Jump to content

Atari 400 Black Screen Repair

From RetroTechCollection
Atari 400 clock oscillator X101 Q103 Q104 and motor switch Q102 (Field Service Manual figure 2-2B)
Atari's schematic of the 400 clock oscillator on the motherboard: the 3.579575 MHz crystal X101 with the transistors Q103 and Q104 and resistors R155 to R158. The cassette motor switch Q102 is beside it.

An Atari 400 that switches on to a black or grey screen, with no ATARI COMPUTER - MEMO PAD, has stopped before the 6502 could run the operating system, or is not producing a picture at all. Atari's power-up chart for this symptom checks, in order, the −5 V and +12 V supplies, the clock circuit on the CPU board, the reset voltages at ANTIC and the 6502, the CTIA or GTIA, and then a list of motherboard parts.[1] Sams' service data adds checks on the 6502's clock, supply and bus activity, and the crystal frequency.[2] The CPU board, which carries the 6502 (A303), ANTIC (A302) and the CTIA or GTIA (A301), plugs into the motherboard connector J110; the crystal oscillator is on the motherboard.[1]

Symptoms

[edit | edit source]

Safety

[edit | edit source]
  • The adaptor plugs into the mains. Unplug it before removing or fitting any board or chip.[1]
  • The custom chips (ANTIC, the CTIA or GTIA and POKEY) are no longer made; swap them only into a board that has passed the supply checks.

Tools and parts

[edit | edit source]
  • A digital meter, a logic probe, an oscilloscope and a frequency counter.[2]
  • A known-good CPU board and 16K RAM board, if available: Sams' first substitutions for a 400 that will not come up.[2]
  • Parts as found: 2N3906 transistors for Q103 and Q104, the 3.579575 MHz crystal X101 (Atari C010177), CD4050 for A111 (C010816), and the 6502 for A303 (C014377).[1][3]

Procedure

[edit | edit source]

Open the machine

[edit | edit source]
  1. Remove the top cover, keyboard and power supply board as described in Atari 400 Power Supply Repair.[1]
  2. Disconnect and remove the speaker assembly and lift the module assembly out of the bottom cover. Close and latch the cartridge door, set the module on its back, remove the eight screws from the bottom shield and lift it off.[1]
  3. Lift the motherboard assembly out of the aluminium casting. The CPU and RAM boards unplug from the motherboard.[1]

Check the supplies

[edit | edit source]
  1. Check for −5 V at J201 pin 18. If it is missing, check, repair or replace the bridge diodes CR206 to CR209 (replace 1N4001-type diodes with 1N5391, Atari C017988), CR201 to CR203, C201, C202 and C210.[1]
  2. Check for +12 V at J201 pin 2. If it is missing, check the regulator A201, CR204 and C203 to C205.[1]
  3. Check for 5.08 V at pin 8 of the 6502 (A303), its supply pin. If it is missing, go to the power supply checks in Atari 400 Power Supply Repair.[2]

Follow the clock

[edit | edit source]
Atari 400 CPU board and 16K RAM card (Knurrikowski)
An Atari 400 CPU board (left, marked C015500 REV 5) with its three 40-pin chips, the 6502, ANTIC and the CTIA or GTIA, and a 16K RAM card (right). Photo: Knurrikowski, CC BY-SA 4.0.

Atari's note to the chart: start at the top of Table 5-1 and trace back until the clock signal appears, which shows which part has failed.[1]

Clock check points on the 400 (Atari table 5-1)
Point Board Frequency (MHz)
Pins 21 and 22 of J101 CPU 1.789
Pins 8, 9, 10 and 13 of Z302 CPU 1.789
Pin 37 of A303 (6502) CPU 1.140 (as printed)
Pin 6 of Z301 CPU 1.789
Pin 34 of A302 (ANTIC) CPU 1.789
Pin 35 of A302 (ANTIC) CPU 3.579
Pins 29 and 28 of A301 (CTIA or GTIA) CPU 3.579
Collector of Q104 400 motherboard 3.579
Pin 7 of A101 (POKEY) Motherboard 1.789
Pin 25 of A102 (PIA) Motherboard 1.789

[1]

Sams' sequence for the same circuit:[2]

  1. Check the waveform at pin 37 of the 6502 (A303). If it is missing, check the waveform at the collector of the clock transistor Q104.
  2. If the waveform at Q104's collector is missing, check the voltages and parts around Q103 and Q104. Put a frequency counter on Q104's collector: it should read 3.579575 MHz, the frequency of the crystal X101.
  3. If Q104's collector is good, check the waveform at pin 30 of the CTIA (A301), as Sams prints it. If it is missing, check A301 by substitution.
  4. If the clock at pin 37 of A303 is good, check the logic probe readings on pins 2, 3, 4, 6, 7, 34, 38, 39 and 40 of A303 against Sams' logic chart.

Check the processor is running

[edit | edit source]
  1. Put the logic probe on the data lines of the 6502 (A303), pins 26 to 33, and the address lines, pins 9 to 20 and 22 to 25. They should all be pulsing.[2]
  2. Atari's chart checks for +5 V on the reset pin of ANTIC (A302, pin 36) and of the 6502 (A303). The chart prints the 6502 pin as 30; Atari's own MPU pin-assignment figure puts RES on pin 40 and data line D3 on pin 30, so measure the reset level at pin 40. If the reset lines are not at +5 V, repair the reset circuit.[1]
  3. On the motherboard the power-on reset comes from the CD4050 section A111F, with R181 to R183, C189 and the diode CR103, and goes to the CPU board on J110 pin 25 (RESM).[1]

Swap the chips

[edit | edit source]
  1. If the clock and reset are good, replace the CTIA or GTIA (A301).[1]
  2. If the screen is still black or grey, swap A103, A111, Z103 to Z105, Q103, Q104 and X101 on the motherboard.[1]
  3. If that does not cure it, check and replace the discrete parts in the video summing circuit; see Atari 400 Video Output Repair.[1]
  4. Sams' preliminary checks put the order slightly differently: with the supply and crystal good, substitute the CPU board and the 16K RAM board, then ROMs A103 and A104, the video buffer A111 and the decoders Z103 and Z104.[2]

Intermittent lock-ups

[edit | edit source]

Atari's Tech Tip 10 gives a burn-in of at least 12 hours on the continuous RAM test of the SALT 2.05 cartridge, followed by six presses of SYSTEM RESET. If the unit fails, check the wiring and connectors between the power supply and the motherboard and where the ROM, RAM and CPU boards plug in, look for cold solder joints, and replace the 6502 (C014377). If it still fails, the tip lists ANTIC (C012296), the GTIA (C014805) and the multiplexers on the RAM boards (C014345, with matching vendor and date codes) as the next parts to replace.[3]

Reassemble

[edit | edit source]
  1. Clean and lubricate the CPU and RAM board contacts before refitting them, as Atari's assembly notes require.[1]
  2. Insert the RAM and CPU boards into the motherboard with their component sides facing away from you, set the aluminium casting upside down, invert the motherboard and lower it in, with the CPU board in its guides.[1]
  3. Refit the lower shield with eight screws, the module, the speaker, the keyboard, the power supply board and the top cover as in Atari 400 Power Supply Repair.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge: the words ATARI COMPUTER - MEMO PAD should appear.[1]
  2. Press SYSTEM RESET several times; each press should bring the Memo Pad back.[3]
  3. Recheck the clock frequencies in Table 5-1.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: MPU pin assignments (figure 1-3, p. 1-8), 400 motherboard schematic (figure 2-2B, p. 2-5: X101, Q103, Q104, R155-R158, A111F, R181-R183, C189, CR103, J110), power-up test (p. 3-2), 400 disassembly and assembly with contact cleaning (pp. 4-1 to 4-6, 4-15 to 4-17 and 4-20 to 4-21), 400 black or grey screen charts (pp. 5-4 and 5-5), other power-up charts (pp. 5-3, 5-6 and 5-7), clock circuit table 5-1 (p. 5-36), 400 parts list (section 9: X101 C010177, A111 C010816, Q103-104 2N3906). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Howard W. Sams & Co., Computerfacts CC5, Atari Model 400, 1984: test equipment, preliminary service checks (main board), and troubleshooting guide, "CPU Operation" and "Crystal Oscillator". Scan on the Internet Archive.
  3. ↑ 3.0 3.1 3.2 Atari, Inc., Consumer Product Service, Tech Tip 10, "Atari 400/800 System Lock-up", 22 February 1983 (burn-in test, connector and solder checks, 6502 C014377; further parts ANTIC C012296, GTIA C014805 and RAM board multiplexers C014345). Reproduced in File:Atari 400 800 Field Service Manual June 82.pdf, PDF pages 215 to 217.