Jump to content

Atari 400 Operating System ROM Replacement

From RetroTechCollection
Atari 400 motherboard silkscreen with OS ROMs A103 and A104 circled (Tech Tip 2)
The first enclosure to Atari's Tech Tip 2 (May 1982): the 400 motherboard silkscreen with the operating system ROM positions A103 and A104 circled, printed sideways as in the original

The operating system of the Atari 400 is held in three ROMs in 24-pin sockets on the motherboard: ROM F at A103 and ROM E at A104, both 4K parts, and the 2K ROM D at A105.[1] Atari revised the F and E ROMs in 1982. Its Tech Tip 2 says that new 400 and 800 computers contain Revision B ROMs, that Revision A and Revision B must not be mixed because the system will not operate with one of each, and that the ROMs should be replaced if they are defective or if a printer overprints ("hiccups").[2] A failed ROM shows as a green or yellow screen at switch-on, as a checksum failure in Atari's SALT II verify ROM test, or, for ROM D, as a computer that starts but will not run a cartridge.[1][3]

Atari 400 operating system ROMs (Atari parts list and Tech Tip 2)
Position ROM Size Atari number
A103 F 4K C014599 (Revision A: C014599A; Revision B: C014599B)
A104 E 4K C012499 (Revision A: C012499A; Revision B: C012499B)
A105 D 2K C012399

[1][2]

Symptoms

[edit | edit source]
  • A green or yellow screen at switch-on with no Memo Pad. Atari's chart checks the RAM card first, starting with the lowest RAM slot, then swaps ROMs F (A103), E (A104) and D (A105), then A303, Z303 and Z304 on the CPU board.[1]
  • The computer does not come up although the supply and the crystal are good: Sams lists ROMs A103 and A104 among the parts to substitute, with A111, Z103 and Z104.[3]
  • The computer comes up but a cartridge does not work: Sams says to substitute ROM A105.[3]
  • A printer overprints: Atari's Tech Tip 2 says to replace the ROMs.[2]
  • SALT II's verify ROM test reports FAIL for one or more ROMs.[1]

A black, grey or blue screen has other causes; see Atari 400 Black Screen Repair and the Atari 400 Troubleshooting Guide. RAM faults are in Atari 800 RAM Replacement#On the 400.

Safety

[edit | edit source]

Switch the computer off before removing or fitting any chip or board.[2] Use static precautions when handling the boards, and do not overtighten the screws in the plastic and aluminium parts.[1]

Tools and parts

[edit | edit source]
  • A cross-head screwdriver and a 24-pin IC insertion tool; Sams lists insertion tools for 14, 16, 24 and 40-pin chips.[3]
  • Replacement ROMs: a matched pair of the same revision for A103 and A104, and C012399 for A105.[2][1]
  • Optional: SALT II, whose verify ROM test (V) checks each ROM's checksum.[1]

Procedure

[edit | edit source]

Identify the revision

[edit | edit source]
  1. Read the top of each ROM. Atari's Tech Tip 2 says a Revision B part is printed with a copyright symbol followed by "1981 Atari".[2]
  2. Check that A103 and A104 are the same revision. A Revision A ROM paired with a Revision B ROM will not run.[2]

Find the failing ROM

[edit | edit source]

With SALT II fitted:[1]

  1. Press V and RETURN to run the verify ROM test. The screen shows a checksum for each ROM and for the maths pack, with PASS or FAIL for each, and then PASS or FAIL for the whole test. Atari suggests running it for 15 or 20 minutes if a ROM is suspected of failing intermittently.
  2. If it fails, lock the test into continuous mode (press D, E, C and V, each followed by RETURN) and note which ROM fails.
  3. Atari's 400 verify ROM chart gives the replacement as A402 for ROM D, A403 for ROM E and A401 for ROM F, and all three if every ROM fails. Those are the 800's ROM module positions; on the 400 the same ROMs are D at A105, E at A104 and F at A103.[1]
  4. If no single ROM accounts for the failure, the chart swaps Z401 to Z403 and checks φ2 on the 800's ROM module, which the 400 does not have. On the 400 schematic the ROMs' chip-select lines come from the 74LS42 memory map decoder Z103; Atari's black screen chart lists Z103 to Z105, and Sams lists Z103 and Z104, for substitution.[1][3]

Without SALT II, follow Atari's green or yellow screen chart: rule out the RAM card, then swap the three ROMs for known-good parts one at a time.[1]

Reach the motherboard

[edit | edit source]
Atari 400 motherboard and power supply board (Knurrikowski)
An Atari 400 motherboard (left) and power supply board (right). The operating system ROMs are the three 24-pin chips at the left of the motherboard, above the PIA. Photo: Knurrikowski, CC BY-SA 4.0.
  1. Turn the unit upside down and remove the four screws from the bottom cover. Turn it upright, unhook the top cover from the keyboard, open the cartridge door and lift the top cover off.[1]
  2. Remove the single keyboard screw, lift the left end of the keyboard and disconnect its ribbon cable.[1]
  3. Disconnect the RF cable, remove the two power supply screws, pull the power supply about a quarter of an inch from the casting, lift out the interlock switch plunger and lift the power supply straight up off the motherboard pins.[1]
  4. Disconnect and remove the speaker assembly and lift the module assembly out of the bottom cover.[1]
  5. Close and latch the cartridge door, set the module on its back, remove the eight screws from the bottom shield and lift the shield off.[1]
  6. Lift the motherboard assembly out of the aluminium casting.[1]

Replace the ROMs

[edit | edit source]
  1. Remove the ROM at A103, A104 or A105 from its socket, noting the orientation of its notch. See IC Removal and Socketing.
  2. Fit the replacement in the same orientation. When updating to Revision B, replace C014599A at A103 and C012499A at A104 with C014599B and C012499B, as a pair.[2]
  3. Inspect the socket contacts while the chip is out.

Reassemble

[edit | edit source]
  1. Set the aluminium casting upside down, invert the motherboard and lower it in, with the CPU board in its guides in the casting. Fit the lower shield with its eight screws and put the module assembly in the bottom cover.[1]
  2. Plug in the speaker cable (it has no polarity), plug in the keyboard ribbon cable and lower the keyboard over the power-on LED and guide posts.[1]
  3. Refit the power supply, the interlock plunger, the two power supply screws, the RF cable and the keyboard screw, then the top cover and the four bottom screws, as in Atari 400 Power Supply Repair.[1]

Testing

[edit | edit source]
  1. Switch on with no cartridge: ATARI COMPUTER - MEMO PAD should appear.[1]
  2. Atari's Tech Tip 2 tests with the Stand Alone Test diagnostic (SALT); run the verify ROM test and check that every ROM passes.[2][1]
  3. Fit a cartridge, such as BASIC, and check that it runs; Sams ties a cartridge that will not work to ROM A105.[3]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: memory map decoder Z103 (p. 1-12), 400 motherboard schematic (figure 2-2A, p. 2-4: ROMs A103-A105, Z103), power-up and verify ROM tests (pp. 3-2 and 3-11), 400 disassembly and assembly (pp. 4-1 to 4-6 and 4-15 to 4-17), 400 black/grey screen and green/yellow screen charts (pp. 5-5 and 5-6), 400 verify ROM chart (pp. 5-29 and 5-30), 400 parts list (section 9: A103 C014599, A104 C012499, A105 C012399, 24-pin sockets for A103-A105, Z103 74LS42, Z104 74LS10). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Atari, Inc., Consumer Product Service, Tech Tip 2, "Revision B, Operating System ROMS", 28 May 1982, with enclosure 1, "400 Motherboard, placement". Reproduced in section 10 of the June 1982 field service manual, File:Atari 400 800 Field Service Manual June 82.pdf, PDF pages 211 to 213.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Howard W. Sams & Co., Computerfacts CC5, Atari Model 400, 1984: test equipment and tools, preliminary service checks (main board). Scan on the Internet Archive.