Jump to content

Atari 400 Sound Repair

From RetroTechCollection
Atari 400 audio circuit, sound oscillator Q105 and mixer Q106 (Field Service Manual figure 2-2B)
Atari's schematic of the 400 sound circuit: POKEY's audio line with its 1 kΩ pull-up R160 enters at the left through C164 and R161; Q105 with L101 and L102 is the 4.5 MHz sound oscillator; Q106 is the audio mixer; R170, C184 and the bead L118 lead to the modulator line

The Atari 400 makes sound in two places. The television sound comes from POKEY (A101): its audio output, pin 37, feeds a 4.5 MHz sound oscillator built round Q105 and an audio mixer built round Q106 on the motherboard, and the result goes to the RF modulator (A203) on the power supply board.[1][2] The keyboard click and the console beeps come from the small speaker in the console, SP101, driven by Q101 from pin 15 of the CTIA or GTIA (A301) on the CPU board.[2] Atari's 400 tone test and Sams' service data both work along these paths and give the parts to check at each stage.[1][2]

Symptoms

[edit | edit source]
  • No sound from the television, while the picture is good.[2]
  • Sound from a BASIC SOUND statement, but wrong or missing sounds in other programs: Sams points at POKEY.[2]
  • No click from the console speaker when a key is pressed.[2]
  • No sound from a peripheral's audio, for example the voice track of a cassette: the external audio input.[2]

Check the television first: Atari's chart ends by setting the RF modulator to channel 3 with the television tuned to channel 3, the fine tuning set for a clear picture and the volume turned up.[1] A snowy picture as well as no sound is an RF or supply fault; see Atari 400 Power Supply Repair and Atari 400 Video Output Repair.

Safety

[edit | edit source]

The external adaptor plugs into the mains; the console itself runs from 9 V AC and the rails made from it.[1] Unplug the adaptor before removing or fitting a chip or the speaker. Use static precautions with the boards.[1]

Tools and parts

[edit | edit source]
  • An oscilloscope and a frequency counter; Sams also uses a logic probe and a digital meter.[2]
  • Optional: Atari's SALT II cartridge, whose tone test (T) the flowchart uses. Best Electronics sells SALT 2.05 (TE15644).[1][3]
  • Parts as found, from Atari's 400 parts list:[1]
Atari 400 sound parts (Atari parts list and schematic)
Position Part Atari number
A101 POKEY C012294
Q105 2N3563 transistor (sound oscillator) 34-2N3563
Q106 2N3906 transistor (audio mixer) 33-2N3906
L101 Variable inductor, 0.6–1.2 µH C010823
L102 Inductor, 2 µH C010822
C177, C178 820 pF C010821
R160 1 kΩ 14-5102
R161 18 kΩ 14-5183
R166 6.8 kΩ 14-5682
R170 4.7 kΩ 14-5472
C164, C179 0.1 µF ceramic C014181-03
C184 0.001 µF ceramic C014181-01
Q101 MPS06 transistor (speaker driver) C014394
CR101 1N914 diode 31-1N914
SP101 Speaker assembly, 63 Ω CA011840
A203 RF module "B" (power supply board) CA012174

Procedure

[edit | edit source]

Open the machine

[edit | edit source]
Atari 400 motherboard and power supply board (Knurrikowski)
An Atari 400 motherboard (left) and power supply board (right). POKEY (A101) is in the centre of the motherboard; the RF modulator can is on the power supply board. Photo: Knurrikowski, CC BY-SA 4.0.
  1. Remove the four screws from the bottom, open the cartridge door and remove the top cabinet. Unplug the RF modulator cable and remove the bottom of the cabinet.[2]
  2. Remove the single keyboard screw, lift the left end of the keyboard and unplug its ribbon cable. Remove the two power supply screws, lift out the interlock switch plunger and lift the power supply board straight up off the motherboard pins.[1][2] The full sequence, with the keyboard, is in Atari 400 Power Supply Repair.
  3. Remove the eight screws from the bottom shield and lift the shield off. POKEY (A101) is in a 40-pin socket on the motherboard; the CTIA or GTIA (A301) is on the CPU board.[2][1]

No sound from the television

[edit | edit source]

Sams' sequence, with the computer running:[2]

  1. Type in and run 10 SOUND 0,100,10,15: GOTO 10.
  2. Check pin 37 of POKEY (A101) for the waveform shown in Sams' figure 1. If it is missing, check A101 by substitution.
  3. If the waveform is correct, check the sound oscillator Q105 with the frequency counter: it should run at 4.5 MHz. If it does not, check the voltages and parts around Q105.
  4. If Q105 is working, check R161 and R164 and the capacitors C164 and C183.

Atari's tone test with SALT II goes further:[1]

  1. Press T and RETURN, enter the voice number (1 to 4) and press RETURN. Listen for all eight tones or speaker clicks. The first two tones are very high and may be inaudible; the clicks from the DC level shifts can be heard for each tone.
  2. If the tones are missing, replace POKEY (A101) and test again.
  3. If they are still missing, lock SALT II into continuous mode, restart the test on voice 1 and put the scope on pin 37 (AUD) of A101. Each tone should show as a frequency that falls while its amplitude decays to 0 V.
  4. If it does not, or if the later steps of the test fail, check the parts on the audio line in this order: R160 (1 kΩ) for a short; C164 (0.1 µF), C179 (0.1 µF), R161 (18 kΩ) and R166 (6.8 kΩ) for an open circuit; C184 (0.001 µF) and R170 (4.7 kΩ) for a short or an open circuit.
  5. Check that the oscillator runs at 4.5 MHz with the scope on the emitter of Q105: Atari's figure for 4.5 MHz is a sine wave about 2.3 cm long per cycle at 0.1 µs/div and 20 mV/div, and L101 must be adjustable to 4.5 MHz. If it is not, repair the oscillator and test again.
  6. If the oscillator is good, check the input to the audio mixer at the collector of Q106 (0.5 ms/div, 5 mV/div). The waveform should match POKEY pin 37, rounded instead of square.
  7. Check for output on L118 (0.5 ms/div, 50 mV/div). If there is none, replace Q106 and test again.
  8. If there is output on L118, adjust the RF modulator A203 to channel 3, tune the television to channel 3 with the fine tuning set for a clear picture, turn the volume up and test again. Run the test for the other three voices.

Set the sound oscillator

[edit | edit source]

Sams' sound adjustment: connect a pickup loop to the input of a frequency counter, slip the loop over L101 and adjust L101 for 4.5 MHz. Sams lists GC Electronics alignment tools 9300, 9302 and 9304 for L101.[2]

No click from the console speaker

[edit | edit source]

Sams' sequence:[2]

  1. Check the speaker SP101. It plugs into the motherboard on J106; the plug has no polarity.[2][1]
  2. If the speaker is good, type in and run 10 PRINT CHR$(253): GOTO 10.
  3. Check for pulses of about 0.7 V peak to peak at pin 15 of the CTIA or GTIA (A301). If they are missing, check A301 by substitution.
  4. If they are present, check for pulses of about 0.5 V peak to peak at the base of Q101. If those are missing, check the connection at pin S of J110 (the CPU board connector), R123, C121 and Q101.
  5. If the pulses reach the base of Q101, check Q101, the diode CR101, R118 and the 5.08 V supply.

Atari's console switch test uses the same speaker: if the speaker does not beep when a console key is pressed, the chart checks R119 to R122 and C121 to C124 for shorts or opens.[1]

External audio input dead

[edit | edit source]
  1. The audio input comes in on pin 11 of the peripheral socket J202, on the power supply board, and reaches the motherboard on J201 pin 10.[1]
  2. Check the connections at J202 pin 11 and J201 pin 10, then the voltages and parts around the audio mixer Q106.[2]

Reassemble

[edit | edit source]
  1. Refit the shield with its eight screws, then the power supply board, the interlock plunger and the cabinet, as in Atari 400 Power Supply Repair. Route the RF cable through its slot so it is not trapped under the module assembly.[1]

Testing

[edit | edit source]
  1. Run 10 SOUND 0,100,10,15: GOTO 10 and listen to the television.[2]
  2. Type at the keyboard and listen for the click from the console speaker.[2]
  3. With SALT II, run the tone test on all four voices.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 400 motherboard schematic (figure 2-2B, p. 2-5: R160-R170, C164, C177-C184, Q105, Q106, L101, L102, L118), 400 power supply schematic (figure 2-4, p. 2-8: J201, J202, A203), disassembly and assembly notes (pp. 4-1 to 4-6 and 4-15 to 4-17), 400 tone test (pp. 5-24 to 5-27), 400 console switch test (p. 5-28), 400 parts list (section 9: A101 C012294, L101 C010823, L102 C010822, C177-178 C010821, Q101 MPS06 C014394, speaker assembly 63 Ω CA011840, RF module "B" CA012174, Q105 2N3563, Q106 2N3906). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 Howard W. Sams & Co., Computerfacts CC5, Atari Model 400, 1984: test equipment, disassembly instructions, troubleshooting guide, "Audio", and adjustments, "Sound Adjustment" (p. 7). Scan on the Internet Archive.
  3. ↑ Best Electronics, "Atari 400 / 800 Computers" parts page: SALT 2.05 diagnostic cartridge TE15644. Retailer listing.