Jump to content

Atari CX30 Potentiometer Cleaning and Replacement

From RetroTechCollection
Atari CX30 paddle potentiometer opened (Vintage Gaming and More)
A CX30 paddle potentiometer taken apart: the body with its black carbon track and inner metal ring (left), and the shaft carrying the wiper contacts (right), before cleaning

Each paddle of an Atari CX30 pair holds a 1 MΩ potentiometer, turned by the knob, and a spring-loaded push-to-make fire button.[1] The comp.sys.atari.8bit FAQ describes the potentiometer as linear.[2] It is wired as a variable resistor between the +5 V line and the paddle's own line to the console.[1] With age the contact between the wiper and the carbon track becomes intermittent,[3] and the paddle's object jitters on screen.[4] Vintage Gaming and More's repair is to open the potentiometer and clean it, and to replace it with a new 1 MΩ linear part when cleaning is not enough.[4][5] Switch and Potentiometer Repair covers the general method.

Symptoms

[edit | edit source]
  • The paddle's object shakes or jumps on screen while the knob is turned or held still.[4]
  • Atari's check with the Casino cartridge shows the numbers jumping by more than one step of 20 as the knob turns.[1]
  • The fire button does not respond: check the switch (Atari part CA011620-01) and its two wires as well as the potentiometer.[6][1]
  • Both paddles of a pair, or both fire buttons, fail together: the shared cable or the console is more likely. On the 2600, Atari's failure table for paddles points at the TIA (A201), capacitors C215 to C218 and the controller jacks J202 and J203.[7] Atari's tech tip 6 adds that early 2600 motherboards, revision 8 and lower, had an artwork error that could make the left paddles fail; it was corrected with a dot of insulation over a trace under the upper left corner of the cartridge socket J200, which should always be there.[8] See Atari 2600 Controller Port Repair.

Checking with a meter

[edit | edit source]
Atari CX30 paddle controller schematic (2600 field service manual figure 7-4)
Atari's figure 7-4: each potentiometer sits between +5 V (yellow, pin 7) and its paddle line; each button pulls its own line to ground (black, pin 8)

The two paddles share one dual four-conductor Y cable (Atari C010810) to a nine-pin plug.[1]

CX30 cable wiring (Atari FSM figure 7-4)
Signal Wire colour Plug pin
Paddle 1 button Green 3
Paddle 1 potentiometer Violet 9
Paddle 2 button Brown 4
Paddle 2 potentiometer Red 5
+5 V (both paddles) Yellow 7
Ground (both paddles) Black 8

[1]

  1. Unplug the paddles from the console.
  2. Set the meter to resistance and measure between pin 7 and pin 9 for paddle 1, or pin 7 and pin 5 for paddle 2.[1]
  3. Turn the knob slowly through its travel. The reading should change smoothly over a range up to about 1 MΩ, the value of the potentiometer, without dropping out or jumping.[6][3]
  4. Measure between pin 8 and pin 3 (paddle 1) or pin 4 (paddle 2) and press the fire button. The meter should show continuity only while the button is pressed.[1]

Tools and parts

[edit | edit source]
  • A Phillips screwdriver, a small flat screwdriver or similar tool for prying up small tabs, and needle-nose pliers.[4]
  • Rubbing alcohol and an old toothbrush or cotton buds.[4]
  • For a replacement: a 1 MΩ linear-taper potentiometer (Vintage Gaming and More used Radio Shack 271-211), a rotary tool with cutting and grinding bits, wire cutters and strippers, a soldering iron, a ruler and glue.[5]
Atari paddle parts (CX2600A parts list)
Part Atari part number
Resistor, variable, 1 MΩ (the potentiometer) C010464
Knob C010457
Nut C010416
Lockwasher C010417
Speed clip fastener 81-4004
Fire button C010739
Switch CA011620-01
Y cable C010810
Top cover C010737
Bottom cover C010738

[6]

Procedure

[edit | edit source]

Taking the paddle apart

[edit | edit source]
Atari CX30 paddle controller assembly (2600 field service manual figure 7-3)
Atari's figure 7-3: the knob, nut and washer on top, the potentiometer and fire button switch in the top cover, and the two screws in the bottom cover
Atari CX30 paddle with knob removed and fire button out (Vintage Gaming and More)
A paddle with its knob pulled off, showing the potentiometer shaft and nut, and the fire button switch lifted out
  1. Remove the two screws from the bottom of the paddle and lift off the bottom cover.[4][1]
  2. Pull the knob off the shaft. A small black metal tab holds the knob on the shaft; it sometimes stays inside the knob. Make sure you have it, because the knob needs it to stay on.[4]
  3. Unscrew the nut on the top of the cover and lift the potentiometer out.[4]
  4. Take the fire button out as well, and keep all the small parts together.[4]

Cleaning the potentiometer

[edit | edit source]
Atari CX30 paddle potentiometer, bending up the case tabs (Vintage Gaming and More)
Bending up one of the four metal tabs that hold the potentiometer together
  1. Find the four metal tabs on the top of the potentiometer and bend them up with the small screwdriver.[4]
  2. Separate the potentiometer into its parts: the plastic shaft with its metal contacts, and the body with the black carbon ring.[4]
  3. Dip the toothbrush or a cotton bud in rubbing alcohol and gently scrub the metal ring around the plastic shaft. Do not bend its contacts too much, and leave no cotton fibres on the six small metal prongs.[4]
  4. Clean the black ring on the body in the same way.[4]
  5. If the contacts look flattened, bend them up very slightly so that they press on the track.[4]
  6. Reassemble: put the plastic shaft through the ring so that the metal plates touch, refit the metal bottom with its opening lined up with the wires, then fit the threaded metal top.[4]
  7. Turn the shaft and check that it moves normally through its full range. If it does not, something is out of line; take it apart and fit it again.[4]
  8. Bend the four tabs back down with the needle-nose pliers.[4]
  9. Plug the paddles in and test them before closing the case. If the paddle still jitters, clean it again.[4]

Replacing the potentiometer

[edit | edit source]

Vintage Gaming and More's procedure for fitting a Radio Shack 1 MΩ linear-taper potentiometer in place of the original:[5]

  1. Take the paddle apart as above. Keep the original nut, which is used again as a washer.[5]
  2. Note which two tags of the old potentiometer carry the two wires, then cut or unsolder the wires at the tags.[5][3]
  3. Measure 5/8 in up the new potentiometer's shaft from the top of its threads, mark it and cut the shaft there with the rotary tool.[5]
  4. Take the small black metal piece out of the knob, then grind out the knob's half-round socket into a full circle so that it fits the round shaft of the new part.[5]
  5. Grind down the plastic ring on the top half of the paddle cover. The new part's threads are shorter than the original's and will not otherwise reach far enough for the nut; grind more if the nut will not start.[5]
  6. Remove the new potentiometer's nut and washer, clip off the small metal locating tab on its body, and discard its washer.[5]
  7. Fit the potentiometer into the case, put the original nut over the shaft on the top side as a washer, and screw the new nut on.[5]
  8. Strip the wires and solder them to the tags of the new potentiometer that match the old ones. See Through-Hole Soldering for the soldering itself.[5][3]
  9. Put glue in the hole in the knob and push it onto the shaft, or wrap electrical tape round the shaft so that the knob is a tight fit. Let the glue dry before turning the knob.[5]
  10. Refit the fire button and the wires, and screw the bottom cover back on.[5]

Vintage Gaming and More notes that a 500 kΩ potentiometer also works and makes the paddle more responsive, because games use only part of the potentiometer's rotation; the knob then has to be turned further for the same movement.[5]

Testing

[edit | edit source]
  1. Repeat the meter checks above: a smooth change of resistance between pins 7 and 9 (or 7 and 5), and continuity on the button lines only while the button is pressed.[1]
  2. On a 2600, plug the paddles into the left controller port with the Casino cartridge and press GAME RESET. Press the button on one paddle: a pair of numbers should appear. Turn the knob: one set of numbers should run from 20 to 200 in steps of 20 and never advance by more than one step. Repeat for the other paddle.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 7, "Game Controllers": paddle controller description (1 megohm potentiometer, spring-loaded push-to-make button) and figure 7-3 assembly (p. 7-4, PDF p. 130); figure 7-4 paddle controller schematic with wire colours and plug pins, and the paddle controller check with the Casino cartridge (p. 7-5, PDF p. 131). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
  2. ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, section 6.3, CX30 Paddle Controller: "a linear 1 Megaohm potentiometer" in each controller. mcurrent.name. Community reference.
  3. ↑ 3.0 3.1 3.2 3.3 Switch and Potentiometer Repair, sections "Test the part" and "Replace a potentiometer".
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 Vintage Gaming and More, "Atari Paddle Repair (Cleaning Jittery Paddles)", 21 July 2010, updated 5 June 2015, retrieved 25 October 2026: tools, taking the paddle apart, opening the potentiometer by its four tabs, cleaning and reassembly, testing before closing.
  5. ↑ 5.00 5.01 5.02 5.03 5.04 5.05 5.06 5.07 5.08 5.09 5.10 5.11 5.12 5.13 Vintage Gaming and More, "Atari Paddle Repair (Pot Replacement)", 28 June 2010, updated 5 June 2015, retrieved 25 October 2026: fitting a Radio Shack 271-211 1 MΩ linear-taper potentiometer, cutting its shaft, grinding the knob and cover, and the note on 500 kΩ parts.
  6. ↑ 6.0 6.1 6.2 Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 8, CX2600A parts list, paddle entries (p. 8-7, PDF p. 143, and PDF p. 144). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
  7. ↑ Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 3, symptom checklist, "Paddle controllers": A201, C215-C218, J202-J203 (PDF p. 94). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
  8. ↑ Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, tech tip 6, "Left Paddle Failure" (PDF p. 147). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.