Atari CX40 Cable Replacement

The Atari CX40 joystick's cable has six wires. One end is moulded into a nine-way plug; at the other end each wire carries a slide-on metal contact that pushes onto a finger on the joystick's circuit board.[1][2] Best Electronics, which has made replacement cables, lists the weaknesses of the original: the flexible nose of early plugs let the female contacts splay open; the thin cable was moulded straight into a stiff plug body with no flexible strain relief, so the wires broke where they flexed against it; the wires were thin (28 AWG on the cable it photographed); and the crimped contacts could pull off the wire ends or snap.[3] The repair is to refit a single contact, or to replace the whole cable.
Faults in the switches and the inner handle are covered in Atari CX40 Circuit Board and Handle Replacement.
Symptoms
[edit | edit source]- Every direction and the fire button fail, or work only with the cable held in one position. Look for cuts in the outer jacket, exposed copper and sharp bends, especially where the cable enters the moulded plug.[2][3]
- One line fails while its switch tests good at the board: a broken wire or a contact that has come off its wire.[3]
- The joystick works only when the plug is pushed sideways in the port. Look into the plug for damaged female contacts, or male pins from a port broken off inside them. One to three empty contact holes in the plug are normal.[2][3]
- The console's own port can have pushed or broken pins; Atari's tech tip 9 for the 2600 says to check J202 and J203 and replace any that show problems.[4] See Atari 2600 Controller Port Repair.
Tools and parts
[edit | edit source]- A Phillips screwdriver, a small torch and a continuity meter.[2]
- Needle-nose pliers or a crimp tool and a soldering iron, if you are refitting contacts or fitting a cable with bare ends. See Connector Pin Replacement and Crimping.[2]
- A replacement cable. Atari's service part is C010726.[5] Best Electronics gives the original six-conductor joystick cable as CA014058, now sold out, and sells its own seven-foot replacement, which has thicker 26 AWG wires, a flexible strain relief at the plug and gold-plated contacts already fitted.[2][3]

Best Electronics also lists two other replacement cables, and each needs extra work:[2]
- A non-Atari cable made by PPI, 5½ ft long with the Atari colour code. Its loose wires are only 2¼ to 2⅝ in long and only the black one has a slide-on contact; the other five must be stripped and soldered to the board's contact pads. On the earlier two-edged board, three of them need extension wires to reach the pads on the far side.
- A thicker four-foot Atari cable from another product, with all nine conductors fitted with contacts and a different colour code. Best Electronics cuts off the three conductors the joystick does not use, because connecting one of them by mistake can glitch or reset the console and may damage it. Its larger moulded strain relief needs the hole in the joystick base opened slightly with a rat-tail file.
Best Electronics sells loose contacts that fit the board fingers, for refitting a contact that has come off its wire.[2]
Procedure
[edit | edit source]Testing the cable
[edit | edit source]
| Plug pin | Wire colour | Line |
|---|---|---|
| 1 | White | Up |
| 2 | Blue | Down |
| 3 | Green | Left |
| 4 | Brown | Right |
| 6 | Orange | Fire |
| 8 | Black | Common |
On the computer's or console's port, pins 1 to 5 are in the wider row and pins 6 to 9 in the narrower one.[6] The joystick's plug is the mating half, so as you look into the plug its numbering is the mirror image of the port's.
- Unplug the joystick. Put the meter on pins 8 and 1 and hold the stick forward; the meter should show continuity.[1]
- Keep the stick held and flex the cable gently, first where it enters the plug and then where it enters the joystick. A reading that drops out locates a broken wire.[3][7]
- Repeat for pins 2, 3, 4 and 6 with their switches pressed.[1]
- If a line still fails, open the joystick: remove the four screws from the base and lift it off with the boot pointing down, catching the fire button spring.[2]
- Look at each wire's slide-on contact on the board. A contact that has pulled off its wire, snapped, or been squashed flat explains a dead line.[3]
- Check each plug pin to the end of its wire at the board, using the table above. Each should read continuity, and no pin should connect to any other.[1][7]
Refitting a single contact
[edit | edit source]- Strip the end of the wire.[2]
- Crimp the new contact onto the bare copper with needle-nose pliers, then solder the wire to the contact as a backup.[2]
- Push it onto its finger on the board. Best Electronics' substitute contacts need two to three times the usual force the first time; once fitted they slide on and off normally.[2]
See Connector Pin Replacement and Crimping for the general method.
Removing the old cable
[edit | edit source]- With the joystick open, pull each slide-on contact off the board by gripping the metal contact itself, not the wire.[2]
- Lift the cable's moulded strain relief out of the cutout in the corner of the base, which is shaped to grip it.[8]
Fitting the new cable
[edit | edit source]- Seat the new cable's strain relief in the cutout. A thicker moulding may need the hole opened slightly with a rat-tail file.[2]
- For a cable with contacts fitted, push each contact onto the board in the colour order for your board (shown in the wiring table in the board replacement guide). On the later single-edge board the order is brown, white, black, blue, green and orange from the top right corner downwards, with the switch contacts facing you.[2]
- Check each contact's orientation: a contact turned 180 degrees slides on but does not touch the board's contact surface.[2]
- For a cable with bare wires, strip and solder each wire to its pad, adding extension wires on a two-edged board where the wires are too short.[2]
- If the cable has more than six conductors, cut the unused ones back so that none can touch the board.[2]
- Twist the six wires into one tight bundle, refit the fire button spring and the base, and check that the halves close fully.[2][3]
- Look down each screw hole with a torch for a trapped wire, then fit the four screws.[2]
Testing
[edit | edit source]- With the meter, check each of pins 1, 2, 3, 4 and 6 to pin 8 while operating its switch, flexing the cable at both ends as you do.[1][7]
- On a 2600, run Atari's joystick check: the Combat cartridge, game 13, joystick in the left player port. The plane should go down, go up, speed up, slow down and fire as the stick is pushed away, pulled back, moved right and left, and the button pressed.[1]
Related pages
[edit | edit source]- Atari CX40
- Atari CX40 Circuit Board and Handle Replacement
- Atari 2600 Controller Port Repair
- Atari 2600 and 2600A Field Service Manual
- Connector Pin Replacement and Crimping
- Continuity Testing and Signal Tracing
References
[edit | edit source]- ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 7, "Game Controllers": figure 7-1 joystick construction with the wire colours at the board (p. 7-1, PDF p. 127); figure 7-2 joystick schematic, wire colours and plug pins (p. 7-2, PDF p. 128); joystick check with the Combat cartridge (p. 7-3, PDF p. 129). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 Best Electronics, "Atari CX40 Joystick parts": things to check first (plug contacts, cable damage), rebuild instructions, wire colour codes, the original cable CA014058, the PPI replacement cable and its bare wires, substitute crimp contacts, and the thicker nine-conductor Atari cable with its unused conductors removed and the strain relief hole opened with a rat-tail file. Retrieved 25 October 2026. Parts supplier; community source.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Best Electronics, "The story behind the making of the Best CX40 cable": faults of the original CX10 and CX40 cables (flexible plug nose, no strain relief at the plug, thin wires, contacts pulling off), the photographed 26 AWG and 28 AWG contacts, wires trapped between the case halves and twisting them into a bundle. Retrieved 25 October 2026. Parts supplier; community source.
- ↑ Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, tech tip 9: check the 9-pin connectors J202 and J203 for pushed or broken pins (PDF p. 147). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 8, X-Y controller entries in the CX2600 parts list (p. 8-4, PDF p. 140) and the CX2600A parts list (PDF p. 144): cable C010726. Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, section 1.15, controller port pin layout (pins 1 to 5 upper row, 6 to 9 lower row). mcurrent.name. Community reference.
- ↑ 7.0 7.1 7.2 Continuity Testing and Signal Tracing, sections "Buzz out a cable or connector" and "Find an intermittent open".
- ↑ Wikipedia, "Atari CX40 joystick", section "Description": the cutout in the base that grips the cable's moulded strain relief.