Jump to content

Atari 810 Drive Motor Repair

From RetroTechCollection
Atari 810 drive motor control voltages (Sams Computerfacts CD9 schematic)
The 810 drive motor circuit on the Sams schematic, with the voltages Sams measured while the drive was writing: PA1 from the PIA through J106 pin 9 and R145 to the motor drive array A107, the speed control R142, the TIP32A switch Q112, CR109 across the motor, and the drive motor M2 on J103

The Atari 810 turns the diskette with a DC motor that has a tachometer built in. The motor drives the spindle through a pulley, a belt and a flywheel, and the tachometer feedback circuit on the rear board varies the motor current to hold the diskette at 290 rpm ±1 %. The BUSY light is lit whenever the motor has power.[1] On the original rear board (CA014161) the motor is switched on by the PIA line PA1 and driven through the transistor array A107 and the TIP32A transistor Q112, and the speed is set with the 500 kΩ trimmer R142.[2][3] Atari's troubleshooting guide puts a diskette that does not turn down to the belt, the motor, the clutch cone or the motor circuit, and a slow or varying speed down to the tachometer lead, the write protect circuit, the belt, the motor circuit or seizing spindle bearings.[4]

The procedure is for the original two-board drive with the MPI mechanism. From February 1982 the "810 Analog" drives have an Analog Board on the mechanism with a frequency-to-voltage converter for the speed, and Page 6 places the speed control on that board.[5][6]

Symptoms

[edit | edit source]
  • The diskette does not turn. If the BUSY light comes on, the motor is being given power; if it does not, look first at the control side.[1]
  • The diskette turns slowly or the speed varies, giving read errors, mostly on the inner or outer tracks, or a drive that will not read diskettes written on other drives.[4]
  • The drive will not boot. Atari lists a wrong speed first among the causes.[4]

A drive that is completely dead has a supply fault; see Atari 810 Power Supply Repair. The checks for the other symptoms are in the Atari 810 Drive Troubleshooting guide.

Safety

[edit | edit source]
  • The drive runs from a mains transformer, and the rear board holds three 4,700 µF filter capacitors.[7] Unplug the transformer before disconnecting anything.
  • The drive contains static-sensitive MOS devices; work on a static-protected surface with a grounding strap.[8]
  • The head is easily magnetised and is damaged by dirt and skin oil. Keep magnetised tools away from the transport and do not touch the head or pressure pad.[9]

Tools and parts

[edit | edit source]
  • Multimeter. An oscilloscope or frequency counter for the speed check, or a software speed checker.[10][6]
  • A tensiometer reading 17 ±1 g for the yellow Mylar belt.[11]
  • Drive motor: Atari 3-35003-001 (0.300 in pulley) or 3-35003-002 (0.250 in pulley). The pulley fitted sets the tachometer frequency used for the speed adjustment.[10]
  • Q112: TIP32A in the Sams sample. A107: LM3086N in the Sams sample (Atari C010174). CR109: 1N4001. CR110: 1N914. R139: 1.1 Ω. R142: 500 kΩ trimmer. C142: 47 µF 16 V. C143: 10 µF 16 V.[2][7]

Procedure

[edit | edit source]

The motor connector J103

[edit | edit source]
Atari 810 rear board drive motor circuit (field service manual appendix D)
The drive motor circuit on Atari's rear board schematic CA014161 Rev. B (appendix D): J103, C120 and CR109 across the motor, Q112, the transistor array A107, the speed control R142 and the tachometer diode CR110

Atari and Sams number the five pins of the motor connector differently. Sams gives Atari's numbers in brackets on its schematic.[2][3]

Drive motor connector J103
Connection Atari pin (appendix D) Sams pin (CD9)
Motor positive, from Q112, with CR109 and C120 across the motor 2 4
Motor return, to ground through R139 (1.1 Ω) 3 3
Ground 1 and 4 5 and 2
Tachometer output, to CR110 5 1

The second tachometer lead does not go to J103. It runs to pin 3 of the write protect connector J101 on the side board.[2] Atari's cure for a slow or varying speed caused by this lead being out of place is to connect the green motor harness lead to the centre terminal of the write protect harness.[4]

Check the belt and the clutch

[edit | edit source]
  1. Open the drive: remove the four adhesive covers on the top housing and the four screws under them, and lift the top housing off.[12]
  2. Disconnect the transformer and I/O cables, remove the five screws that hold the common baseplate to the base, and lift the baseplate out.[13]
  3. Turn the baseplate over. The flywheel and the belt can be seen through the large circular hole in the metal baseplate.[6]
  4. If the belt is off the flywheel or the motor pulley, or broken, refit or replace it (below).[4][14]
  5. If the belt is in place and the motor turns but the diskette does not, the clutch cone is not clamping the diskette; Atari's action is to adjust or replace the clutch cone assembly.[4]

Check the motor and its wiring

[edit | edit source]

Sams measures these at J103 on the rear board, using its own pin numbers (see the table).[15]

  1. Check that J103 is fully seated.[15]
  2. Measure from J103 pin 3 to ground. Expect 1.1 Ω. If it is higher, check R139.[15]
  3. Measure the motor winding: 7.8 Ω between pins 3 and 4, and 9.1 Ω between pins 4 and 5.[15]
  4. Measure the tachometer winding: 178.5 Ω. Sams' text gives this between pin 1 of J105 and pin 3 of J101; its schematic draws the tachometer between J103 pin 1 and J101 pin 3.[15][2]
  5. If any reading is wrong, replace the motor (below).[15]

Check the motor drive circuit

[edit | edit source]

Sams' voltages were taken while an Atari 800 wrote to the drive over and over.[16] See Continuity Testing and Signal Tracing and Testing Diodes, Transistors and Regulators.

  1. Command the drive to read or write and measure the cathode of CR109, the positive side of the motor. Expect about 5 V; Sams shows 4.8 V at the collector of Q112.[14][2]
  2. If the 5 V is present and the motor does not turn, replace the motor.[14]
  3. If it is missing, check the motor drive array A107 and the switch transistor Q112 by substitution.[14] Sams shows about 11.7 V at the base of Q112 with the motor running.[2]
  4. Check the control from the side board. Sams expects 1.7 V on pin 9 of the PIA A104, and a logic low on pin 14 of A104 while the drive is running that goes high when it stops. Its main troubleshooting page also gives about 0.1 V at rest and 5 V when running on pin 25 of A104. If these are wrong, Sams substitutes A104, then the controller A105, the processor A101 and the ROM A102.[14][15]

Atari's theory section describes the motor supply as the unregulated 9 to 10 V DC; the Sams schematic draws the emitter of Q112 from the regulated 12.0 V source.[17][2]

Remove the transport

[edit | edit source]
  1. With the baseplate out of the base, remove the side board. Disconnect the write protect and stepper harnesses (the plugs are not polarised, so note how each sits), remove the three screws holding the board and its ground bracket, and lift it straight up off the rear board's pins.[18]
  2. Disconnect the head harness (J109) and the drive motor harness (J103) from the rear board.[19][20]
  3. Tip the baseplate and transport upside down, remove the four screws that hold the transport to the baseplate from underneath, and lift the transport off. Do not jar it; it holds the drive's mechanical alignments.[21]

Replace the belt

[edit | edit source]
Atari 810 drive belt and flywheel (field service manual p. 6-14)
The flywheel and drive belt on the underside of the MPI transport (field service manual p. 6-14)

The transport has either the older yellow Mylar belt or the newer black neoprene belt.[11] See also Drive Belt Replacement.

  1. Lay the transport on its side.[22]
  2. Take the old belt off by turning the large flywheel while easing the belt off its outside edge, so that it is not stretched.[22]
  3. Loop the new belt over the motor drive hub and ease it onto the flywheel while turning the flywheel. Do not stretch it; a stretched belt changes the diskette speed and causes read and write errors.[23]
  4. Adjust the belt with the power off. For the Mylar belt, loosen the two motor screws, move the motor until either leg of the belt reads 17 ±1 g on the tensiometer, and tighten the screws. For the neoprene belt, loosen the two motor screws, hold the motor as close to the spindle and flywheel as it will go, and tighten the screws.[11]

Replace the motor

[edit | edit source]
Atari 810 drive motor removal (field service manual p. 6-15)
The drive motor lifted off the transport casting, with its two screws, lockwashers and flat washers below (field service manual p. 6-15)
  1. Remove the belt as above.[24]
  2. Disconnect the single black ground lead that runs from the motor harness to the transport casting.[24]
  3. Support the motor with one hand and remove the two screws that hold it to the casting, then lift it off.[24]
  4. Lay the transport on its side and set the new motor on the top side of the casting, with its wiring harness leaving the motor towards the centre rear of the transport.[25]
  5. Holding the motor, fit the two screws with their split-ring lockwashers and flat washers, and tighten them to 10 inch-pounds.[25]
  6. Refit the belt and adjust it as above.[25][23]
  7. Reconnect the black ground lead to a faston lug at the rear of the transport.[26]

Refit the transport

[edit | edit source]
  1. Set the transport upside down, place the baseplate on it, and fit the four #6-32 × 1/4 in screws with #6 split-ring lockwashers.[27]
  2. Turn the assembly the right way up and reconnect the head harness (shielded red, blank, blue, and white and black) to rear board connector 4, and the drive motor and ground harness (yellow, green, blue, red, black) to rear board connector 3. Appendix F of the manual shows an alternate harness arrangement.[20]
  3. Refit the side board, reconnect the stepper harness to its connector 2 and the write protect harness to its connector 1, and refit the baseplate with its five screws.[28][29]

Set the speed

[edit | edit source]

Atari sets the speed with the drive reading any track: put an oscilloscope on the anode of CR110 and adjust R142 until the tachometer frequency matches the belt and motor pulley fitted, 390 Hz for a Mylar belt with a 0.250 in pulley, 320 Hz for a Mylar belt with a 0.300 in pulley, and 305 Hz for a neoprene belt with a 0.300 in pulley.[10] Page 6 describes doing it with a software speed checker; R142 is the white disc trimmer in the back left-hand corner of the rear board, clockwise to slow the drive and anticlockwise to speed it up.[6] The full procedure is on the maintenance guide. The washers between the flywheel, casting and spindle also affect the speed, so keep every one if the flywheel is removed.[30]

Testing

[edit | edit source]
  1. Switch on and check that the BUSY light comes on and goes out.[31]
  2. Boot a diskette and check the speed with an oscilloscope on CR110 or a speed checker.[10][6]
  3. Run Atari's floppy quick-check, including formatting a scratch diskette (709 free sectors) and loading a program from a diskette written on another drive.[31]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 Atari, Inc., Atari 810 Disk Drive Field Service Manual (FS015854, Rev. 1, July 1980), p. 2-18, diskette drive motor and logic: DC motor with internal tachometer, tach feedback, 290 rpm ±1 %, pulley, belt, flywheel and spindle, clutching cone, BUSY light on whenever the motor is supplied with power. Hosted as File:Atari 810 Disk Drive Field Service Manual FS015854 Rev 1.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Howard W. Sams & Co., Computerfacts CD9, Atari Model 810 (June 1986), schematic, p. 2 (PDF page 3): PA1, P101/J106 pin 9, R145, A107 LM3086N, R142 500K, R139 1.1, Q112 TIP32A (11.7 V base, 4.8 V collector), C142, CR109, C120, J103 with bracketed pin numbers, tachometer to J101 pin 3, the 12.0 V source. Hosted as File:Sams Computerfacts CD9 Atari 810 Disk Drive.pdf.
  3. ↑ 3.0 3.1 Atari, Atari 810 Disk Drive Field Service Manual, appendix D, p. 9-6: schematic of the rear board CA014161 Rev. B (J103, CR109, C120, Q112, A107, R137 to R145, C142 to C144, CR110).
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Atari, Atari 810 Disk Drive Field Service Manual, pp. 5-3 to 5-7, troubleshooting guide: diskette does not turn; diskette speed slow or varying (green motor harness lead to the centre terminal of the write protect harness); will not boot; read errors.
  5. ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 2 August 2026, mcurrent.name, section 3.2.1: the 810 Analog boards of February 1982 and their tachometer frequency-to-voltage converter. Community reference.
  6. ↑ 6.0 6.1 6.2 6.3 6.4 Garry Francis, "Adjust It!", Page 6 no. 25 (January/February 1987), p. 54, page6.org (retrieved 2026-10-25): the flywheel seen through the hole in the baseplate, setting the 810 speed with a software checker, R142 and its position, the later speed-regulating board and its R104. Magazine article.
  7. ↑ 7.0 7.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 8-8 to 8-10, rear board parts list CA014161: C146, C148, C149 4700 µF; C142 47 µF 16 V; C143 10 µF 16 V; CR109 1N4001; CR110 1N914; R139 1.1 Ω; R142 500K variable; A107 transistor array C010174.
  8. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-3, special notes: static-sensitive MOS devices, torque limits, non-polarised harnesses.
  9. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-31, cautions on the head: magnetisation, dirt and oils, pressure pad arm.
  10. ↑ 10.0 10.1 10.2 10.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 7-10, speed adjustment guide: tachometer frequency at the anode of CR110, R142, and drive motor part numbers 3-35003-001 and 3-35003-002 by pulley diameter.
  11. ↑ 11.0 11.1 11.2 Atari, Atari 810 Disk Drive Field Service Manual, pp. 7-13 and 7-14, drive belt adjustment.
  12. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-5, disassembling the drive case.
  13. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-6 and 6-7, removing the common baseplate.
  14. ↑ 14.0 14.1 14.2 14.3 14.4 Sams, Computerfacts CD9, preliminary service checks, p. iii, check 3 (drive motor does not turn disk): belt, 1.7 V on pin 9 of A104, logic on pin 14 of A104, 5 V at the cathode of CR109, the drive motor, A107 and Q112.
  15. ↑ 15.0 15.1 15.2 15.3 15.4 15.5 15.6 Sams, Computerfacts CD9, p. 12, troubleshooting, disk drive inoperative: J103, 1.1 Ω to ground and R139, winding resistances of 7.8, 9.1 and 178.5 Ω, pins 25 and 14 of A104, substitution of A104, A105, A101 and A102.
  16. ↑ Sams, Computerfacts CD9, p. 13, schematic notes: voltages measured while an Atari 800 runs the BASIC disk test program.
  17. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 2-20, power supply: the unregulated 9-10 V DC diskette drive motor supply.
  18. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-8 and 6-9, removing the side PCB.
  19. ↑ Sams, Computerfacts CD9, p. 13, disassembly instructions, rear (analog) board removal: J103 and J109.
  20. ↑ 20.0 20.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-50, connecting the head harness to rear PCB connector 4 and the drive motor and ground harness to rear PCB connector 3.
  21. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-11, removing the drive transport.
  22. ↑ 22.0 22.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-14, removing the transport drive belt.
  23. ↑ 23.0 23.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-45, installing the transport drive belt.
  24. ↑ 24.0 24.1 24.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-15, removing the transport drive motor.
  25. ↑ 25.0 25.1 25.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-44, installing the drive motor.
  26. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-35, step 18: the black ground lead of the drive motor harness goes to one of the faston lugs at the rear of the transport.
  27. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-49, installing the drive transport.
  28. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-52 and 6-53, installing the side PCB.
  29. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-54 and 6-55, installing the common baseplate.
  30. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-18, removing the flywheel: the number and placement of the washers helps to determine diskette speed.
  31. ↑ 31.0 31.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 4-3 to 4-10, floppy quick-check.