Atari 800 RAM Replacement

The Atari 800 holds its RAM on plug-in modules in the slots behind the operating system module, and the Atari 400 uses the same 8K (CA014801) and 16K (CA014802) RAM boards, one board inside its module assembly.[1] Each board carries eight RAM chips, Z505 to Z512 (Atari C014331), with a 74LS10 (Z501), a 74LS244 (Z502) and two 74LS158 multiplexers (Z503 and Z504); the parts list includes sockets for the board's chips.[1] Sams lists the RAM chips on the 16K board as MK4116 types.[2] Atari's SALT II diagnostic cartridge identifies the failing board and, on a stable failure, the failing chip.[1]
Symptoms
[edit | edit source]- "SYSTEM FAILURE" on the screen when the SALT II cartridge starts, which Atari says means the lower RAM is not working.[1]
- Red 1s in the SALT II RAM test.[1]
- The SALT RAM test reports less memory than is fitted.[1]
- A green or yellow screen. Atari's flowchart for this asks first whether a RAM module is faulty, checking the lowest RAM slot first, before swapping the operating system ROMs A401 to A403 on the personality board and then A303, Z303 and Z304.[1]
Safety
[edit | edit source]- Switch the computer off before removing or inserting any module or chip.
- Handle the boards with static precautions, as Atari's disassembly notes require.[1]
Tools and parts
[edit | edit source]- Atari's SALT II diagnostic cartridge.[1]
- A known-good RAM module for swapping.[1]
- An IC extraction tool, and replacement RAM chips (Atari C014331; MK4116 on the 16K board according to Sams).[1][2]
- A pair of 74LS158s (C014345) of the same manufacturer and date code, and a 74LS244 (C014313), if the test points to them.[1]
- For the edge connectors: isopropyl alcohol or ZEP safety solvent, a dust-free cloth, a board cleaning brush and contact lubricant (Atari names Libriplate DS-ES).[1]
Procedure
[edit | edit source]Take out the RAM modules
[edit | edit source]- Switch the power off and open the cartridge door.[1]
- Turn the cartridge door clamps towards the outside of the console. Lift the cartridge door assembly a quarter of an inch, pull it towards you and lift it off.[1]
- Lift out the RAM modules, and the ROM module if needed. Turn the door clamps back afterwards.[1]
Start SALT II
[edit | edit source]- Insert the SALT II cartridge in the left cartridge slot and switch on. The SALT header shows that the CPU, the operating system ROMs and the lower RAM are working.[1]
- If "SYSTEM FAILURE" appears, the lower RAM is not working. Switch off, replace the front RAM module with a known-good one and move the suspect module to the number 2 RAM slot, the third slot behind the operating system, so that SALT II can test it later. Switch on again.[1]
- If RAM and ROM modules have been swapped and the fault remains, swap the CPU board. Once the fault is isolated to a board, clean its edge connector and retest it (see below).[1]
Run the RAM test
[edit | edit source]- Type D and RETURN for Display Options, then E and RETURN for the error table, then S for a single test or C for continuous testing.[1]
- Type R and RETURN. When asked how many 8K blocks to check (at most five), type 1 for each 8K module and 2 for each 16K module, then RETURN.[1]
- The white four-digit number at the bottom right counts tests and the red number above it counts failures; failures show as red 1s in the matrix. Press the space bar to stop; the RAM test finishes its current pass first.[1]
- If the amount of RAM reported is less than you entered, either the machine has less RAM than expected or a module is faulty.[1]
Find the module
[edit | edit source]- If the pattern keeps changing, one of the modules probably has a faulty pair of 74LS158s (Z503 and Z504). Replace them with chips of the same manufacturer and date code.[1]
- To find which module, switch off, remove one module and start the test again from Display Options.[1]
- If the pattern is stable, read line B, columns 4 to 7, against Table 3-2.[1]
| Indicator in line B | Failing block |
|---|---|
| B4 | 1st 8K block |
| B5, or B4 and B5 | 2nd 8K block |
| B6, or B4 and B6 | 3rd 8K block |
| B5 and B6, or B4, B5 and B6 | 4th 8K block |
| B7, or B4 and B7 | 5th 8K block |
Find the chip
[edit | edit source]- Compare rows D and E. If they differ in one column, Table 3-3 gives the chip. If more than one column differs, replace the 74LS244 (Z502) and retest.[1]
| Column | 8K board | 16K board |
|---|---|---|
| D0 | Z512 | Z512 |
| D1 | Z511 | Z511 |
| D2 | Z510 | Z510 |
| D3 | Z508 | Z509 |
| D4 | Z509 | Z508 |
| D5 | Z507 | Z507 |
| D6 | Z505 | Z506 |
| D7 | Z506 | Z505 |
The order differs between the 8K and 16K boards for D3, D4, D6 and D7, so check which board is fitted.[1]
Check the supplies on the board
[edit | edit source]With the module fitted and the power on, Sams gives 5.1 V at test point 1, 11.8 V at test point 5 and −5.0 V at test point 6 on the 16K RAM board (see the photograph).[2] If any is missing on every module, see Atari 800 Power Supply Repair.
Replace the chip
[edit | edit source]- Switch off and remove the module. Lift out the chip that Table 3-3 names and fit the replacement the same way round, using Sams's pin 1 markings.[1][2]
Clean and lubricate the edge connector
[edit | edit source]- Inspect the contacts for flux, dirt, foreign material and badly scored fingers.[1]
- Clean both sides of the fingers with the dust-free cloth moistened with solvent, and avoid touching them afterwards.[1]
- If corrosion or residue remains, brush the contacts firmly with the solvent-moistened board cleaning brush, four to six strokes, without touching the rest of the board, then clean them with the cloth again.[1]
- Apply an even coat of lubricant to the fingers on both sides with an acid brush, thick enough to protect them from corrosion, and keep it off the rest of the board.[1]
On the 400
[edit | edit source]The 400 has a single RAM board inside its module assembly. If "SYSTEM FAILURE" appears, switch off, swap the RAM board for a known-good one and switch on; if the SALT header then appears, the board that was removed is probably faulty.[1] To reach it:[1]
- Remove the four bottom cover screws, unhook the top cover from the keyboard, open the cartridge door and lift the top cover off.
- Remove the keyboard screw, lift the left end of the keyboard and disconnect its ribbon cable.
- Remove the power supply: disconnect the RF cable, remove the two screws, pull the board a quarter of an inch away from the casting, lift out the interlock plunger and lift the board off the motherboard pins. See Atari 400 Power Supply Repair.
- Disconnect and remove the speaker assembly and lift the module assembly out of the bottom cover.
- Close and latch the cartridge door, set the module on its back, remove the eight screws from the bottom shield and lift off the shield.
- Lift the motherboard assembly out of the aluminium casting and unplug the RAM board.
- To refit, insert the RAM and CPU boards with their component sides facing away from you, lower the motherboard into the inverted casting with the CPU board in its guides, and refit the lower shield with its eight screws.
Testing
[edit | edit source]- Run the SALT II RAM test continuously; the red failure counter should stay at zero.[1]
- Atari's tech tip 10 uses a burn-in of at least 12 hours on the continuous RAM test of SALT 2.05 to find intermittent faults.[3]
- Remove SALT and switch on. The ATARI COMPUTER - MEMO PAD screen should appear.[1]
Related pages
[edit | edit source]- Atari 800
- Atari 400
- Atari 800 Troubleshooting Guide
- Atari 400 Troubleshooting Guide
- Atari 800 General Maintenance
- Atari 800 Power Supply Repair
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: testing with and without SALT II, including the RAM test, Table 3-2 "Defective RAM Boards" and Table 3-3 "Defective RAM Identifier" (section 3, pp. 3-1 to 3-15); disassembly and assembly of the 400 and 800, and PCB contact cleaning and lubricating (section 4, pp. 4-1 to 4-21); symptom checklist (section 6); parts lists for the RAM boards CA014801 and CA014802 (section 9). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.0 2.1 2.2 2.3 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: RAM board photograph with test points (p. 33) and parts list. Scan on the Internet Archive.
- ↑ Atari, Inc., Tech Tip 10, "Atari 400/800 System Lock-up", 22 February 1983, in section 10 of the ATARI Home Computer Field Service Manual 400/800.