Jump to content

Atari 400 Video Output Repair

From RetroTechCollection
Atari 400 video buffers A111, colour amplifier Q107 and reset buffer (Field Service Manual figure 2-2B)
Atari's schematic of the 400 video circuit: the luminance and sync lines arrive from the CPU board on J110 (right), pass through the CD4050 buffers A111A to A111E and the summing resistors R176 to R180, and the colour signal is amplified by Q107 (left)

The Atari 400 has one video output, the RF socket J203 on the power supply board; there is no monitor socket.[1] The picture is made by the CTIA or GTIA (A301) and ANTIC (A302) on the CPU board. Four luminance lines, the composite sync and the colour signal come down the CPU board connector J110 to the motherboard, where the CD4050 buffer A111 and a resistor ladder sum the luminance and sync, and the transistor Q107 amplifies the colour. The combined signal leaves the motherboard on J107 pin 1, reaches the power supply board on J201 pin 1 and goes into the RF modulator A203.[1][2] Atari's colour bar and grey bar flowcharts and Sams' service data follow this path stage by stage.[1][2]

Symptoms

[edit | edit source]
  • A snowy screen with no picture. Atari's checklist gives the switch box, the AC adaptor, the channel select switch, the modulator adjustment and RF cable damage; see also Atari 400 Power Supply Repair.[1]
  • A picture with no colour, or with wrong colours.[2]
  • A picture that rolls or tears: no vertical or horizontal sync.[2]
  • Missing or wrong grey bars on the SALT II grey bar test.[1]

A black, blue, green or yellow screen at switch-on, with no Memo Pad, is a power-up fault; see Atari 400 Black Screen Repair and the Atari 400 Troubleshooting Guide.

Safety

[edit | edit source]

The adaptor plugs into the mains; unplug it before opening the case or removing a board. If a CRT television is opened during fault-finding, follow CRT Discharge Procedure.

Tools and parts

[edit | edit source]
  • An oscilloscope, a frequency counter, a logic probe and a digital meter.[2]
  • A television tuned to channel 2 or 3, and an alignment tool for the modulator coil; Sams lists GC Electronics 9300, 9302 and 9304.[2]
  • Optional: SALT II, whose colour bar (C) and grey bar tests the flowcharts use.[1]
  • Parts as found: CD4050 buffer for A111 (Atari C010816), 2N3904 transistor for Q107, 2N3906 transistors for Q103 and Q104, the 3.579575 MHz crystal X101 (C010177), and the RF module "B" A203 (CA012174).[1]

The video path

[edit | edit source]
Atari 400 luminance and sync lines (Atari figure 2-2B)
Signal J110 pin A111 input A111 output Summing resistor
LM0 1 11 12 R180, 62 kΩ
LM1 3 9 10 R178, 30 kΩ
LM2 2 7 6 R177, 15 kΩ
LM3 M 3 2 R179, 120 kΩ
Composite sync B 5 4 R176, 12 kΩ
Colour 4 – – To Q107 through R175 (3.3 kΩ) and C187 (10 pF)

[1]

Atari's parts list gives R176 as 15 kΩ and R177 as 12 kΩ, the reverse of the schematic; check the board before replacing either.[1]

Procedure

[edit | edit source]

Check the television connection first

[edit | edit source]

Sams' RF modulator check:[2]

  1. Switch on and check that the power LED (CR210) lights. If it does not, see Atari 400 Power Supply Repair.
  2. Check that the channel select switch S201 is on the same channel as the television, 2 or 3.
  3. Check that the TV/computer switch in the switch box is set to computer.
  4. Check for bad connections and wrong hook-up at the television and at the computer.
  5. If there is still no picture, check the voltages at the RF modulator's connections; if they are correct, substitute the modulator.

Open the machine

[edit | edit source]
  1. Remove the four screws from the bottom, open the cartridge door and remove the top cabinet. Unplug the RF modulator cable and remove the bottom of the cabinet.[2]
  2. Remove the keyboard screw and unplug the keyboard, remove the two power supply screws and the interlock switch plunger, and lift the power supply board off.[1][2]
  3. Remove the eight screws from the shield and remove the top and bottom shields.[2] The CPU board plugs into J110 on the motherboard; A111 is in a 16-pin socket on the motherboard.[1]

No picture

[edit | edit source]

Sams' sequence, from the modulator back to the CTIA:[2]

  1. Check for a video waveform at pin 1 of J201. If it is there, check the RF modulator.
  2. If it is missing, check the waveforms and voltages on the video buffers, pins 2, 3, 6, 7 and 9 to 12 of A111, and the sync buffer, pins 4 and 5 of A111. Each buffer's output waveform should match its input.
  3. If a waveform is missing at a buffer output, check A111.
  4. If a waveform is missing at a buffer input, check the connections at J110 pins 1, 2, 3, B and M, then the voltages, waveforms and logic probe readings on pins 1 to 40 of the CTIA (A301), and check A301 by substitution.

No sync

[edit | edit source]
  1. Check the waveform at pin 25 of the CTIA (A301). If it is missing, check A301 by substitution.[2]
  2. If it is correct, check the voltages and waveforms on the sync buffer, pins 4 and 5 of A111, and check R176.[2]

No colour or wrong colour

[edit | edit source]
Atari 400 colour bar troubleshooting with scope waveforms (Field Service Manual page 5-11)
Atari's colour bar troubleshooting chart, with the expected scope waveform beside each check: 3.58 MHz at R158, the input to Q107's base, the output from its collector and the signal at J107 pin 1

Sams' sequence:[2]

  1. Check for a colour waveform at pin 21 of the CTIA (A301).
  2. If it is missing, check the colour adjustment R309 on the CPU board. The voltage at pin 17 of A301 should vary from about 7 V to 0 V as R309 is turned from minimum to maximum. If it does not change, check R309, C305, R308 and the 12.20 V supply, and check A301 by substitution (Sams prints "IC301").
  3. If R309 is working, check the waveform at pin 28 of A301. If it is missing, check the logic probe readings on pins 1 to 40 of ANTIC (A302) and check A302 by substitution.
  4. If the waveform at pin 21 is good, check the voltages, waveforms and parts around the colour transistor Q107.
  5. If the colours are present but wrong, check the setting of R309 and the frequency of the oscillator at pin 28 of A301. Sams gives the crystal frequency as 3.579575 MHz, measured with a frequency counter at the collector of Q104.

Atari's colour bar chart, with SALT II showing colour bars (press C and RETURN):[1]

  1. If the bars do not look like Atari's figure 3-4, try to set them with R309. If R309 will not give the right colour, swap A301 and A302 on the CPU board, then the whole CPU board.
  2. If a new CPU board cures it, trace the colour circuitry on the old CPU board, including the colour delay circuit and R309.
  3. If not, swap A111 and Q107 on the motherboard.
  4. If the fault remains, lock SALT II into continuous colour bars and check each point in turn against Atari's waveform photographs: 3.58 MHz oscillation at R158 on the motherboard (if it is missing, swap X101, Q103 and Q104), the input signal at the base of Q107, the output from the collector of Q107, and the signal at J107 pin 1. Where a signal is missing, trace the circuit back to the previous step.
  5. Then check for +5 V on modulator pin 5 and for the signal on modulator pins 4 and 2.

Atari's grey bar chart uses the same swaps and the same checkpoints.[1]

Adjust

[edit | edit source]
  1. Turn on the computer and adjust the colour control R309 for a blue screen.[2]
  2. Set a television to channel 2 or 3 with its AFC off, set the channel switch S201 to the same channel, and adjust L210 for the best picture.[2]

Reassemble

[edit | edit source]
  1. Refit the shields, the power supply board, the keyboard and the cabinet as in Atari 400 Power Supply Repair. Route the RF cable through its slot so it is not trapped under the module assembly.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge: the words ATARI COMPUTER - MEMO PAD should appear in the upper left corner of the screen.[1]
  2. With SALT II, run the colour bar and grey bar tests and compare the screen with Atari's figures 3-4 and 3-6.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 400 motherboard schematic (figure 2-2B, p. 2-5: J110, A111, R171-R180, Q107, C185-C187, J107), 400 power supply schematic (figure 2-4, p. 2-8: J201, J203, A203, S201), testing with SALT II (pp. 3-2 and 3-9), 400 disassembly (pp. 4-1 to 4-6), 400 colour bar troubleshooting (pp. 5-9 to 5-12), 400 grey bar troubleshooting (pp. 5-14 to 5-17), symptom checklist (section 6), 400 parts list (section 9: A111 C010816, X101 C010177, Q103-104 2N3906, Q107 2N3904, R176 and R177, RF module "B" CA012174). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 Howard W. Sams & Co., Computerfacts CC5, Atari Model 400, 1984: preliminary service checks ("RF Modulator Check"), test equipment, disassembly instructions, troubleshooting guide ("Sync", "Crystal Oscillator", "Color", "Video"), and adjustments, p. 7 ("RF Modulator Adjustment", "Color Adjustment", alignment tools). Scan on the Internet Archive.