Atari 800 Keyboard Repair

The Atari 800 has a full-travel keyboard in the top cover, connected by a ribbon cable to the keyboard connector J106 on the motherboard.[1] POKEY (A101) scans it through two CD4051 multiplexers: Z103 ("key out") drives the row lines and Z104 ("key in") reads the columns back to POKEY. BREAK, CONTROL and the SHIFT keys have a column of their own that goes straight to POKEY pin 16.[1][2] The four console keys are separate: SYSTEM RESET, OPTION, SELECT and START are push switches (S204 to S207) on the power supply board, wired through J202, a cable to J114 on the motherboard and the resistors R184 to R187 to the CPU board connector.[1] POKEY, Z103 and Z104 are in sockets.[1]
Atari's parts list gives two versions of the keyboard assembly, CA012952-01 with a white ribbon and CA012952-02 with a multicoloured ribbon.[1] Len Spencer, writing in 1991, described two constructions: a full-stroke keyboard with separate contact switches, of which Stackpole was a major maker, and a printed-contact keyboard with conductive-paint traces on plastic sheets, which his own Mitsumi-made 800 used.[3] Best Electronics recondition 800 keyboards of the Hi Tek and Stackpole types and do not accept Mitsumi ones for exchange.[4]
Symptoms
[edit | edit source]- One key does not work: Sams says to substitute the keyboard; Atari's chart replaces it when only some keys fail.[2][1]
- Several keys, or a whole row or column, do not work: J106, POKEY and the multiplexers Z103 and Z104.[2]
- No key works, although the ATARI COMPUTER - MEMO PAD screen appears: swap A101, Z103 and Z104.[1]
- A key sticks on and repeats.[3]
- START, SELECT, OPTION or SYSTEM RESET do not work.[2][4]
- No click from the console speaker when a key is pressed: see Atari 800 Sound Repair.[2]
Start with Atari's no-tools check: with no cartridge fitted, switch on, press every key at the Memo Pad and watch for each on the screen, including CONTROL with other keys. One failed key is probably the keyboard; more than one needs the tests below.[1] A blank or coloured screen with no Memo Pad is a different fault; see Atari 800 Black Screen Repair.
Safety
[edit | edit source]Unplug the power adaptor before opening the case. Do not overtighten the screws in the plastic and aluminium parts (Atari gives 6 inch-pounds for plastic and 10 for aluminium) and use static precautions with the boards.[1]
Tools and parts
[edit | edit source]- A cross-head screwdriver, a logic probe and an oscilloscope.[2]
- Optional: SALT II for the keyboard and switch tests; Best Electronics sells SALT 2.05 (TE15644).[1][4]
- Spare chips for swapping: CD4051B (Atari C014336) for Z103 and Z104, POKEY (C012294) for A101.[1]
- For the console keys: the pushbutton switch CA011620-01 (or -02) for S204 to S207.[1]
- A replacement or reconditioned keyboard (CA012952).[1][4]
- For a printed-contact keyboard: conductive paint for broken traces and thin clear tape for the separator sheet.[3]
Procedure
[edit | edit source]Open the machine and remove the keyboard
[edit | edit source]- Turn the unit upside down, remove the five bottom cover screws and tilt the back of the bottom cover up and towards you to remove it.[1]
- Remove the two screws from the aluminium casting flange and the single screw from the lower left corner of the power supply board. Disconnect the speaker cable and set the speaker aside.[1]
- Turn the unit over and carefully pull the back of the top cover up to 90°, separating it from the PCB module. Reach over the top cover and unplug the keyboard's ribbon cable, then set the top cover aside.[1]
- Turn the top cover upside down, remove the four screws from the corners of the keyboard and lift the keyboard out.[1]
Find which line has failed
[edit | edit source]
- Note the keys that fail at the Memo Pad or in the SALT II keyboard test (K and RETURN; failed keys show in red).[1]
- Find them in the table. Keys that share a J106 pin and all fail point at that line: its contact in the connector, its track or cable, or its multiplexer pin. Scattered single keys point at the keyboard itself.[1]
| J106 pin | Line goes to | Keys |
|---|---|---|
| 1 | Z103 pin 14 | BREAK, 7, 8, 9, 0, CLEAR, INSERT, DELETE |
| 2 | Z103 pin 1 | ESC, 1, 2, 3, 4, 5, 6 |
| 3 | Z103 pin 2 | U, I, O, P, −, =, RETURN |
| 4 | Z103 pin 15 | TAB, Q, W, E, R, T, Y |
| 5 | Z103 pin 4 | CONTROL, J, K, L, semicolon, +, * |
| 6 | Z103 pin 13 | CAPS/LOWR, A, S, D, F, G, H |
| 7 | Z103 pin 12 | N, M, comma, full stop, /, Atari key, SPACE BAR |
| 8 | Z103 pin 5 | Both SHIFT keys, Z, X, C, V, B |
| 9 | POKEY (A101) pin 16 | BREAK, CONTROL, both SHIFT keys |
| 10 | Z104 pin 1 | 6, 7, Y, U, N |
| 11 | Z104 pin 2 | H, J, SPACE BAR |
| 12 | Z104 pin 15 | 5, 8, T, I, G, K, B, M |
| 13 | Z104 pin 4 | 4, 9, R, O, F, L, V, comma |
| 14 | Z104 pin 5 | 3, 0, E, P, D, semicolon, C, full stop |
| 15 | Z104 pin 14 | 2, CLEAR, W, −, S, +, X, / |
| 16 | Z104 pin 13 | 1, INSERT, Q, =, A, *, Z, Atari key |
| 17 | Z104 pin 12 | ESC, DELETE, TAB, RETURN, CAPS/LOWR |
Keys dead on the board side
[edit | edit source]
Sams' sequence, with the keyboard reconnected and the computer showing a proper screen:[2]
- Check the waveforms on pins 18 to 23 of POKEY (A101). If they are missing, check A101 by substitution.
- If they are correct, check the waveforms on POKEY pins 16 and 25 while pressing keys, and check pin 29 with a logic probe for a pulse when any key is pressed. Pin 16 shows a waveform when BREAK, CONTROL or SHIFT is pressed; pin 25 shows one for every other key except SYSTEM RESET, OPTION, SELECT and START.
- If the waveform at pin 16 or 25 is missing, check the voltages and logic probe readings on pins 1 to 16 of Z103 and Z104. If they are wrong, check A101, Z103 and Z104 by substitution. If they are correct, check J106 and the keyboard switch contacts.
- If no pulse appears at pin 29 when a key is pressed, check A101 by substitution.
Atari's chart for all keys failing is the same: swap A101, Z103 and Z104. It shows a typical stepped waveform at Z104 pin 14 and pulses at Z104 pin 3 with the W key held down.[1] Len Spencer's advice was to swap the two 4051s one at a time.[3] The keyboard lines pass through the 100 Ω resistors R110 to R126, with .001 µF capacitors C105 to C121 to ground.[1]
Repair the keyboard
[edit | edit source]Spencer's notes, from his own repairs:[3]
- Full-stroke (Stackpole) keyboard: clean a dead key with a good tuner cleaner. If that does not cure it, replace the key switch.
- Printed-contact (Mitsumi) keyboard: do not use any solvent cleaner, which washes the traces off; even alcohol discolours them and raises their resistance. Clean with a little water and a soft cloth only.
- Repair a broken trace with a dab of conductive paint. See Keyboard Membrane Trace Repair.
- If a key still does not work, stretch its pressure spring a little. Stretch it gradually: it is easier to stretch a spring than to shorten it, and cutting it is not acceptable.
- If a key sticks on, try it with the pressure spring removed. If it then stops repeating, shorten the spring by squeezing it gently.
- If it still sticks, put a piece of thin clear tape over that key's hole in the separator sheet and cut the tape out over the hole. Do not use masking tape, and do not use more than two layers; if two layers do not cure it, replace the keyboard.
- Spencer notes that the 800's 18-pin connector is a full plastic-bodied type, which he contrasts with the 800XL, whose keyboard ribbon is an extension of the printed sheet itself.
Console keys dead
[edit | edit source]
- Put the logic probe on pins 12, 13 and 14 of the CTIA or GTIA (A301) and pin 6 of ANTIC (A302) and press the faulty key. If a reading stays high when the key is pressed, check the connectors J114 and J202. If the readings are correct, check A301 and A302 by substitution.[2]
- Atari's console switch test (S and RETURN on SALT II, then each key): if the console speaker does not beep when a console key is pressed, check R184 to R187 and C165 for a short or an open circuit; if it does beep, replace the CTIA or GTIA (A301) on the CPU board.[1]
- On the schematic J202 pin 1 is RESET (S204), pin 2 OPTION (S205), pin 3 SELECT (S206) and pin 4 START (S207), each switch closing its line to ground.[1]
- The switches themselves wear out: Best Electronics records an 800 whose SELECT and START did not work being cured by replacing all four console switches on the power supply board.[4] To reach them, remove the power supply board as described in Atari 800 Power Supply Repair.
Refit the keyboard
[edit | edit source]- Set the top cover upside down with the keyboard in it and refit the four screws. Check that the space bar and keys do not bind.[1]
- Set the top cover upside down, invert the module assembly and lower it in, turning the cartridge door latches inwards to clear the cover. Keep the RF cable from being trapped between the power supply board and the top cover standoff.[1]
- Lift the motherboard an inch out of the top cover and plug in the keyboard harness. Refit the two screws in the front holes of the casting.[1]
- Set the speaker in its receptacle foam side down and reconnect it (no polarity). Fit the bottom cover, with the RF cable out through its hole, and refit the five screws.[1]
Testing
[edit | edit source]- Press every key at the Memo Pad, including CONTROL with other keys.[1]
- With SALT II, run the keyboard test (K and RETURN) and the switch test (S and RETURN; press START, SELECT, OPTION and SYSTEM RESET in that order).[1]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 Power Supply Repair
- Atari 800 Sound Repair
- Atari 400 Keyboard Repair
- Keyboard Membrane Trace Repair
- Switch and Potentiometer Repair
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 800 motherboard (p. 1-14: Z103 and Z104), 800 motherboard schematic (figures 2-6A and 2-6B, pp. 2-10 and 2-11: J106, Z103, Z104, A101, R110-R126, C105-C121, R184-R187, J114), 800 power supply schematic (figure 2-8, p. 2-13: J202, S204-S207), power-up, keyboard and switch tests (pp. 3-2 and 3-9), 800 disassembly and assembly (pp. 4-1, 4-9 to 4-14 and 4-17 to 4-19), 800 keyboard chart (pp. 7-22 and 7-23), 800 console switch test (p. 7-28), keyboard connection chart (p. 5-38), 800 parts list (section 9: keyboard CA012952-01 and -02, Z103-104 C014336, A101 C012294, switches S204-207 CA011620-01 or -02). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: preliminary service checks ("Keyboard"), test equipment, and troubleshooting, "Keyboard". Scan on the Internet Archive.
- ↑ 3.0 3.1 3.2 3.3 3.4 Len Spencer, "The Workbench" (reprinted from the Mid-Florida Atari Computer Club Bulletin), Z*Magazine issue 192, 24 April 1991. Text at textfiles.com. Community article.
- ↑ 4.0 4.1 4.2 4.3 4.4 Best Electronics, "Atari 400 / 800 Computers" parts page: reconditioned 800 keyboard CA012952 (Hi Tek and Stackpole types accepted for exchange, Mitsumi not), SALT 2.05 TE15644, and a customer's 800 with SELECT and START not working, cured by four new console switches. Retailer listing.