour drives the monitor socket J6. Monochrome has its own output and buffer.[1] The same schematic covers the 260ST, and the 520ST+ and 520STM share the short case and its main board.[2]

Faults in this chain give a missing colour, coarse steps in brightness or no monochrome picture. Atari's manual and Howard W. Sams's service data both give a procedure that follows the signal from the Shifter to the socket with an oscilloscope.[3][4]

Symptoms

[edit | edit source]
Picture faults and where to look
Symptom Likely place Source
One primary colour missing That colour's buffer transistor or summing network, or the Shifter Atari, SAMS
Primaries present, secondary colours missing or wrong Shifter Atari
Coarse steps in brightness instead of a smooth ramp Shifter, or a short on one of that colour's three outputs Atari
No picture on a monochrome monitor Shifter pin 30, buffer Q2, R42, the monitor socket SAMS
No picture on a colour monitor Shifter or Glue; L18 if all three colours are missing SAMS
Specks or lines RAM; the Shifter if the RAM tests good Atari
Flicker that starts after the machine has warmed up Shifter clock; see below Atari Benelux

Sources: Atari's manual,[3] SAMS[4] and Atari Benelux.[5] Atari notes that too low a brightness setting on the monitor can make the eight levels of a colour look like four.[3]

A blank screen with no picture at all on either kind of monitor is usually not this circuit; work through the dead-unit procedure on the Atari ST Troubleshooting Guide first. Check the monitor and its cable with another machine before opening the computer.

Safety

[edit | edit source]

The main board runs at low voltage, but the computer's external supply is mains powered; see Atari 520ST Power Supply Repair. If you open the monitor, read the CRT Discharge Procedure first.

Tools and parts

[edit | edit source]
  • An oscilloscope. A multimeter alone cannot show the eight-step staircase.[3]
  • Atari's diagnostic cartridge, if you have one, for its colour test. Without it, the BASIC program below from SAMS draws red, green and blue bars.[3][4]
  • Replacement parts from the schematic: 2N3904 transistors (Q2–Q5), 1N914 diodes (CR1–CR6), and resistors of the values below.[1]
The colour chain on the 520ST (schematic C070231)
Colour Shifter pins (bits 2, 1, 0) Summing resistors Diode to buffer Buffer Base bias Emitter resistor Series resistor J6 pin
Red 27, 28, 29 R59 3.6 kΩ, R60 7.5 kΩ, R61 15 kΩ CR6 Q5 R66 5.1 kΩ, R87 3.6 kΩ R52 100 Ω R117 27 Ω 7
Green 24, 25, 26 R56 3.6 kΩ, R57 7.5 kΩ, R58 15 kΩ CR5 Q4 R51 5.1 kΩ, R50 3.6 kΩ R49 100 Ω R116 27 Ω 6
Blue 21, 22, 23 R53 3.6 kΩ, R54 7.5 kΩ, R55 15 kΩ CR4 Q3 R48 5.1 kΩ, R47 3.6 kΩ R46 100 Ω R115 27 Ω 10
Monochrome 30 – – Q2 R45 1 kΩ, R44 1 kΩ R43 100 Ω R42 27 Ω 11

Sources: the schematic for the parts and pins;[1] J6 pin numbers from Atari's monitor port figure.[3] The buffers' collectors take +5 V through the choke L18; Q2's takes +5 V through L17.[1]

Atari 520ST Shifter colour outputs (schematic C070231 sheet 2)
The Shifter U31 and its summing resistors on Atari's schematic. Each colour's three outputs meet at a node pulled up by R62, R63 or R64 and clamped by CR1, CR2 or CR3 when BLANK is low.

Procedure

[edit | edit source]

Open the machine

[edit | edit source]

Atari's sequence for the short case:[6]

  1. Unplug the power supply and the monitor. Turn the computer upside down and remove the six screws from the bottom case.
  2. Turn it upright, lift off the top case and unplug the keyboard connector at the right front of the board.
  3. Remove the three screws at the front edge of the board and the three at the rear, reached through holes in the shield, and lift the board assembly out of the bottom case.
  4. Straighten the ten twist tabs and lift off the top shield. Reconnect the keyboard, supply and monitor to run the board on the bench.

Show a test pattern

[edit | edit source]
  1. With the diagnostic cartridge, run its colour test: seven bands (red, green, blue, cyan, magenta, yellow and white), each in eight levels of brightness.[3]
  2. Without the cartridge, load ST BASIC and run SAMS's program, which should draw a red, a green and a blue vertical bar on an RGB monitor:[4]
10 Z=10
20 C=2
30 FOR X=100 TO 300 STEP 100
40 LINEF X,0,X,166
50 COLOR 1,C,1
60 C=C+1
70 FILL Z,0
80 Z=Z+100
90 NEXT X
100 GOTO 100

One colour missing

[edit | edit source]

Follow the missing colour with the oscilloscope. Atari's method is to look for the eight-step staircase at the buffer transistor and then work forwards or backwards from there; SAMS gives the same order point by point.[3][4]

  1. Check the video waveform at the anode of that colour's BLANK diode: CR1 for red, CR2 for green, CR3 for blue, as SAMS numbers them. If it is missing, check the Shifter's three outputs for that colour and the values of the three summing resistors.[4][3]
  2. Check the waveform at the emitter of the buffer: Q5 for red, Q4 for green, Q3 for blue. If it is missing, check the transistor and the parts around it: the series diode, the two bias resistors and the 100 Ω emitter resistor.[4][1]
  3. If it is present at the emitter, check it at the monitor socket: J6 pin 7 for red, pin 6 for green, pin 10 for blue. If it is missing there, check the 27 Ω series resistor (R117, R116 or R115).[4]
  4. If it is present at J6, check the socket's joints, the cable and the monitor.[4]

SAMS's schematic marks about 1.9 V on the buffers' bases and 1.2 V on their emitters on a working machine.[4]

Atari 520ST video output buffers (schematic C070231 sheet 3)
The three colour buffers Q5, Q4 and Q3 and the monochrome buffer Q2 on Atari's schematic (version with modulator), with the 27 Ω resistors R117, R116 and R115 to the monitor socket.

All three colours missing

[edit | edit source]
  1. If the waveforms are present at the diodes but missing at all three emitters, check for +5 V at the collectors of Q3, Q4 and Q5. If it is missing, check the choke L18.[4]
  2. If the Shifter's colour outputs (pins 21–29) are themselves missing, check the Shifter U31 and the Glue U12.[4]

Coarse steps or wrong secondary colours

[edit | edit source]
  1. Coarse steps: check each of the three Shifter outputs for that colour and its summing resistor for a short. If none is found, replace the Shifter.[3]
  2. Primaries present but secondaries missing or wrong: replace the Shifter.[3]

No monochrome picture

[edit | edit source]

The monochrome monitor tells the machine it is connected by pulling the monochrome-detect line, J6 pin 4, low; the MFP reads it at power-up and the Shifter then produces the high-resolution picture on pin 30.[3]

  1. Check the waveform at Shifter pin 30. If it is missing with the monochrome monitor connected, check the Shifter and the Glue.[4]
  2. Check the waveform at the emitter of Q2. If it is missing, check Q2 and the parts around it.[4]
  3. Check the waveform at J6 pin 11. If it is missing there but present at Q2's emitter, check R42.[4]

Flicker after warming up

[edit | edit source]

Atari Benelux found that some earlier ST and ST+ computers developed a flickering picture once the Shifter reached a certain temperature. Replacing the Shifter or the memory controller cured it only for a while. Atari's fix is a 5–10 pF capacitor soldered between Shifter pin 39, its 16 MHz clock output, and ground; the bulletin says later production fitted it at the factory as C108.[5][1] On the revision M schematic the designator C108 belongs to a different part, so identify the capacitor by its connection to pin 39, not by its number.[1]

Testing

[edit | edit source]
  • Run the colour test or the SAMS program again and check every colour band in all eight levels.[3][4]
  • Atari's figures for the monitor signals: red, green and blue 0–1.0 V peak to peak into 75 Ω; monochrome 1.0 V peak to peak into 75 Ω; horizontal and vertical sync TTL level, negative, 3.3 kΩ.[3]
  • Refit the shield and the top case and test again; Atari recommends a final test once the machine is back in its case.[6]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Atari (Japan) Corporation, Schematic Diagram (520ST/260ST), drawing C070231, revision M (April 1986), covering assemblies CA070052-001 to -005 with and without the television modulator. Sheet 2: Shifter U31, colour outputs and summing resistors R53–R61, pull-ups R62–R64, BLANK diodes CR1–CR3, MONO output on pin 30. Sheet 3: video buffers Q5, Q4, Q3 and Q2, their bias and emitter resistors, R115–R117, L18 and the monitor socket J6. Hosted here: File:Atari 520ST Schematic C070231.pdf.
  2. ↑ "Atari 520ST, 260ST, 520ST+, 520STM, 130ST und ST Junior", atari-computermuseum.de (in German), revised 26 June 2024: the short-case models and their common main board, C070243.
  3. ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 3.13 Atari Corporation, 520ST/1040ST Computer Field Service Manual, C026118-002 Rev B (3.6), January 1987. Monitor input levels and figure 1.4, the monitor port (PDF p. 18); the dead-unit procedure, including the monochrome-detect check (PDF pp. 29–30); the diagnostic cartridge colour test (PDF p. 33); its "Symptoms and fixes" (PDF p. 34); the symptom checklist (PDF p. 51). Hosted here: File:Atari 520ST and 1040ST Computer Field Service Manual.pdf.
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 SAMS Computerfacts CSCS12: Atari Model 520ST, Howard W. Sams & Co., June 1986, ISBN 0-672-08974-2. Video schematic with DC voltages and waveforms (printed p. 5, PDF p. 7); troubleshooting, "Video" and "Color", with the colour-bar test program (p. 26, PDF p. 28). Internet Archive.
  5. ↑ 5.0 5.1 Atari (Benelux) B.V., Information Technique No. 13: flicker on earlier ST and ST+ computers once the Shifter warms up, and the 5–10 pF capacitor between Shifter pin 39 and ground. Hosted here: File:Atari Benelux technical bulletin 013 - ST screen flicker.pdf.
  6. ↑ 6.0 6.1 Atari Corporation, 520ST/1040ST Computer Field Service Manual, section 4, 520ST disassembly (pp. 4.3–4.4, PDF pp. 48–49). Hosted here: File:Atari 520ST and 1040ST Computer Field Service Manual.pdf.