Atari 800 Controller Port Repair

The four controller jacks of the Atari 800, J110 to J113, are 9-pin right-angle connectors soldered to the front edge of the motherboard.[1] Each jack carries four joystick direction lines, a trigger and two paddle (pot) lines. The direction lines go through 220 Ω resistors to the PIA (A102), which also reads the paddle buttons; the pot lines go through 1.8 kΩ resistors to POKEY (A101); and the triggers go through 220 Ω resistors and the CPU board connector J101 to the CTIA or GTIA (A301) on the CPU board.[1][2] Sams' service data gives the pins to check for each port and two BASIC test programs.[2]
Symptoms
[edit | edit source]- A joystick direction or the fire button does nothing on one port, or on all four.[2]
- A paddle does not turn the player, or jumps, or its button does nothing.[2]
- Bent or broken pins in a jack: Atari's visual inspection checks the controller jacks for them.[1]
Try a known-good controller first, and the suspect controller on another computer. Sams' preliminary check for joysticks or paddles that do not work at all is to substitute the PIA (A102).[2] Controller faults are covered in Atari CX40 Circuit Board and Handle Replacement and Atari CX30 Potentiometer Cleaning and Replacement.
Safety
[edit | edit source]Pin 7 of each jack carries +5 V and pin 8 is ground.[1] Do not short pin 7 to ground while probing. Unplug the adaptor before lifting the motherboard out.
Tools and parts
[edit | edit source]- A logic probe, an oscilloscope and a meter.[2]
- A joystick and a pair of paddles known to work.
- Optional: SALT II with Atari's hand controller jack test connector, for the port test.[1]
- Parts as found: the PIA (Atari C014795, or C014812 as an alternative), POKEY (C012294), and the 9-pin right-angle connector for J110 to J113 (C010448, or C010727 as an alternative).[1]
The jacks
[edit | edit source]
| Pin | Signal | Path on the motherboard |
|---|---|---|
| 1 | Forward (up) | 220 Ω (R138 to R153) to the PIA, .001 µF to ground |
| 2 | Back (down) | As pin 1 |
| 3 | Left | As pin 1 |
| 4 | Right | As pin 1 |
| 5 | B pot | 1.8 kΩ (R130 to R137) to POKEY, with .047 µF (C127 to C134) and .001 µF (C135 to C142) to ground |
| 6 | Trigger | 220 Ω (R175 to R178), .001 µF (C194 to C197), to J101 and the CTIA or GTIA |
| 7 | +5 V | Bypassed by .001 µF at the jacks |
| 8 | Ground | – |
| 9 | A pot | As pin 5 |
The 400 uses the same pinout with 150 Ω series resistors in place of the 800's 220 Ω; see Atari 400 Controller Port Repair.[1]
Sams gives the chip pin for each paddle and paddle button:[2]
| Port | Paddle | POKEY (A101) pin | Button | PIA (A102) pin |
|---|---|---|---|---|
| 1 | 0 | 14 | 0 | 4 |
| 1 | 1 | 15 | 1 | 5 |
| 2 | 2 | 12 | 2 | 8 |
| 2 | 3 | 13 | 3 | 9 |
| 3 | 4 | 10 | 4 | 12 |
| 3 | 5 | 11 | 5 | 13 |
| 4 | 6 | 8 | 6 | 16 |
| 4 | 7 | 9 | 7 | 17 |
The paddle buttons share the left and right lines of their port, so the PIA pins in the table are also the left and right joystick lines. On the schematic the PIA's port A (pins 2 to 9) serves jacks 1 and 2 and port B (pins 10 to 17) jacks 3 and 4, four lines to each jack.[1][2]
Procedure
[edit | edit source]Test each port in BASIC
[edit | edit source]Fit the BASIC cartridge in the left slot. Sams' joystick program prints the readings for all four ports (BASIC numbers them 0 to 3):[2]
10 PRINT ,"JOYSTICK","BUTTON" 20 FOR P=0 TO 3 30 PRINT "PORT";P,STICK(P),STRIG(P) 40 NEXT P 50 FOR T=1 TO 200:NEXT T 60 GOTO 10
- Plug the joystick into the port under test and run the program. JOYSTICK should read 15 at rest and change to 14 for up, 13 for down, 11 for left and 7 for right; BUTTON should change from 1 to 0 when the button is pressed.[2]
- For paddles, use Sams' paddle program: change line 20 to
FOR P=0 TO 7and line 30 toPRINT "PADDLE";P,PADDLE(P),PTRIG(P). Each PADDLE reading should run from 228 to 1 as the knob is turned from minimum to maximum, and each button reading should change from 1 to 0 when pressed.[2]
Open the machine
[edit | edit source]- Remove the bottom cover (five screws), the two casting flange screws and the power supply board's lower left screw, disconnect the speaker, swing the top cover up, unplug the keyboard cable and set the top cover aside.[1]
- Unplug the RF cable and the power supply harness, remove the three power supply board screws and lift the board straight up.[1]
- Turn the unit upside down, remove the nine screws from the lower shield and lift the motherboard and shield out of the casting.[1]
- To free the motherboard from the lower shield, slide a screwdriver tip under the board next to each of the four nylon clips and gently raise the handle to pry the clip off; do not bend the connector pins or let the tip damage traces. Lift the motherboard off the shield.[1]
A joystick direction dead
[edit | edit source]- With the joystick in the failing port, put the logic probe on the PIA pin for that line and move the stick; the reading should go low. Sams' joystick check reads the PIA and the CTIA or GTIA (A301).[2]
- If it does not go low, check the jack contacts and the joystick switches.[2] On the schematic, also check the line's 220 Ω resistor and .001 µF capacitor.[1]
- If the readings are correct but the program does not see the movement, check A102 and A301 by substitution.[2]
Fire button dead
[edit | edit source]- Probe the trigger line while pressing the button; it should go low.[2]
- If it does not, check jack pin 6, the 220 Ω resistor (R175 to R178), the capacitor (C194 to C197) and the J101 contacts to the CPU board.[1]
- If it goes low but STRIG does not change, check A301 by substitution.[2]
Paddle dead
[edit | edit source]- Look up the paddle's POKEY pin and put the scope on it. The waveform should change from the sawtooth of Sams' figure 2 to the pulse of figure 3 as the paddle is turned.[2]
- If it is missing, check the port connector, the paddle's potentiometer and POKEY (A101) by substitution.[2] On the schematic, check the line's 1.8 kΩ resistor and its .047 µF and .001 µF capacitors.[1]
- For a dead paddle button, probe its PIA pin and press the button: it should go from high to low. If it does not, check the button switch and the port connector; if it does, check the PIA by substitution.[2]
Atari's port test legend divides pot-line failures, for each line, into a probable short to +5 V, an RC time constant that is too long and one that is too short.[1]
Repair a jack
[edit | edit source]- Inspect the jack for bent or broken pins.[1]
- Check continuity from each pin through its resistor to the chip pin, and from each capacitor to ground. See Continuity Testing and Signal Tracing.
- Replace a damaged jack with the motherboard off the shield; see Through-Hole Desoldering.
Reassemble
[edit | edit source]- With the motherboard right side up, snap on the four nylon clips of the lower shield and make sure all four are firmly seated. Plug in the CPU board with its component side away from the cartridge guide.[1]
- Turn the casting over, set the motherboard and lower shield into it with the CPU board in its slot, and refit the nine screws.[1]
- Refit the power supply board, the top cover and the bottom cover as in Atari 800 Power Supply Repair.[1]
Testing
[edit | edit source]Run the joystick and paddle programs on all four ports.[2] With SALT II, run the port test (P and RETURN) with the test connectors fitted; Atari's chart ends with a burn-in of at least eight hours.[1]
Related pages
[edit | edit source]- Atari 800
- Atari 800 Troubleshooting Guide
- Atari 800 SIO Port Repair
- Atari 800 Keyboard Repair
- Atari 400 Controller Port Repair
- Atari CX40
- Atari 400 800 Field Service Manual June 82
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 Atari, Inc., ATARI Home Computer Field Service Manual 400/800, May 1983 revision: 400 and 800 motherboard schematics (figures 2-2A and 2-6A, pp. 2-4 and 2-10: J110-J113, R130-R153, R175-R178, C127-C160, C194-C197, A101, A102), visual inspection (p. 4-21), 800 disassembly and assembly (pp. 4-9 to 4-14 and 4-17 to 4-18), 800 port test (pp. 7-33 and 7-34) and port test legend (table 7-3), 800 parts list (section 9: J110-113 C010448 or C010727, A101 C012294, A102 C014795 or C014812, R138-153 and R175-178 220 Ω). Scan on the Internet Archive. The June 1982 edition is hosted here as Atari 400 800 Field Service Manual June 82.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 Howard W. Sams & Co., Computerfacts CC7, Atari Model 800, 1984: preliminary service checks (main board), and troubleshooting, "Joysticks" and "Paddles" (port and pin chart, figures 2 and 3, and the two programs). Scan on the Internet Archive.