Atari 800 Sound Repair

The Atari 800 makes sound in two places. POKEY (A101) produces the sound for the television and monitor: its audio output, pin 37, feeds an audio mixer built from two sections of the transistor array A104, and a 4.5 MHz sound oscillator built round Q106 that puts the sound on the RF signal. The mixed audio also goes to the monitor socket. The keyboard click and the console beeps come from a small speaker inside the console, driven by Q101 from pin 15 of the CTIA or GTIA (A301) on the CPU board.[1][2] Atari's 800 tone test and Sams' service data follow both paths and give the parts to check at each stage.[1][2]
Symptoms
[edit | edit source]- No sound from the television or monitor, while the picture is good.[2]
- Sound from a BASIC SOUND statement, but not from other programs: Sams points at POKEY.[2]
- No click from the console speaker when a key is pressed.[2]
- No sound at the monitor socket's audio pin, or no sound from a peripheral's audio track.[2][1]
Check the television first: Atari's chart ends by setting the RF modulator to channel 3, with the television tuned to channel 3, the fine tuning set for a clear picture and the volume up.[1] If the monitor socket gives sound and the television does not, the fault is on the RF side; see Atari 800 Video Output Repair.
Safety
[edit | edit source]The adaptor plugs into the mains. Unplug it before removing a board or chip, and use static precautions with the boards.[1]
Tools and parts
[edit | edit source]- An oscilloscope, a frequency counter with a pickup loop, a logic probe and a meter.[2]
- An alignment tool for L101; Sams lists GC Electronics 9300, 9302 and 9304.[2]
- Optional: SALT II, whose tone test (T) the flowchart uses.[1]
- Parts as found, from Atari's 800 parts list:[1]
| Position | Part | Atari number |
|---|---|---|
| A101 | POKEY | C012294 |
| A104 | Transistor array (audio mixer and colour circuit) | C010174 |
| Q106 | 2N3563 transistor (sound oscillator) | 34-2N3563 |
| L101 | Variable inductor, 0.6–1.2 µH | C010823 |
| L102 | Inductor, 2 µH | C010822 |
| C169, C173 | 820 pF | C010821 |
| R157, R166 | 1 kΩ | 14-5102 |
| R167 | 18 kΩ | 14-5183 |
| R195 | 4.7 kΩ | 14-5472 |
| C181 | 0.1 µF ceramic | C014181-03 |
| C178 | 0.001 µF ceramic | C014181-01 |
| C180 | 0.22 µF ceramic | C014181-05 |
| Q101 | 2N3904 transistor (speaker driver) | 34-2N3904 |
| CR101 | 1N914 diode | 31-1N914 |
| – | Speaker assembly, 63 Ω | CA011840 |
| A203 | RF module "B" (power supply board) | CA012174 |
Procedure
[edit | edit source]Open the machine
[edit | edit source]
- Turn the unit upside down, remove the five bottom cover screws and remove the bottom cover.[1]
- Remove the two screws from the casting flange and the single screw from the lower left corner of the power supply board, disconnect the speaker, turn the unit over, swing the top cover up and unplug the keyboard ribbon cable.[1]
- Unplug the RF cable and the power supply harness, remove the three power supply board screws and lift the board straight up.[1]
- Turn the unit upside down, remove the nine screws from the lower shield and lift the motherboard and lower shield out of the casting.[1] Sams' sequence separates the boards the same way, disconnecting J114 from J202 and J115 from J201 on the power supply board as the shield comes away.[2]
- POKEY (A101) is in a 40-pin socket and A104 in a 14-pin socket on the motherboard.[1]
No sound from the television or monitor
[edit | edit source]Sams' sequence, with the computer running:[2]
- Type in and run
10 SOUND 0,100,10,15: GOTO 10. - Check pin 37 of POKEY (A101) for the waveform in Sams' figure 1. If it is missing, check A101 by substitution.
- If the waveform is correct, check the frequency of the sound oscillator Q106: connect a pickup loop to the frequency counter and slip it over L101. It should read 4.5 MHz.
- If Q106 is not working, check the voltages and parts around it.
- If the monitor audio output alone is missing, check the connections at pin 2 of J201 and the voltages and parts around A104.
Atari's tone test with SALT II:[1]
- Press T and RETURN, enter the voice number (1 to 4) and press RETURN. Listen for all eight tones or speaker clicks; the first two tones are very high and may be inaudible, but the clicks from the DC level shifts can be heard.
- If the tones are missing, replace POKEY (A101) and test again.
- If they are still missing, lock SALT II into continuous mode, restart on voice 1 and put the scope on pin 37 (AUD) of A101. Each tone should show as a frequency that falls while the amplitude decays to 0 V.
- If not, or if the later steps of the test fail, check: R157 (1 kΩ) for a short; C181, R167 (18 kΩ) and R195 (4.7 kΩ) for an open circuit; and C178 (0.001 µF), C180 (0.22 µF) and R166 (1 kΩ) for a short or open circuit. The chart prints C181 as "1.uf"; the schematic and parts list give 0.1 µF.
- Check for 4.5 MHz oscillation at the emitter of Q106; Atari's figure is a sine wave about 2.3 cm long per cycle at 0.1 µs/div and 20 mV/div, and L101 must be adjustable to 4.5 MHz. If not, repair the oscillator.
- Check the input to the audio mixer at the collector, A104 pin 2 (0.5 ms/div, 5 mV/div). The waveform should match POKEY pin 37, rounded instead of square.
- Check for output on A104 pin 5 (0.5 ms/div, 50 mV/div). If there is none, replace A104 and test again.
- Adjust the RF modulator (A203) to channel 3, tune the television to channel 3 with the fine tuning set for a clear picture, turn the volume up and test again. Run the test for the other three voices.
Set the sound oscillator
[edit | edit source]Connect a pickup loop to the input of a frequency counter, slip it over L101 and adjust L101 for 4.5 MHz.[2]
No click from the console speaker
[edit | edit source]Sams' sequence:[2]
- Check the speaker SP101. If it is good, type in and run
10 PRINT CHR$(253): GOTO 10. - Check for pulses of about 1.4 V peak to peak at pin 15 of the CTIA or GTIA (A301). If they are missing, check A301 by substitution.
- If they are present, check for pulses of about 0.5 V peak to peak at the base of Q101. If they are missing, check R102 and Q101.
- If the pulses reach Q101, check Q101, the diode CR101, R101 and the 5.1 V supply.
On the schematic Q101's base is fed from the CTIA line through R102 (1 kΩ), and the speaker connects to the two-pin header J105.[1] Atari's console switch test uses the same speaker: if it does not beep when a console key is pressed, the chart checks R184 to R187 and C165.[1]
Peripheral audio dead
[edit | edit source]The audio input from a recorder or other peripheral comes in on pin 11 of the peripheral socket J204, passes C211 (10 µF) on the power supply board and reaches the motherboard on J201 pin 13.[1] Check those connections, then the mixer A104. See Atari 800 SIO Port Repair.
Reassemble
[edit | edit source]Refit the boards in the reverse order, as in Atari 800 Power Supply Repair: the motherboard and lower shield into the casting with nine screws, the power supply board with its three screws, the strip connector and harness (orange or purple wire towards the casting), the RF cable, the module into the top cover with the keyboard harness, the speaker (foam side down, no polarity) and the bottom cover with five screws.[1]
Testing
[edit | edit source]- Run
10 SOUND 0,100,10,15: GOTO 10and listen to the television and to the monitor socket's audio.[2][1] - Type at the keyboard and listen for the click from the console speaker.[2]
- With SALT II, run the tone test on all four voices.[1]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 Keyboard Repair
- Atari 800 Video Output Repair
- Atari 800 SIO Port Repair
- Atari 800 Power Supply Repair
- Atari 400 Sound Repair
- Continuity Testing and Signal Tracing
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 800 motherboard schematic (figures 2-6A and 2-6B, pp. 2-10 and 2-11: Q101, R101-R103, J105, Q106, L101, L102, A104, R157-R195, C169-C181, J115), 800 power supply schematic (figure 2-8, p. 2-13: J201, J204, J205, C211, A203), 800 disassembly and assembly (pp. 4-9 to 4-13 and 4-17 to 4-19), 800 tone test (pp. 7-24 to 7-27), 800 console switch test (p. 7-28), 800 parts list (section 9: A101 C012294, A104 C010174, Q106 2N3563, L101 C010823, L102 C010822, C169 and C173 C010821, Q101 2N3904, speaker CA011840, RF module "B" CA012174). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: test equipment, disassembly instructions ("Shield Removal"), troubleshooting, "Audio", and miscellaneous adjustments ("Sound Adjustment", alignment tools). Scan on the Internet Archive.