Jump to content

Atari 800 Video Output Repair

From RetroTechCollection
Atari 800 video buffers A103, video amplifier Q105 and colour circuit A104 (Field Service Manual figure 2-6B)
Atari's schematic of the 800 video circuit: the luminance and sync lines from the CPU board connector J101 (left) pass through the CD4050 buffers A103B to A103F and the summing resistors into the video amplifier Q105; the colour line goes through A104A and A104B; the four outputs leave through L103 to L105 to J115 (right)

The Atari 800 has two video outputs: the RF socket for a television and the 5-pin monitor socket J205, which carries separate composite video, luminance and chroma signals and audio.[1] The CTIA or GTIA (A301) and ANTIC (A302) on the CPU board make the picture. Four luminance lines, the composite sync and the colour signal come through the CPU board connector J101 to the motherboard, where the CD4050 buffer A103 and a resistor ladder sum the luminance and sync into the video amplifier Q105, and two sections of the transistor array A104 handle the colour. The signals leave the motherboard on J115 and reach the power supply board on J201, which carries the RF modulator and the monitor socket.[1][2] Atari's colour bar and grey bar charts and Sams' service data follow this path stage by stage.[1][2]

Symptoms

[edit | edit source]
  • No picture on the television, while the monitor socket works, or no picture on either.[2]
  • A picture with no colour, or wrong colours.[2]
  • A picture that rolls or tears: no vertical or horizontal sync.[2]
  • A snowy screen: Atari's checklist gives the switch box, the AC adaptor, the channel select switch, the modulator adjustment and RF cable damage; see also Atari 800 Power Supply Repair.[1]
  • Missing or wrong bars in the SALT II colour bar or grey bar test.[1]

Try the monitor socket before opening the case: it does not go through the RF modulator. A black, green, yellow or blue screen at switch-on with no Memo Pad is a power-up fault; see Atari 800 Black Screen Repair and the Atari 800 Troubleshooting Guide.

Safety

[edit | edit source]

The adaptor plugs into the mains; unplug it before removing a board. If a CRT television or monitor is opened during fault-finding, follow CRT Discharge Procedure.

Tools and parts

[edit | edit source]
  • An oscilloscope, a frequency counter, a logic probe and a meter.[2]
  • A monitor with composite input and a 5-pin DIN cable, and a television tuned to channel 2 or 3.
  • An alignment tool for the modulator coil; Sams lists GC Electronics 9300, 9302 and 9304.[2]
  • Optional: SALT II, whose colour bar (C) and grey bar (G) tests the charts use.[1]
  • Parts as found: CD4050 for A103 (Atari C010816), the transistor array A104 (C010174), 2N3904 for Q105, 2N3906 for Q102 and Q103, the crystal X101 (C010177) and the RF module "B" (CA012174).[1]

The monitor socket and the video path

[edit | edit source]
Atari 800 right-hand side panel (Evan-Amos)
The 800's side panel: the monitor socket J205 is at the left, beside the peripheral socket. Photo: Evan-Amos, public domain.
Atari 800 monitor socket J205 (Atari figure 2-8)
J205 pin Signal J201 pin
1 Composite luminance 5
2 Ground –
3 Audio out 2
4 Composite video 6
5 Composite chroma 3

[1]

Luminance and sync into the video amplifier Q105 (Atari figure 2-6B)
Signal from the CPU board A103 input A103 output Summing part
LM0 9 10 R181, 18 kΩ
LM1 14 15 R182, 9.1 kΩ
LM2 11 12 R183, 4.7 kΩ
LM3 5 4 R180, 36 kΩ
Video sync 7 6 Diode CR108
Colour – – R196 (3.3 kΩ) and 10 pF into A104A and A104B

[1]

The motherboard sends four signals to the power supply board through J115: composite luminance (pin 5), the modulator signal (pin 20), composite video (pin 6) and composite chroma (pin 3), through the ferrite beads L103 to L105.[1]

Procedure

[edit | edit source]

Check the connection first

[edit | edit source]

Sams' RF modulator check:[2]

  1. Switch on and check that both power LEDs (CR210 and CR211) light; if not, see Atari 800 Power Supply Repair.
  2. Check that the channel select switch S203 is on the same channel as the television, 2 or 3.
  3. Check that the TV/computer switch in the switch box is set to computer, and check the connections and hook-up at both ends.
  4. If there is still no picture, check the voltages at the RF modulator's connections; if they are correct, substitute the modulator.

Open the machine

[edit | edit source]
  1. Remove the bottom cover (five screws), the two casting flange screws and the power supply board's lower left screw, disconnect the speaker, swing the top cover up, unplug the keyboard cable and set the top cover aside.[1]
  2. Unplug the RF cable and the power supply harness, remove the three power supply board screws and lift the board straight up.[1]
  3. Turn the unit upside down, remove the nine screws from the lower shield and lift the motherboard and shield out of the casting. The CPU board plugs into the motherboard and can then be removed.[1]

No picture

[edit | edit source]

Sams' sequence:[2]

  1. Check for a video waveform at pin 20 of J201. If it is correct, check the RF modulator.
  2. If it is missing, check the waveforms and voltages on pins 9 to 12, 14 and 15 of A103. If any waveform is missing, check A103 by substitution.
  3. Check the voltages, waveforms and logic probe readings on pins 1 to 40 of the CTIA (A301); if any are wrong, check A301 by substitution.

No sync

[edit | edit source]
  1. Check the waveform at pin 25 of the CTIA (A301). If it is missing, check A301 by substitution.[2]
  2. If it is correct, check the voltages and waveforms on pins 6 and 7 of A103, the sync buffer.[2]

No colour or wrong colour

[edit | edit source]
Atari 800 colour bar troubleshooting with scope waveforms (Field Service Manual page 7-11)
Atari's 800 colour bar troubleshooting chart, with the expected scope waveform beside each check: 3.58 MHz at R106, the input to Q105's base, the output from its emitter and the signal at J115 pin 20

Sams' sequence:[2]

  1. Check the colour waveform at pin 21 of the CTIA (A301).
  2. If it is missing, check the colour control R309 on the CPU board: the voltage at pin 17 of A301 should vary from about 0 V to 7 V as R309 is turned from maximum to minimum. If it does not change, check R309, C305, R308, the 11.8 V supply and A301 by substitution.
  3. If R309 is working, check the waveform at pin 28 of A301. If it is missing, check the logic probe readings on pins 1 to 40 of ANTIC (A302) and substitute A302 if they are wrong.
  4. If the waveform at pin 21 is correct, check the voltages, waveforms and parts around pins 10, 12 and 14 of A104, and the waveform at pin 3 of J201 on the power supply board.
  5. If the colours are wrong, check the setting of R309 and the frequency of the 3.57957 MHz oscillator at pin 28 of A301. Sams' colour oscillator check is 3.57957 MHz at the collector of Q102; if it is wrong, substitute the crystal X101.

Atari's colour bar chart, with SALT II showing colour bars (C and RETURN):[1]

  1. If the bars do not look like Atari's figure 3-4, swap A301 and A302 on the CPU board, then the whole CPU board. If a new CPU board cures it, trace the colour circuitry on the old one, including the colour delay circuit and R309.
  2. If not, swap A103, Q105 and A104 on the motherboard.
  3. If the fault remains, lock SALT II into continuous colour bars and check each point against Atari's waveform photographs: 3.58 MHz at R106 on the motherboard (if it is missing, swap X101, Q102 and Q103), the input signal at the base of Q105, the output from Q105's emitter, and the signal at J115 pin 20. Where a signal is missing, trace the circuit back to the previous step.

Atari's grey bar chart (G and RETURN) uses the same swaps and checkpoints.[1]

Adjust

[edit | edit source]
Atari 800 CPU board (Evan-Amos)
An Atari 800 CPU board with the colour adjustment trimmer at the right. Photo: Evan-Amos, public domain.
  1. Turn on the computer and adjust the colour control R309 for a blue screen on the monitor.[2]
  2. Set a television to channel 2 or 3 with its AFC off, set the channel switch S203 to the same channel and adjust the modulator coil L210 for the best picture.[2]

Reassemble

[edit | edit source]

Refit the motherboard and lower shield (nine screws), the power supply board, the module and the covers as in Atari 800 Power Supply Repair. Plug the power supply harness on with the orange or purple wire towards the casting, and keep the RF cable from being trapped between the power supply board and the top cover standoff.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge: ATARI COMPUTER - MEMO PAD should appear on both the television and the monitor.[1]
  2. Check each signal at J205 with the scope against the table above.[1]
  3. With SALT II, run the colour bar and grey bar tests and compare the screen with Atari's figures 3-4 and 3-6.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 800 motherboard schematic (figure 2-6B, p. 2-11: J101, A103, R179-R183, CR108, Q105, A104, R196-R206, L103-L105, J115, X101, Q102, Q103, R106), 800 power supply schematic (figure 2-8, p. 2-13: J201, J205, A203, S203), testing with SALT II (pp. 3-2 and 3-9), 800 disassembly and assembly (pp. 4-9 to 4-12 and 4-17 to 4-19), 800 colour bar and grey bar troubleshooting (pp. 7-9 to 7-17), symptom checklist (section 6), 800 parts list (section 9: A103 C010816, A104 C010174, Q105 2N3904, Q102-103 2N3906, X101 C010177, RF module "B" CA012174). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: preliminary service checks ("RF Modulator"), test equipment, troubleshooting ("Video", "Sync", "Color Oscillator", "Color"), and miscellaneous adjustments ("Color Adjustment", "RF Modulator Adjustment", alignment tools). Scan on the Internet Archive.