Atari 800 SIO Port Repair

Cassette recorders, disk drives, printers and interfaces connect to the Atari 800 through the 13-pin peripheral socket J204 on the right-hand side. The socket is mounted on the power supply board, beside the monitor socket J205; its signals reach the motherboard through the 22-pin board-to-board connector J201, which mates with J115 on the motherboard.[1] On the motherboard POKEY (A101) sends and receives the serial data and clocks, the PIA (A102) handles the command, proceed and interrupt lines, and the PIA switches the cassette motor through the transistor Q107.[1][2] When the 800 cannot load from or save to any peripheral, or the recorder's motor never starts, Sams' service data gives the checks for each line.[2]
Symptoms
[edit | edit source]- A known-good recorder or drive will not load, or will not save, on this computer.[2]
- The cassette motor does not start when loading or saving.[2]
- A cassette's voice track is not heard: see Atari 800 Sound Repair.[1]
- Bent or broken pins in the socket: Atari's visual inspection checks the peripheral jacks for them.[1]
Check the cable and the peripheral on another computer first. Sams' preliminary check for an 800 that will not load or save a cassette program is to substitute POKEY.[2]
Safety
[edit | edit source]Pin 10 of the socket carries +5 V and pin 12 carries +12 V; pins 4 and 6 are ground.[1] Do not short pin 10 or 12 to ground or to a signal pin while probing. Unplug the adaptor before removing the power supply board.
Tools and parts
[edit | edit source]- A logic probe, an oscilloscope and a meter.[2]
- An Atari program recorder and a blank tape, or a disk drive, for testing.[2]
- Optional: SALT II and Atari's peripheral port test connector; Best Electronics sells SALT 2.05 (TE15644) and the SIO shorting plug for the port test (TE15639).[1][3]
- Parts as found: POKEY (C012294), the PIA (C014795, or C014812 as an alternative), the MPS-A55 transistor for Q107 (C014809) and the 13-pin right-angle socket J204 (C012995).[1]
The socket
[edit | edit source]
| J204 pin | Signal | J201/J115 pin | Motherboard end |
|---|---|---|---|
| 1 | Clock in | 8 | POKEY BCLK (pin 26) |
| 2 | Clock out | 7 | POKEY OCLK (pin 27) |
| 3 | Data in | 9 | POKEY SID (pin 24) |
| 4, 6 | Ground | – | – |
| 5 | Data out | 10 | POKEY SOD (pin 28) |
| 7 | Command | 11 | PIA CB2 (pin 19) |
| 8 | Motor control | 4 | Q107, driven from PIA CA2 (pin 39) through R159 |
| 9 | Proceed | 12 | PIA CA1 (pin 40) |
| 10 | +5 V / ready | – | +5 V B on the power supply board |
| 11 | Audio in | 13 | Through C211 (10 µF) on the power supply board to the audio circuit |
| 12 | +12 V | – | +12 V on the power supply board |
| 13 | Interrupt | 14 | PIA CB1 (pin 18) |

On the motherboard the serial lines pass through the 100 Ω resistors R168 to R174, with 4.7 kΩ pull-ups (R129) and .001 µF capacitors C182 to C188 to ground, before they reach J115.[1]
Procedure
[edit | edit source]Open the machine
[edit | edit source]- Turn the unit upside down, remove the five bottom cover screws and tilt the back of the bottom cover up and towards you to remove it.[1]
- Remove the two screws from the aluminium casting flange and the single screw from the lower left corner of the power supply board. Disconnect the speaker cable and set the speaker aside.[1]
- Turn the unit over, pull the back of the top cover up to 90°, unplug the keyboard ribbon cable and set the top cover aside.[1]
- Unplug the RF cable and the power supply harness, remove the three screws from the power supply board and lift it straight up. J204 and J201 are now accessible; Atari 800 Power Supply Repair has the figure.[1]
- For the motherboard side, turn the unit upside down, remove the nine screws from the lower shield and lift the motherboard and shield out of the casting. POKEY and the PIA are in 40-pin sockets.[1]
Cannot save
[edit | edit source]Sams' check, using a program recorder:[2]
- Type in or load a short program. Type CSAVE and press RETURN; after two beeps, press PLAY and RECORD on the recorder and press RETURN again.
- While it saves, check the waveforms on pins 26, 27 and 28 of POKEY (A101).
- If any of them is missing, check A101 by substitution.
- If the waveforms are correct, check the connections at pins 8, 7 and 10 of J201 and pins 1, 2 and 5 of J204.
Cannot load
[edit | edit source]- Type CLOAD and press RETURN; after one beep, press PLAY on the recorder and press RETURN again.[2]
- Check for pulses at pin 24 of POKEY while it loads.[2]
- Sams then directs the check to the connections at pin 9 of J201 and pin 3 of J204.[2] If there are no pulses at pin 24 while the recorder plays, follow the line back from pin 24 through its 100 Ω resistor and J115 pin 9 to J204 pin 3; if there are pulses but nothing loads, substitute POKEY, as Sams' preliminary check advises.[1][2]
Recorder motor does not start
[edit | edit source]- Type
POKE 54018,52and press RETURN. Put the logic probe on pin 39 of the PIA (A102): it should go from high to low, which starts the recorder motor.[2] - If it stays high, check A102 by substitution.[2]
- If it changes correctly, check the switch transistor Q107 and the connections at pin 4 of J201 and pin 8 of J204.[2] On the schematic Q107's emitter is on +5 V A, its base is driven from CA2 through R159 (2.7 kΩ), and its collector reaches J115 pin 4 through the bead L106.[1]
- Type
POKE 54018,60and press RETURN to stop the motor.[2]
SALT II port test
[edit | edit source]Atari's 800 port test (P and RETURN) needs the hand controller jack test connector and the peripheral port test connector fitted. Reseat them and test again before replacing anything, then decode any failure with Atari's port test legend (table 7-3), which names the PIA control pins 18, 19, 39 and 40 and POKEY's clock pins 26 and 27 for the peripheral lines.[1]
Repair the socket
[edit | edit source]- With the power supply board out, inspect J204 for bent or broken pins and its solder joints for cracks.[1]
- Check continuity from each J204 pin to its J201 pin (table above), and on the motherboard from each J115 pin through its resistor to the chip pin. See Continuity Testing and Signal Tracing and, for a damaged socket, Through-Hole Desoldering.
- Refit the power supply board: align its connector with the motherboard pins, set it down over the guide pins and press gently, fit the strip connector, refit the three screws, plug the harness on with the orange or purple wire towards the casting, and plug the short end of the RF cable into the power supply jack.[1]
Testing
[edit | edit source]- Save a short program to tape and load it back, or boot a disk.[2]
- Check +5 V on J204 pin 10 and +12 V on pin 12 against ground on pin 4.[1]
- Run the two POKE commands above and check that the recorder motor starts and stops.[2]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 Power Supply Repair
- Atari 800 Sound Repair
- Atari 800 Controller Port Repair
- Atari 400 SIO Port Repair
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 800 motherboard schematic (figures 2-6A and 2-6B, pp. 2-10 and 2-11: POKEY and PIA pins, R129, R159, R168-R174, C182-C188, Q107, L106, J115), 800 power supply schematic (figure 2-8, p. 2-13: J201, J204, C211), visual inspection (p. 4-21), 800 disassembly and assembly (pp. 4-9 to 4-12 and 4-18), 800 port test (pp. 7-33 and 7-34) and port test legend (table 7-3), 800 parts list (section 9: A101 C012294, A102 C014795 or C014812, Q107 MPS-A55 C014809, J204 C012995). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: cassette operation, preliminary service checks (main board), test equipment, and troubleshooting, "Cassette Save and Load". Scan on the Internet Archive.
- ↑ Best Electronics, "Atari 400 / 800 Computers" parts page: SALT 2.05 diagnostic cartridge TE15644 and external SIO shorting plug TE15639. Retailer listing.