Atari CX40 Circuit Board and Handle Replacement

The Atari CX40 joystick has two parts that wear out with use: the five dome switches on its small circuit board, and the white inner handle whose bottom ring presses on them.[1][2] When a direction or the fire button stops working, or works only under heavy pressure, the usual repair is to fit a new circuit board and a new inner handle together. Best Electronics, which sells the parts, reports that this cures most failing CX40s and that the rest need a new cable, boot, boot ring or fire button spring.[2] The procedure applies to the CX40 with deep screw holes in its base. The earliest joysticks (the CX10 type) use springs and a different board; Atari's field service manual says these cannot be repaired, and Best Electronics reports that only the cable is common to both.[3][1][2]
A fault in the cable is covered in Atari CX40 Cable Replacement.
Symptoms
[edit | edit source]- One direction, or the fire button, is dead or intermittent, and pressing harder brings it back.[4] The dome contacts wear out; Best Electronics finds that it is usually the copper contact on the board under the dome that has worn, not the dome itself.[2] A dome can also turn inside out once the clear tape over it lets go.[4]
- A click from under the rubber boot as the stick moves, and one or more directions lost. This is a cracked outer ring on the inner handle.[4] The ring transmits the force from the stick to the switches, so a break in the ring, or in one of the tabs joining it to the stick, stops that direction working.[1]
- Loose plastic rattling inside the case. If the cone-shaped post in the centre of the base has broken off, Best Electronics considers the joystick not worth rebuilding.[2]
- The fire button needs a hard press. Heavy thumb pressure can flatten ("mushroom") the small post in the centre of the button until it is too short to press its dome.[2]
- All five lines fail together, or the joystick works only with the cable held in one position: suspect the cable and see Atari CX40 Cable Replacement.[5]
- A known good joystick also fails on the same console: the fault is in the console. Atari's 2600 symptom checklist names the controller jacks J202 and J203 and the 6532 (A202) for a joystick that does not work.[6] See Atari 2600 Controller Port Repair, or Atari 800XL Controller Port Repair on an 800XL.
Checking the switches with a meter
[edit | edit source]
Each of the five switches connects its own line to the black common wire on pin 8; the joystick has no other electronics.[3] With the joystick unplugged, a continuity meter shows each switch directly from the plug. See Continuity Testing and Signal Tracing for the general method.
| Switch | Wire colour | Plug pin | Meter between |
|---|---|---|---|
| Up (stick pushed forward) | White | 1 | Pins 1 and 8 |
| Down | Blue | 2 | Pins 2 and 8 |
| Left | Green | 3 | Pins 3 and 8 |
| Right | Brown | 4 | Pins 4 and 8 |
| Fire | Orange | 6 | Pins 6 and 8 |
| Common | Black | 8 | – |
- Unplug the joystick from the console.[3]
- Put the meter probes on pin 8 and pin 1. Push the stick forward: the meter should show continuity, and open circuit again when the stick is released.[3]
- Repeat for pins 2, 3 and 4 with the stick pulled back, pushed left and pushed right, and for pin 6 with the fire button pressed.[3]
- Push the stick to each diagonal. Two lines close together, which is how the console sees eight directions.[3]
On the port, pins 1 to 5 are in the wider row and pins 6 to 9 in the narrower one.[7] The joystick's plug is the mating half, so as you look into the plug its numbering is the mirror image of the port's.
A switch that reads open, or closes only under heavy pressure, is a worn dome or board.[2][4] A lost direction that comes with a click from under the boot points to the handle's ring.[4]
Tools and parts
[edit | edit source]- A Phillips screwdriver and a small torch.[2]
- A multimeter with a continuity range.
- A new circuit board and a new inner handle. Best Electronics advises replacing them as a matched pair. It reports that a worn board leads users to press harder, which overstresses the handle's ring.[2][4]
- A fire button spring, which is easily lost, and a fire button if its centre post is flattened.[2]
| Part | Atari part number |
|---|---|
| PC board, two-edged connection (earlier) | CA015396 |
| PC board, single-edge connection (later) | CA016741 |
| Handle | C012116 |
| Fire button | C012114 |
| Spring | C012951 |
| Boot | C012109 |
| Retainer ring | C012110 |
| Top cover | C012107-02 |
| Bottom case | C012108-02 |
Atari also sold the CX41 Joystick Repair Kit, CA020476, with a circuit board, three springs, an insert, a boot, a retaining ring and repair instructions C020484.[9] Best Electronics sells new-made replacement boards and inner handles, and reports that the two Atari board styles are interchangeable.[2] A community-designed replacement board, "Atari CX40 rev 2019.1" by mozzwald, is shared on OSH Park; it uses low-profile Alps SKRRAAE010 tactile switches, which its designer describes as soft, with no click on the directions.[10]
Replacing only the metal domes on an old board is possible, but Best Electronics found that boards repaired that way lasted about a tenth as long as new boards: the old adhesive tape no longer held the new domes and they moved about under it.[2]
Procedure
[edit | edit source]Opening the joystick
[edit | edit source]
- Turn the joystick upside down and remove the four Phillips screws from the base. Keep them together.[2]
- Hold the two halves together with the boot pointing down, and lift the base off the top case slowly, only a little at first.[2]
- Before lifting further, note how the circuit board sits: its five silver contacts face down, it sits on two locating studs in the top case, and one of its contacts is under the fire button.[2]
- Lift the base away. Take the small spring off the fire button's centre post, below the board, and put it somewhere safe; it falls out easily.[2]
- Check the cone-shaped post in the centre of the base. If it has broken off, stop: Best Electronics considers the joystick not rebuildable.[2]
Inspecting the parts
[edit | edit source]- Look at the white inner handle's bottom ring and the four studs on it for cracks and white stress marks.[4]
- Look at the domes on the board. A dome that has turned inside out, or tape lifting from around the domes, means the board needs replacing.[4]
- Look at the fire button's centre post. If its end has spread and shortened, the button will not press a new dome properly; fit a new button.[2]
Replacing the circuit board
[edit | edit source]
- Identify the board. The earlier board has wire contacts on two edges; the later board has all six on one edge.[3][2]
- Pull each wire's slide-on contact off the board by gripping the metal contact itself. Do not pull on the wire, which comes out of its contact easily.[2]
- Fit the new board in the same position, contacts facing down and seated on the two locating studs, with the right contact under the fire button.[2]
- Push each wire contact onto its finger on the board. Look at how the contact's spring side meets the board: a contact turned 180 degrees still slides on but does not touch the board's contact surface.[2]
- Wire it in the order shown in the table below for the board you are fitting.[2][3]
| Board | Wire order |
|---|---|
| Two-edged (earlier) | Orange, white and green on one edge; brown, blue and black on the other |
| Single-edge (later) | Brown, white, black, blue, green, orange, from the top right corner of the board downwards, with the switch contacts facing you |
Replacing the inner handle
[edit | edit source]- Before taking the old handle out of the boot and top case, note where the square locating tab on its bottom ring sits. It fits between two small studs at the 12 o'clock position, with the fire button at 1 o'clock.[2]
- Lift out the old handle and fit the new one in the same position. It fits only one way.[2]
Closing the joystick
[edit | edit source]- Put the fire button spring back on the button's centre post.[2]
- Holding the board in place, twist the six loose wires into one tight bundle. A trapped bundle stops the case closing and shows that something is wrong; a single loose wire can be trapped between the two halves and cut by the screws.[2][5]
- Fit the base and check that the two halves close fully.[5]
- Turn the joystick over and look down each of the four screw holes with a torch for any wire showing at the bottom.[2]
- Fit the four screws.[2]
Testing
[edit | edit source]- Repeat the meter checks above. Each of pins 1, 2, 3, 4 and 6 should show continuity to pin 8 only while its switch is pressed.[3]
- On a 2600, plug the joystick into the left player port with the Combat cartridge, select game 13 and press GAME RESET. Pushing the stick away from you makes the plane go down and pulling it makes it go up; right speeds it up and left slows it down; the red button fires.[3]
- Best Electronics suggests Missile Command on the 2600 to check all eight directions and the fire button after a rebuild.[2]
Revision notes
[edit | edit source]- Atari used two boards, the two-edged CA015396 and the single-edge CA016741.[8] Best Electronics reports that they are interchangeable.[2]
- Best Electronics groups Atari's inner handles into three styles: an early handle (1979 to 1980) with a thin outer ring that cracked easily, a second with a thicker ring, and a final version with four flexible arms carrying the studs.[4]
- The CX10 joystick uses a separate actuator plate and springs under its handle, and its board is not interchangeable with the CX40's.[4] On the underside, the CX10-type joystick's screw heads sit about 3/16 in below the surface, the CX40's about 5/8 in.[2]
Related pages
[edit | edit source]- Atari CX40
- Atari CX40 Cable Replacement
- Atari 2600 Controller Port Repair
- Atari 800XL Controller Port Repair
- Atari 2600 and 2600A Field Service Manual
- Continuity Testing and Signal Tracing
- Connector Pin Replacement and Crimping
References
[edit | edit source]- ↑ 1.0 1.1 1.2 Wikipedia, "Atari CX40 joystick", sections "Description" and "Problems": construction, the control ring and its tabs, worn switches.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.26 2.27 2.28 2.29 2.30 2.31 2.32 Best Electronics, "Atari CX40 Joystick parts": rebuild kit, early and later versions, things to check first, rebuild instructions, wire colour codes for both boards, the experience with replacement dome contacts, and parts list. Retrieved 25 October 2026. Parts supplier; community source.
- ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 7, "Game Controllers": joystick (X-Y) controller description, the note that the earliest spring-button joysticks cannot be repaired, and figure 7-1 (p. 7-1, PDF p. 127); figure 7-2 joystick schematic with wire colours and plug pins (p. 7-2, PDF p. 128); joystick check with the Combat cartridge (p. 7-3, PDF p. 129). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 Best Electronics, "The story behind the Best CX40 Super Handle": the three styles of Atari inner handle, the cracked outer ring and the click it makes, inverted dome contacts, and the CX10 actuator plate and board. Retrieved 25 October 2026. Parts supplier; community source.
- ↑ 5.0 5.1 5.2 Best Electronics, "The story behind the making of the Best CX40 cable": wire breakage at the plug, wires trapped between the case halves and Atari's practice of twisting them into a bundle. Retrieved 25 October 2026. Parts supplier; community source.
- ↑ Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 3, symptom checklist, "Joystick does not work": A202, J202, J203 (PDF p. 94). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, section 1.15, controller port pin layout (pins 1 to 5 upper row, 6 to 9 lower row). mcurrent.name. Community reference.
- ↑ 8.0 8.1 Atari, Inc., 2600/2600A Domestic (M/N) VCS Field Service Manual, section 8, X-Y controller entries in the CX2600 parts list (p. 8-4, PDF p. 140) and the CX2600A parts list (PDF p. 144). Hosted as File:Atari 2600 and 2600A Field Service Manual.pdf.
- ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, section 6.3: CX41 Joystick Repair Kit, CA020476, and its contents. mcurrent.name. Community reference.
- ↑ mozzwald, "Atari CX40 rev 2019.1", OSH Park shared project, shared 26 March 2019: replacement CX40 board using Alps SKRRAAE010 tactile switches.