Atari 1020 Pen Solenoid Circuit Repair

The Atari 1020 Color Printer lifts and lowers its ballpoint pen with an electromagnet (solenoid) on the printer mechanism. The controller A2 starts each movement with a single pulse of about 5.4 ms from its C0 output (pin 9, pen up) or C1 output (pin 10, pen down), and the pen then stays where it is until the next pulse.[1] When a 1020 that moves its carriage and paper normally never draws, or draws all the time, the fault lies in the pen mechanism, the solenoid, the transistor driver between A2 and the solenoid, its +5 V supply, or A2 itself. Atari's pen-down and pen-up flowcharts trace that path one stage at a time.[1]
How the circuit works
[edit | edit source]The solenoid's two leads come to connector J4, pins 12 and 13. Four transistors form a bridge that drives current through it one way or the other from Vp, the +5 V supply made by regulator A5:[1]
- Pen up: Vp, Q6, J4 pin 13, the solenoid, J4 pin 12, Q5, ground.
- Pen down: Vp, Q7, J4 pin 12, the solenoid, J4 pin 13, Q4, ground.
Q1 and Q2 take A2's pulses to the bridge, and Q3 holds Q7 off if C0 and C1 are ever both active at once. The diodes D5, D6, D8 and D9 with the zener diode D7 form a bridge that limits the voltage spike when the solenoid switches; Atari's description puts the limit at about 16 V, while the parts list gives D7 as an HZ11 zener marked 9.9 V.[1] Vp reaches the mechanism on J4 pin 7.[1]
Symptoms
[edit | edit source]- Pens do not write, though the carriage moves and the paper feeds: start at the pen-down checks.
- Pens write all the time: start at the pen-up checks.[1]
Atari's power-up flowchart sends these two faults to the pen-down and pen-up charts respectively.[1] A faded square in the four-square pattern drawn at switch-on means that pen is running dry; pens are covered in the Atari 1020 Maintenance Guide.[2] If nothing moves at all, see the Atari 1020 Troubleshooting guide; if the carriage or paper grinds, see Atari 1020 Motor Pinion Gear Replacement.
Safety
[edit | edit source]Unplug the AC adaptor before opening the printer or changing any part.[1] Keep magnetic objects away from the electromagnet assembly.[1]
Tools and parts
[edit | edit source]- A multimeter and an oscilloscope or logic probe that can catch a single pulse of about 5 ms.[1]
- An Atari computer with BASIC to run the test program below.[1]
- A soldering iron and desoldering tools; the electromagnet's wires are soldered to the board.[1]
| Location | Part | Atari part number |
|---|---|---|
| A2 | 6805V controller, ROM version | FC100347 |
| A5, A6 | HA17805P +5 V regulator | FC100350 |
| Q1, Q2, Q3 | 2SA844(C) or (D) PNP transistor | FC100351 |
| Q4, Q5 | 2SD788(C) or (D) NPN transistor | FC100352 |
| Q6, Q7 | 2SB739(C) or (D) PNP transistor | FC100353 |
| D5, D6, D8, D9 | 1S2076FA signal diode | FC100356 |
| D7 | HZ11 zener diode (VZ 9.9 V) | FC100358 |
| X1, X2 | PX-1 4 MHz crystal | FC100357 |
| – | Electromagnet assembly (solenoid) | FC100375 |
| – | Ejection lever spring | FC100380 |
Procedure
[edit | edit source]Opening the printer
[edit | edit source]Open the case as described in Atari 1020 Motor Pinion Gear Replacement#Opening the printer; the board stays in the lower case and the mechanism connects to it by a ribbon cable to J4.[1][3] The printer mechanism does not have to be connected to see the drive pulses on the board.[1]

Test program
[edit | edit source]Atari's pen test uses its text-mode test program, run from BASIC with the 80-column and international character set codes, which gives rapid pen up and down movement.[1]
10 OPEN #1,8,0,"P" 20 DIM A$(8) 30 ? #1:? #1 40 INPUT A$ 50 IF A$="SKIP" THEN GOTO 30 60 ? #1;A$ 70 FOR X=0 TO 126 80 IF X=27 THEN 100 90 ? #1;CHR$(X); 100 NEXT X 110 ? #1;CHR$(127) 120 GOTO 40
At the question mark, type the code for 80 columns (ESC, ESC, CONTROL-S) followed by the code to enable the international character set (ESC, ESC, CONTROL-W), with no spaces between them, and press RETURN. Press RETURN again to repeat the test.[1]
Check the mechanism first
[edit | edit source]- With the power off, pull the actuator of the electromagnet free of its permanent magnet by hand. The pen up and down mechanism should move freely and smoothly without binding.[1]
- If it does not, check the electromagnet assembly; the gap of 0.1 to 0.2 mm between actuator and coupling lever with the actuator attracted and a pen on paper; that the ejection lever shaft works freely with enough tension from the ejection lever spring; that nothing else impedes the mechanism; and that the actuator spring overcomes the ejection lever spring. Adjust or replace as needed.[1]
Pens do not write (pen-down checks)
[edit | edit source]- Run the test program. Check for a single pulse of about 5.4 ms at J4 pin 12 each time the pen should go down. If it is there, the solenoid is not responding: replace the electromagnet assembly (below).[1]
- If there is no pulse, measure the output of A5. It should be 5 V DC; if not, replace A5. See Testing Diodes, Transistors and Regulators.[1]
- Measure J4 pin 7. It should also be 5 V; if A5 is good and pin 7 is not, find and repair the open circuit between them. See Continuity Testing and Signal Tracing.[1]
- Check for a logic-low pulse at A2 pin 10 while the test runs. If there is none, check that the crystals X1 and X2 are running, then replace A2, and if the pen still does not go down, replace A1.[1]
- If A2 pin 10 pulses, check Q1, Q4 and Q7 against the table below. Replace any transistor that does not switch; if all three are good, Atari replaced the board.[1]
The flowchart asks for X1 and X2 at 4.43 MHz, but the parts list and the description of A2 give 4 MHz crystals.[1]
Pens write all the time (pen-up checks)
[edit | edit source]- Run the test program and check for a single pulse of about 5.4 ms at J4 pin 13 each time the pen should lift. If it is there, replace the electromagnet assembly.[1]
- If there is no pulse, check for 5 V at the output of A5 and at J4 pin 7. If either is missing, Atari's chart sends you to its supply chart (chart I, p. 4-11).[1]
- Check for a logic-low pulse at A2 pin 9. If there is none, swap A2, then A1.[1]
- If A2 pin 9 pulses, check Q2, Q5 and Q6 against the table below. Replace a transistor that does not switch; if all three are good, Atari replaced the board.[1]
| Pen up (A2 pin 9) | Pen down (A2 pin 10) | Emitter | Base | Collector |
|---|---|---|---|---|
| Q2 | Q1 | Connected to Vc | 5 V to 4 V | 0 V to 5 V |
| Q5 | Q4 | Connected to ground | 0 V to 1 V | 5 V to 0 V |
| Q6 | Q7 | Connected to Vp | 5 V to 4 V | 5 V to 0 V |
Each change is a pulse of about 5 ms while the pen test runs. Atari's figure gives the lead order of these transistors as base, collector, emitter.[1] Replacing a transistor is covered in Through-Hole Desoldering and Through-Hole Soldering.
Replacing the electromagnet assembly
[edit | edit source]
- Remove the Phillips screw that holds the electromagnet assembly to the printer module frame, at the right front under the assembly.[1]
- Desolder the two electromagnet wires from the board, noting which goes where.[1]
- Fit the holding pin of the new assembly into the frame unit and fit its screw without tightening it.[1]
- With a pen in the rotary pen holder, pull the actuator out to the pen-down position and set the gap between the actuator and the coupling lever to 0.1 to 0.2 mm. Tighten the screw.[1]
- Pull the actuator to the pen-up position and set the gap between the pen tip and the platen to 0.6 to 0.7 mm with the stopper screw. Turning it anticlockwise widens the gap.[1]
- Solder the black and red wires back to their original points on the board.[1]
The ejection lever spring is replaced with the electromagnet assembly removed: move the slider unit to the centre of the carriage, note how one leg of the spring sits over the frame and the other over the ejection lever shaft, remove the 1.5 mm E-ring from the end of the shaft, slide the shaft to the right, change the spring, refit the shaft through the left frame and the E-ring, then refit the electromagnet and make both adjustments again.[1]
Testing
[edit | edit source]- Switch on with paper and pens loaded. The print head moves to the far left, waits two or three seconds and draws four coloured squares.[1]
- Run the pen test program. The printer should draw the full character set.[1]
Related pages
[edit | edit source]- Atari 1020
- Atari 1020 Troubleshooting
- Atari 1020 Maintenance Guide
- Atari 1020 Motor Pinion Gear Replacement
- Atari 1020 Documentation
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 Atari, Inc., 1020 Color Printer Field Service Manual, FD100288 Rev. 01, August 1983: A2 controller and pen up-down solenoid drive circuit, p. 1-10, and figures 1-7 and 1-8, p. 1-11 (PDF pp. 20-21); silkscreen, figure 2-1, p. 2-3, and schematic, figure 2-2, p. 2-5 (PDF pp. 25 and 27); internal test p. 3-6, text test program and pen up-down test p. 3-7, character command codes, table 3-1, p. 3-9 (PDF pp. 34, 35 and 37); pen-down and pen-up flowcharts and table 4-1 with transistor lead order, pp. 4-5 to 4-7 (PDF pp. 43-45); disassembly warning p. 6-4; electromagnet removal and actuator adjustment p. 6-5, figures 6-3 and 6-4 and the pen and platen adjustment p. 6-6, ejection lever spring p. 6-10 (PDF pp. 56-58 and 62); parts list p. 7-1 (PDF p. 67). Hosted here as File:Atari 1020 Color Printer Field Service Manual FD100288 Rev 01.pdf.
- ↑ Atari, Inc., The Atari 1020 Color Printer Owner's Guide (1982), test pattern and pen pages. Hosted here as File:Atari 1020 Color Printer Owner's Guide.pdf.
- ↑ RetroNerd, "Atari 1020 Colour Printer Plotter Repair", 7 January 2024. The board in the lower case and the ribbon cable to the mechanism. Community repair write-up.