Jump to content

Atari 810 Clutch Cone and Eject Mechanism Adjustment

From RetroTechCollection
Atari 810 diskette eject block and latch lever (field service manual p. 6-43)
The eject mechanism at the right rear corner of the MPI transport: the block latch lever, the lever lifting arm and the diskette eject block (field service manual p. 6-43)

On the original Atari 810 with the MPI mechanism, the carrier assembly opens and closes with the front door and carries the clutching cone, which centres the diskette and clamps it to the spindle when the door is latched.[1][2] When the door is opened, the diskette eject block at the right rear corner of the transport is released from its latch and returns to its forward position.[3] Atari's troubleshooting guide traces a diskette that will not eject to the eject mechanism or to too little clearance between the clutch cone and the spindle with the door open, and a diskette that does not turn partly to a clutch cone that is not clamping it.[4] The field service manual sets both the cone clearance and the eject latch as part of refitting the carrier assembly.[5]

The Tandon mechanism fitted from November 1982 has a lift-up front latch and no eject mechanism, so this procedure does not apply to it.[6]

Symptoms

[edit | edit source]
  • The diskette stays in the drive when the door is opened.[4]
  • The diskette is scratched or pinched as it goes in or comes out.[7]
  • The diskette does not turn although the belt and motor work, because the clutch cone is not clamping it.[4]
  • The front door will not open; Atari's action is to adjust or replace the door latch mechanism.[4]

A diskette that does not turn because the belt is off or the motor does not run is covered in Atari 810 Drive Motor Repair; see also the Atari 810 Drive Troubleshooting guide.

Safety

[edit | edit source]
  • Unplug the transformer before opening the drive.
  • Keep magnetised tools away from the head, do not touch the head or pressure pad, and never lift the pressure pad arm further than the door would lift it in normal use: lifting it further distorts its spring and changes the pressure pad's loading on the head.[8][5]

Tools and parts

[edit | edit source]
  • Phillips screwdriver; a standard diskette for testing.[7]
  • Flat washers to shim the clutch cone shaft, added one at a time under the retaining clip.[7]
  • Atari's parts list gives the transport only as a complete assembly (CA014072) and lists no separate carrier, clutch cone or eject parts.[9]

Procedure

[edit | edit source]

Remove the transport

[edit | edit source]
  1. Remove the four adhesive covers on the top housing and the four screws under them, and lift the top housing off.[10]
  2. Disconnect the transformer and I/O cables, remove the five screws that hold the common baseplate to the base, and lift the baseplate out.[11]
  3. Remove the side board: disconnect the write protect and stepper harnesses (not polarised, so note how each sits), remove its three screws and lift it off the rear board's pins. Disconnect the head harness and the drive motor harness from the rear board.[12][13]
  4. Tip the assembly upside down and remove the four screws that hold the transport to the baseplate from underneath. Do not jar the transport.[14]

Remove the carrier assembly

[edit | edit source]
Atari 810 carrier assembly removal (field service manual p. 6-17)
The carrier assembly lifted off the transport, clear of the head assembly's pressure pad arm (field service manual p. 6-17)

Only needed if the carrier, door or clutch cone has to come off; the adjustments below are made with it fitted.

  1. Slide the head assembly all the way to the rear of its travel.[15]
  2. Loosen, but do not remove, the two screws that hold the carrier assembly to the rear of the transport casting, by about two full turns.[15]
  3. Of the four screws that hold the front panel bezel to the side guide assemblies and the casting, loosen the two bottom ones about four full turns and remove the two top ones.[15]
  4. Press the door release button to free the carrier from the door latch, lift the carrier just far enough to clear the latch, release the button and lower the door to a resting position.[8]
  5. Remove the two screws at the rear of the casting completely and pull the top of the bezel forward.[8]
  6. Lift the carrier out, tilting it slightly to clear the pressure pad arm. Do not lift the arm.[8]

Refit the carrier assembly

[edit | edit source]
  1. Tilt the bezel forward from both guide assemblies for clearance at the top.[5]
  2. Lower the carrier onto the casting, lifting the pressure pad arm only just enough to set it on its slide area on the carrier.[16]
  3. Fit the two rear screws with their split-ring lockwashers and flat washers, and tighten them slightly.[16]
  4. Push the bezel back, fit its two top screws and tighten all four bezel screws.[2]
  5. Latch the carrier closed at the bezel, centre the door horizontally in the bezel opening, and tighten the two rear carrier screws to 10 inch-pounds.[2]
  6. Press the door release button and check that the door opens and the carrier lifts the pressure pad arm.[2]

Set the clutch cone clearance

[edit | edit source]
Atari 810 clutch cone shaft retaining clip and shim washers (field service manual p. 6-42)
The clutch cone shaft above the carrier, with the retaining clip and the flat washers added as shims (field service manual p. 6-42)
  1. With the door open, look at the gap between the top edge of the diskette drive spindle and the bottom edge of the clutch cone. A diskette must move in and out without being scratched or pinched.[7]
  2. Test the ejection with a standard diskette. Too little clearance lets the back edge of the cone catch the edge of the diskette's hub hole and stop it being ejected.[7]
  3. To increase the clearance, press the clutch cone into the door arm so that the cone shaft comes up out of the top of the carrier.[7]
  4. Remove the retaining clip from the shaft, place another flat washer over the shaft and refit the clip.[7]
  5. Release the cone and check the gap and the ejection again; repeat until a diskette ejects cleanly.[7]

Set the eject latch

[edit | edit source]
  1. With the carrier open, push the diskette eject block at the right rear corner back until it latches in its rear position under the latch lever.[3]
  2. Close the carrier, then press the release button to open the door again.[3]
  3. Check that the eject block returned freely to its forward position as the carrier opened.[3]
  4. If it did not, bend either the latching lever or the lever lifting arm slightly, and repeat the check until the mechanism works.[3]

Reassembly

[edit | edit source]
  1. If the belt was taken off, refit and adjust it; see Atari 810 Drive Motor Repair.[3]
  2. Set the transport upside down, place the baseplate on it and fit the four #6-32 × 1/4 in screws with #6 split-ring lockwashers.[17]
  3. Reconnect the head harness to rear board connector 4 and the drive motor harness to connector 3, refit the side board with the stepper harness on its connector 2 and the write protect harness on connector 1, and refit the baseplate with its five screws.[13][18][19]
  4. Refit the top housing with its four screws and the screw hole covers.[20]

Testing

[edit | edit source]
  1. Insert and remove a standard diskette several times with the door opened normally; it should come out each time without being scratched or pinched.[7]
  2. Run Atari's floppy quick-check, including formatting a scratch diskette and booting the master diskette.[21]
[edit | edit source]

References

[edit | edit source]
  1. ↑ Atari, Inc., Atari 810 Disk Drive Field Service Manual (FS015854, Rev. 1, July 1980), p. 2-18: the clutching cone assembly centres and clamps the diskette to the spindle when the door is latched. Hosted as File:Atari 810 Disk Drive Field Service Manual FS015854 Rev 1.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-41, installing the carrier assembly, steps 4 to 9: bezel screws, centring the door, 10 inch-pound carrier screws, door release check.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-43, installing the carrier assembly, steps 15 to 21: eject block, latch lever and lever lifting arm, drive belt, transport.
  4. ↑ 4.0 4.1 4.2 4.3 Atari, Atari 810 Disk Drive Field Service Manual, pp. 5-3 to 5-5, troubleshooting guide: diskette does not turn (clutch cone not clamping diskette), diskette won't eject when the front door is opened (eject mechanism; clutch cone to spindle clearance too small), front door won't open (door latching mechanism).
  5. ↑ 5.0 5.1 5.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-39, installing the carrier assembly: cautions and step 1.
  6. ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 2 August 2026, mcurrent.name, section 3.2.1: the Tandon mechanism of November 1982 with a front latch and no eject mechanism. Community reference.
  7. ↑ 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-42, installing the carrier assembly, steps 10 to 14: spindle to clutch cone clearance, test with a standard diskette, retaining clip and added flat washer.
  8. ↑ 8.0 8.1 8.2 8.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-17, removing the carrier assembly, steps 9 to 12, and the caution about the pressure pad arm.
  9. ↑ Atari, Atari 810 Disk Drive Field Service Manual, final assembly parts list pp. 8-3 to 8-5: disk drive CA014072, with no separate carrier, clutch cone or eject parts.
  10. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-5, disassembling the drive case.
  11. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-6 and 6-7, removing the common baseplate.
  12. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-8 and 6-9, removing the side PCB.
  13. ↑ 13.0 13.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-50, reconnecting the head harness (rear PCB connector 4) and drive motor harness (connector 3).
  14. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-11, removing the drive transport.
  15. ↑ 15.0 15.1 15.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-16, removing the carrier assembly, steps 4 to 8.
  16. ↑ 16.0 16.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-40, installing the carrier assembly, steps 2 and 3.
  17. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-49, installing the drive transport.
  18. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-52 and 6-53, installing the side PCB.
  19. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-54 and 6-55, installing the common baseplate.
  20. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-56, assembling the drive case.
  21. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 4-3 to 4-10, floppy quick-check.