Atari 800 Black Screen Repair

An Atari 800 that switches on to a black or grey screen, with no ATARI COMPUTER - MEMO PAD, has stopped before the 6502 could run the operating system, or is not producing a picture at all. Atari's power-up chart for this symptom checks, in order, the −5 V and +12 V supplies, the clock circuit, the reset voltages at ANTIC and the 6502, the CTIA or GTIA, and then a short list of motherboard parts.[1] Sams' service data adds checks on the 6502's supply, clock and bus activity, and on the crystal frequency.[2] The CPU board, which carries the 6502 (A303), ANTIC (A302) and the CTIA or GTIA (A301), plugs into the motherboard connector J101; the crystal oscillator and the reset circuit are on the motherboard.[1]
Symptoms
[edit | edit source]- A black or grey screen at switch-on.[1]
- Other screen colours have their own charts: a snowy screen points at the RF path, a green or yellow screen at the RAM boards and the operating system ROMs, and a solid blue screen at POKEY.[1] See Atari 800 Power Supply Repair, Atari 800 Operating System ROM Replacement and the Atari 800 Troubleshooting Guide.
- A picture that appears but has no sync or no colour is a video fault; see Atari 800 Video Output Repair.
Safety
[edit | edit source]- The power pack plugs into the mains. Remove the power before servicing; Sams says never to remove or install boards with the power on.[2]
- Atari's notes call for all static control precautions when handling a circuit board. Sams adds an earthed wrist strap, to be taken off before the unit is powered for testing.[1][2]
Tools and parts
[edit | edit source]- A digital meter, a logic probe and a frequency counter, as Sams lists, and an oscilloscope for Atari's clock table.[2][1]
- A known-good CPU board and 16K RAM board, if available: Sams' first substitutions for an 800 that will not come up.[2]
- Parts as found: 2N3906 transistors for Q102 and Q103, the 3.579575 MHz crystal X101 (Atari C010177), the CD4050 for A103 (C010816), and the 6502 for A303 (C014377).[1][3]
Procedure
[edit | edit source]Check the supplies
[edit | edit source]
- Check for −5 V at J201 pin 1. If it is missing, Atari's chart names a voltage regulator, CR204 and CR205 (replace 1N4001-type diodes with 1N5391, Atari C017988), and C203 to C205 and C212.[1] On the schematic and in Sams' checks, −5 V comes from the zener CR201 fed through CR202, CR203, C201 and C202, with the power LEDs CR210 and CR211 and resistors R201 and R202 in the same circuit, so check those parts as well.[1][2]
- Check for +12 V at J201 pin 21. If it is missing, check the regulator A201, CR204 and C203 to C205.[1]
- Check for 5.1 V at pin 8 of the 6502 (A303), its supply pin. If it is missing, go to the power supply checks in Atari 800 Power Supply Repair.[2]
Open the machine
[edit | edit source]- Remove the bottom cover (five screws), the two casting flange screws and the power supply board's lower left screw, disconnect the speaker, swing the top cover up, unplug the keyboard cable and set the top cover aside.[1]
- Unplug the RF cable and the power supply harness, remove the three power supply board screws and lift the board straight up.[1]
- Turn the unit upside down, remove the nine screws from the lower shield and lift the motherboard and lower shield out of the aluminium casting. The CPU board can then be removed.[1]
Follow the clock
[edit | edit source]
Atari's note to the chart: start at the top of Table 7-1 and trace back until the clock signal appears, which shows which part has failed.[1]
| Point | Board | Frequency (MHz) |
|---|---|---|
| Pins 21 and 22 of J101 | CPU | 1.789 |
| Pins 8, 9, 10 and 13 of Z302 | CPU | 1.789 |
| Pin 37 of A303 (6502) | CPU | 1.140 (as printed) |
| Pin 6 of Z301 | CPU | 1.789 |
| Pin 34 of A302 (ANTIC) | CPU | 1.789 |
| Pin 35 of A302 (ANTIC) | CPU | 3.579 |
| Pins 29 and 28 of A301 (CTIA or GTIA) | CPU | 3.579 |
| Collector of Q102 | 800 motherboard | 3.579 |
| Pin 7 of A101 (POKEY) | Motherboard | 1.789 |
| Pin 25 of A102 (PIA) | Motherboard | 1.789 |
Sams' sequence for the same circuit:[2]
- Check the waveform at pin 37 of the 6502 (A303). If it is missing, check the waveform at the collector of the clock transistor Q102.
- If the waveform at Q102's collector is missing, check the voltages and parts around Q102 and Q103. Put a frequency counter on Q102's collector: it should read 3.57957 MHz. If the frequency is wrong, check the crystal X101 by substitution.
- If Q102's collector is good, check the waveform at pin 30 of the CTIA (A301), as Sams prints it. If it is missing, check A301 by substitution.
- If the clock at pin 37 of A303 is good, check the logic probe readings on pins 2, 3, 4, 6, 7, 34, 38, 39 and 40 of A303 against Sams' logic chart.
Check the processor is running
[edit | edit source]- Put the logic probe on pins 9 to 20 and 22 to 33 of the 6502 (A303), its address and data lines. They should all be pulsing.[2]
- Check for +5 V on the reset pins of ANTIC (A302, pin 36) and the 6502 (A303, pin 40). If either is low, repair the reset circuit.[1]
- On the motherboard the power-on reset comes from the CD4050 section A103A, with R154 (1 MΩ), R155 (100 kΩ), R156 (470 kΩ), the diode CR102 and C198 (0.1 µF), and goes to the CPU board on J101 pin 25 (RESET M).[1]
Swap the chips
[edit | edit source]- If the clock and reset are good, replace the CTIA or GTIA (A301).[1]
- If the screen is still black or grey, swap the clock circuit parts, Z101 to Z104 and ROM F on the operating system board for known-good parts.[1] Z101 is a 74LS42 decoder, Z102 a 74LS32, and Z103 and Z104 the 4051 keyboard multiplexers, all in 16-pin sockets; ROM F is A401 on the ROM module.[1]
- If there is still no Memo Pad, Atari's chart moves to the green or yellow screen chart, which checks the RAM boards and then the ROMs; see Atari 800 Operating System ROM Replacement.[1]
- Sams' preliminary checks put the order differently: with the supply and crystal good, substitute the CPU board and the 16K RAM boards, then the personality (ROM) board. If the computer comes up wrongly, Sams lists the decoder Z101, the data buffers Z105 and Z106, and Z102.[2]
Intermittent lock-ups
[edit | edit source]Atari's Tech Tip 10 gives a burn-in of at least 12 hours on the continuous RAM test of the SALT 2.05 cartridge, followed by six presses of SYSTEM RESET. If the unit fails, check the wiring and connectors between the power supply and the motherboard and where the ROM, RAM and CPU boards plug in, look for cold solder joints, and replace the 6502 (C014377). If it still fails, the tip lists ANTIC (C012296), the GTIA (C014805) and the multiplexers on the RAM boards (C014345, with matching vendor and date codes) as the next parts to replace.[3]
Reassemble
[edit | edit source]- Clean and lubricate the CPU, RAM and ROM board contacts before refitting them, as Atari's assembly notes require.[1]
- Plug in the CPU board with its component side facing away from the plastic cartridge guide, firmly seated. Turn the aluminium casting over, turn the motherboard upside down and set it with the lower shield into the casting, with the CPU board in its slot in the casting. Fit the nine lower shield screws.[1]
- Refit the power supply board over the motherboard pins, its strip connector and three screws, then the harness, with the orange or purple wire towards the casting, and the RF cable.[1]
- Refit the module into the top cover, plug in the keyboard harness, fit the two front casting screws and the speaker, and fit the bottom cover with its five screws, making sure the RF cable is not trapped.[1]
Testing
[edit | edit source]- Switch on with no cartridge: the words ATARI COMPUTER - MEMO PAD should appear.[1]
- Press SYSTEM RESET several times; each press should bring the Memo Pad back.[3]
- Recheck the clock frequencies in Table 7-1.[1]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 Power Supply Repair
- Atari 800 Video Output Repair
- Atari 800 Operating System ROM Replacement
- Atari 800 RAM Replacement
- Atari 400 Black Screen Repair
- Edge Connector and Cartridge Slot Cleaning
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 800 motherboard (p. 1-14: CPU connector J101), 800 motherboard schematic (figure 2-6B: X101, Q102, Q103, A103A, R154-R156, CR102, C198, J101), 800 power supply schematic (figure 2-8, p. 2-13), power-up test (p. 3-2), notes and 800 disassembly and assembly with contact cleaning (pp. 4-1 to 4-3, 4-9 to 4-12 and 4-17 to 4-21), 800 black or grey screen charts (pp. 7-4 and 7-5), other 800 power-up charts (pp. 7-3, 7-6 and 7-7), clock circuit table 7-1 (p. 7-36), 800 parts list (section 9: X101 C010177, A103 C010816 CD4050, Q102-103 2N3906, Z101 74LS42, Z102 74LS32, Z103-104 4051B, Z105-106 74LS243, A303 C014377). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: test equipment and tools, preliminary service checks, safety precautions, and troubleshooting guide, "Power Supply", "CPU Operation" and "Color Oscillator". Scan on the Internet Archive.
- ↑ 3.0 3.1 3.2 Atari, Inc., Consumer Product Service, Tech Tip 10, "Atari 400/800 System Lock-up", 22 February 1983 (burn-in test, connector and solder checks, 6502 C014377; further parts ANTIC C012296, GTIA C014805 and RAM board multiplexers C014345). Reproduced in File:Atari 400 800 Field Service Manual June 82.pdf, PDF pages 215 to 217.