Atari 800 Operating System ROM Replacement

The operating system of the Atari 800 is held on a separate plug-in board, which Atari calls the ROM personality board or ROM module. It occupies memory from D800 to FFFF and carries three ROMs: two 4K chips, A401 and A403, holding the input/output routines, interrupt handling and the power-up and reset code, and a 2K chip, A402, holding the floating point maths package.[1] Atari revised the two 4K ROMs in 1982. Its Tech Tip 2 says that new 400 and 800 computers contain Revision B ROMs, that Revision A and Revision B must not be mixed because the system will not operate with one of each, and that the ROMs should be replaced if they are defective or if a printer overprints ("hiccups").[2] A failed ROM or ROM board shows as a green or yellow screen at switch-on, as a checksum failure in Atari's SALT II verify ROM test, or as a computer that starts but will not run a cartridge.[1][3]
| Position | Part | Atari number |
|---|---|---|
| A401 | ROM F, 4K | C014599 (Revision A: C014599A; Revision B: C014599B) |
| A403 | ROM E, 4K | C012499 (Revision A: C012499A; Revision B: C012499B) |
| A402 | ROM D, 2K | C012399 |
| Z401 | 74LS138 decoder | C014344 |
| Z402 | 74LS00 | C014341 |
| Z403 | 74LS09 | C014312 |
Symptoms
[edit | edit source]- A green or yellow screen at switch-on with no Memo Pad. Atari's chart checks for a defective RAM card first, starting with the lowest RAM slot, then swaps ROMs A401 to A403 on the personality board, then A303, Z303 and Z304 on the CPU board.[1]
- The computer does not come up although the power supply and the crystal X101 are good, and substituting the CPU board and the 16K RAM boards has not cured it: Sams says to check the personality board by substitution.[3]
- The computer comes up but a cartridge does not work: Sams again says to substitute the personality board.[3]
- A printer overprints: Atari's Tech Tip 2 says to replace the ROMs.[2]
- SALT II's verify ROM test reports FAIL for one or more ROMs.[1]
A black, grey or blue screen has other causes; see Atari 800 Black Screen Repair and the Atari 800 Troubleshooting Guide. RAM faults are in Atari 800 RAM Replacement. For a computer that comes up wrongly, Sams lists the motherboard's decoder Z101, the buffers Z105 and Z106, and Z102 for substitution.[3]
Safety
[edit | edit source]Switch the computer off before removing or fitting any chip or board; Atari's disassembly starts by turning the power switch off.[2][1] Use static precautions when handling the boards; Sams recommends anti-static mats, sprays, tools and materials.[3]
Tools and parts
[edit | edit source]- No tools to reach the module: Atari's procedure releases the cartridge door with its two clamps.[1]
- Replacement ROMs: a matched pair of the same revision for A401 and A403, and C012399 for A402. Atari's parts list fits all three in 24-pin sockets, with the logic chips Z401 to Z403 also socketed.[2][1]
- A known-good ROM module, for the substitution test that Atari's charts and Sams both use.[1][3]
- For the edge contacts: ZEP Safety Solvent or isopropyl alcohol, a dust-free cloth, an acid brush, a board cleaning brush and DS-ES contact lubricant, which Atari lists as "Libriplate (DS-ES Lubricant)".[1]
- Optional: SALT II, whose verify ROM test (V) checks each ROM's checksum.[1]
Procedure
[edit | edit source]Identify the revision
[edit | edit source]- Read the top of each 4K ROM. Atari's Tech Tip 2 says a Revision B part is printed with a copyright symbol followed by "1981 Atari".[2]
- Check that A401 and A403 are the same revision. A Revision A ROM paired with a Revision B ROM will not run.[2]
Find the failing ROM
[edit | edit source]With SALT II fitted:[1]
- Press V and RETURN to run the verify ROM test. The screen shows a checksum for each ROM and for the maths pack, with PASS or FAIL for each. If it passes, go on to the RAM test.
- If it fails, lock the test into continuous mode (press D, E, C and V, each followed by RETURN) so that it shows each ROM's checksum and PASS or FAIL.
- Replace and retest according to which ROM fails: A402 if ROM D fails, A403 if ROM E fails, A401 if ROM F fails, and all three if every ROM fails.
- If no single ROM accounts for the failure, swap Z401, Z402 and Z403 and run the test again.
- If it still fails, check for the φ2 clock at pin 10 of Z403. If φ2 is missing, trace it back to the CPU board and retest. If φ2 is present and the test still fails, Atari's chart goes no further and refers the technician to its technical support line.
Without SALT II, follow Atari's green or yellow screen chart: rule out the RAM cards, starting with the lowest slot, then swap A401 to A403 for known-good parts and check for a clear Memo Pad after each change.[1]

Remove the ROM module
[edit | edit source]- Turn the power switch off and open the cartridge door.[1]
- Turn the two cartridge door clamps towards the outside of the console.[1]
- Lift the cartridge door assembly a quarter of an inch, pull it towards you and lift it off.[1]
- Lift out the RAM modules, then the ROM module, then any cartridges.[1]
- Turn the cartridge door clamps back to their original position.[1]
Replace the ROMs
[edit | edit source]
- Take the board out of its case and find A401 and A403 using the silkscreen.[2]
- Remove the ROM, noting the orientation of its notch. If a board has its ROMs soldered in, see IC Removal and Socketing.
- Fit the replacement in the same orientation. When updating to Revision B, replace C014599A at A401 and C012499A at A403 with C014599B and C012499B, as a pair.[2]
- Inspect the socket contacts while the chip is out.
Clean the edge contacts
[edit | edit source]Atari gives this procedure for the CPU, RAM and ROM boards once they are out of the motherboard:[1]
- Inspect the contacts for flux, dirt, foreign material and deeply serrated fingers.
- Moisten the dust-free cloth with solvent and clean both sides of the fingers until they are free of old lubricant and dirt. Avoid touching the contacts afterwards.
- If corrosion or residue remains, moisten the board cleaning brush with solvent and brush the contacts firmly, four to six strokes, without touching any other part of the board. Then clean with the cloth again.
- Dip the acid brush in the lubricant and apply an even coat to both sides of the fingers, thick enough to protect them from corrosion, without spreading it beyond the fingers.
Refit the module
[edit | edit source]- Insert the ROM module in the slot closest to the keyboard, and at most three RAM modules in the remaining slots.[1]
- Set the cartridge door assembly on the top cover and slide it to the rear, so that its tab engages the aluminium casting.[1]
- Lock the door assembly down with the two clamps next to the cartridge slots.[1]
Testing
[edit | edit source]- Switch on with no cartridge: ATARI COMPUTER - MEMO PAD should appear.[1]
- Atari's Tech Tip 2 tests with the Stand Alone Test diagnostic (SALT); run the verify ROM test and check that every ROM passes.[2][1]
- Fit a cartridge, such as BASIC, and check that it runs; Sams ties a cartridge that will not work to the personality board.[3]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 Black Screen Repair
- Atari 800 RAM Replacement
- Atari 400 Operating System ROM Replacement
- Atari 1200XL Operating System ROM Replacement
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: ROM personality board (p. 1-15), 800 personality board schematic (figure 2-10, p. 2-15), power-up and verify ROM tests (pp. 3-2 and 3-11), access to the RAM and ROM boards (p. 4-8), RAM and ROM module installation, cartridge door assembly and PCB contact cleaning (pp. 4-20 and 4-21), 800 green/yellow screen chart (p. 7-6), 800 verify ROM chart (pp. 7-29 and 7-30), 800 parts list (p. 9-12: CA014090-01 10K ROM personality module, A401 C014599, A402 C012399, A403 C012499, Z401 74LS138, Z402 74LS00, Z403 74LS09, 24-pin sockets for A401 to A403). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 Atari, Inc., Consumer Product Service, Tech Tip 2, "Revision B, Operating System ROMS", 28 May 1982, with enclosure 2, "800 Personality Board, placement". Reproduced in section 10 of the June 1982 field service manual, File:Atari 400 800 Field Service Manual June 82.pdf, PDF pages 211, 212 and 214.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: preliminary service checks (power supply and keyboard), test equipment and tools, static electricity. Scan on the Internet Archive.