Atari 400 Keyboard Repair

The Atari 400 has a flat membrane keyboard that plugs into the 22-pin connector J105 on the motherboard.[1] POKEY (A101) scans it through two CD4051 analogue multiplexers: Z102 ("key out") drives the eight row lines and Z101 ("key in") reads the column lines back to POKEY. BREAK, CONTROL and the two SHIFT keys sit on a column of their own that goes straight to POKEY pin 16. START, SELECT, OPTION and SYSTEM RESET leave J105 on pins 18 to 21 and run through the CPU board connector J110 to the CTIA or GTIA and ANTIC on the CPU board.[1][2] A keyboard fault is in the membrane, in its tail and J105, or in POKEY and the two multiplexers. Atari's flowchart and Sams' service data separate them, and all three chips are in sockets.[1][2]
Atari's parts list gives the keyboard assembly as CA014031, replaced by CA017999.[1] Len Spencer, writing for an Atari user group in 1991, called the 400's membrane keyboard "a joke from the git-go" and gave replacement as the only cure for a failed one.[3]
Symptoms
[edit | edit source]- Some keys do nothing while others work. Atari's chart points at the keyboard.[1]
- No key works at all, although the ATARI COMPUTER - MEMO PAD screen appears. Atari's chart points at POKEY and the multiplexers.[1]
- A row or column of keys is dead: the keys share one J105 pin (see the chart below).[1]
- SHIFT, CONTROL or BREAK do not work: the column on J105 pin 9 and POKEY pin 16.[1][2]
- START, SELECT, OPTION or SYSTEM RESET do not work.[2]
- No click from the console speaker when a key is pressed. That is an audio fault in the keyclick circuit; see Atari 400 Sound Repair.[2]
Atari's first check needs no tools: with no cartridge fitted, switch on, press every key at the Memo Pad and watch for each one on the screen, including CONTROL with other keys. Atari says that one failed key is probably the keyboard and that more than one needs the further tests below.[1] A blank or coloured screen with no Memo Pad is a different fault; see Atari 400 Black Screen Repair and the Atari 400 Troubleshooting Guide.
Safety
[edit | edit source]Unplug the power adaptor before opening the case or unplugging the keyboard. Atari's manual warns that plastic and aluminium parts strip easily: use the right screw in each hole, and do not exceed 6 inch-pounds on plastic or 10 inch-pounds on aluminium. Use static precautions when handling the boards.[1]
Tools and parts
[edit | edit source]- A cross-head screwdriver, a logic probe and an oscilloscope.[2]
- Optional: Atari's SALT II diagnostic cartridge, whose keyboard test the flowchart uses. Best Electronics sells the SALT 2.05 cartridge (TE15644).[1][4]
- A replacement keyboard. Best Electronics sells the 400 keyboard as the "Mono Panel Keyboard", CA017999.[4]
- Spare chips for swapping: CD4051B (Atari C014336) for Z101 and Z102, and POKEY (C012294) for A101.[1]
Procedure
[edit | edit source]Remove the keyboard
[edit | edit source]
- Turn the unit upside down and remove the four screws from the bottom cover.[1]
- Turn the unit upright, unhook the top cover from the keyboard, open the cartridge door and lift the top cover off.[1]
- Remove the single keyboard screw.[1]
- Lift the left end of the keyboard and disconnect the keyboard ribbon cable.[1]
Find which line has failed
[edit | edit source]
- List the keys that fail at the Memo Pad, or in the SALT keyboard test (press K and RETURN; failed keys show in red).[1]
- Look them up in the table. Keys that share a J105 pin and all fail point at that line: its track in the membrane or tail, its contact in J105, or its multiplexer pin.[1]
- Scattered single keys that share no line point at the membrane itself. Atari's chart says to replace the keyboard when only some keys fail.[1]
| J105 pin | Line goes to | Keys |
|---|---|---|
| 1 | Z102 pin 14 | BREAK, 7, 8, 9, 0, CLEAR, INSERT, DELETE |
| 2 | Z102 pin 1 | ESC, 1, 2, 3, 4, 5, 6 |
| 3 | Z102 pin 2 | U, I, O, P, −, =, RETURN |
| 4 | Z102 pin 15 | TAB, Q, W, E, R, T, Y |
| 5 | Z102 pin 4 | CONTROL, J, K, L, semicolon, +, * |
| 6 | Z102 pin 13 | CAPS/LOWR, A, S, D, F, G, H |
| 7 | Z102 pin 12 | N, M, comma, full stop, /, Atari key, SPACE BAR |
| 8 | Z102 pin 5 | Both SHIFT keys, Z, X, C, V, B |
| 9 | POKEY (A101) pin 16 | BREAK, CONTROL, both SHIFT keys |
| 10 | Z101 pin 1 | 6, 7, Y, U, N |
| 11 | Z101 pin 2 | H, J, SPACE BAR |
| 12 | Z101 pin 15 | 5, 8, T, I, G, K, B, M |
| 13 | Z101 pin 4 | 4, 9, R, O, F, L, V, comma |
| 14 | Z101 pin 5 | 3, 0, E, P, D, semicolon, C, full stop |
| 15 | Z101 pin 14 | 2, CLEAR, W, −, S, +, X, / |
| 16 | Z101 pin 13 | 1, INSERT, Q, =, A, *, Z, Atari key |
| 17 | Z101 pin 12 | ESC, DELETE, TAB, RETURN, CAPS/LOWR |
Whole keyboard dead
[edit | edit source]
To reach the chips, remove the power supply board and the module assembly as described in Atari 400 Power Supply Repair, then:[1]
- Disconnect and remove the speaker assembly and lift the module assembly out of the bottom cover.
- Close and latch the cartridge door, set the module on its back, remove the eight screws from the bottom shield and lift the shield off.
- Lift the motherboard assembly out of the aluminium casting. POKEY (A101), Z101 and Z102 are in sockets on the motherboard.
Then follow Sams' checks, with the keyboard reconnected and the power on:[2]
- Check for waveforms on pins 18 to 23 of POKEY (A101), the keyboard scan lines. If they are missing, check A101 by substitution.
- If they are present, check the waveforms on POKEY pins 16 and 25 while pressing keys, and check pin 29 with a logic probe for a pulse each time a key is pressed. Pin 16 shows a waveform when BREAK, CONTROL or SHIFT is pressed. Pin 25 shows one for every other key except SYSTEM RESET, OPTION, SELECT and START. Pin 29 pulses for every key except SHIFT, CONTROL, SYSTEM RESET, OPTION, SELECT and START.
- If the waveform at pin 16 or 25 is missing, check the voltages and logic probe readings on pins 1 to 16 of Z101 and Z102 against Sams' logic chart. If they are wrong, check the chip by substitution. If they are right, check J105 and the keyboard contacts.
- If pins 16 and 25 are good but pin 29 does not pulse when a key is pressed, check A101 by substitution.
Atari's own chart for all keys failing says to swap A101, Z103 and Z104, and shows typical waveforms at Z104 pins 14 and 3 with the W key held down.[1] Those are the 800's designators. On the 400, Z103 is the 74LS42 memory map decoder and Z104 a 74LS10; the keyboard connection chart pairs the 800's Z103 and Z104 with the 400's Z102 and Z101.[1] On a 400, swap A101, Z101 and Z102, and look for the waveforms at Z101 pin 14 (W lies on that column) and pin 3. Len Spencer's advice was the same: swap the two 4051s one at a time.[3]
START, SELECT, OPTION or SYSTEM RESET dead
[edit | edit source]- Put the logic probe on pins 12, 13 and 14 of the CTIA or GTIA (A301) and on pin 6 of ANTIC (A302), both on the CPU board, and press each key in turn. Each line should go low while its key is pressed.[2]
- If a line does not go low, check the pin connections of J110 and J105 and the keyboard contacts for that key.[2]
- If the lines go low correctly but the keys still do nothing, check A301 and A302 by substitution.[2]
- Atari's console switch test (press S and RETURN on SALT, then each of the four keys) checks R119 to R122 and C121 to C124 for shorts or opens when the console speaker does not beep as a key is pressed, and replaces A301 when it does.[1] On the schematic these lines run from J105 pins 18 to 21 through the group of 150 Ω resistors R119 to R123, with .001 µF capacitors (C121 to C125) to ground.[1]
Replace the keyboard
[edit | edit source]- Plug the new keyboard's ribbon cable into the connector on the motherboard.[1]
- Gently lower the keyboard over the power-on LED and the guide posts on the aluminium casting.[1]
- Insert and tighten the single keyboard screw.[1]
Reassemble
[edit | edit source]- If the module was removed, refit it, the speaker, the keyboard and the power supply board in the order given in Atari 400 Power Supply Repair. Atari's notes: the CPU board must sit in its guides in the casting, the bottom shield takes eight screws, and the speaker plug has no polarity.[1]
- Open the cartridge door and slide the top cover down over it and the power-on LED.[1]
- Guide the top cover's locator pins into the keyboard holes and snap the top cover's hood under the keyboard.[1]
- Close the cartridge door, set the console on its face and refit the four bottom screws.[1]
Testing
[edit | edit source]- Switch on with no cartridge and press every key at the Memo Pad, including CONTROL with other keys; each should appear on the screen.[1]
- With SALT II, run the keyboard test (K and RETURN): press every key except SPACE BAR, CONTROL and the SHIFT keys, then CONTROL with A, each SHIFT key with A, SPACE BAR and RETURN. The screen shows KEYBOARD PASS or KEYBOARD FAIL.[1]
- Run the switch test (S and RETURN) and press START, SELECT, OPTION and SYSTEM RESET in that order.[1]
Related pages
[edit | edit source]- Atari 400
- Atari 400 Troubleshooting Guide
- Atari 400 Sound Repair
- Atari 400 Power Supply Repair
- Atari 800 Keyboard Repair
- Keyboard Membrane Trace Repair
- IC Removal and Socketing
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: keyboard key-in and key-out multiplexers Z101 and Z102 and memory map decoder Z103 (p. 1-12), 400 motherboard schematic (figure 2-2A, p. 2-4: J105, Z101, Z102, A101, R119-R123, C121-C125), power-up and keyboard tests (p. 3-2), SALT keyboard and switch tests (p. 3-9), 400 disassembly and assembly (pp. 4-1 to 4-6 and 4-15 to 4-17), 400 keyboard flowchart (pp. 5-22 and 5-23), 400 console switch test (p. 5-28), keyboard connection chart (p. 5-38), 400 parts list (section 9: keyboard CA014031 and CA017999, Z101-102 C014336, Z103 74LS42, Z104 74LS10, A101 C012294, sockets). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 Howard W. Sams & Co., Computerfacts CC5, Atari Model 400, 1984: troubleshooting guide, "Keyboard" and "Audio". Scan on the Internet Archive.
- ↑ 3.0 3.1 Len Spencer, "The Workbench" (reprinted from the Mid-Florida Atari Computer Club Bulletin), Z*Magazine issue 192, 24 April 1991. Text at textfiles.com. Community article.
- ↑ 4.0 4.1 Best Electronics, "Atari 400 / 800 Computers" parts page: 400 "Mono Panel Keyboard" CA017999 and SALT 2.05 diagnostic cartridge TE15644. Retailer listing.