Jump to content

Atari 810 Stepper Motor Replacement

From RetroTechCollection
Atari 810 stepper motor drivers (Sams Computerfacts CD9 schematic)
The 810 stepper circuit on the Sams schematic: PIA lines PB2 to PB5 drive the MPSA06 transistors Q106 to Q109, which switch the four windings of the stepping motor M4 on J102 pins 1 to 4; the common, J102 pin 5, is fed through R125 (1.1 ohms) from the 11.2 V supply on J106 pin 20

The Atari 810 moves its head with a four-phase stepper motor of 3.6 degrees per step. A steel band wrapped round a pulley on the motor shaft turns each step into one track of head movement, and the four phases are driven from lines of the PIA on the side board.[1] On the original drive the PIA lines PB2 to PB5 switch the windings through the MPSA06 transistors Q106 to Q109, with the 1N4001 diodes CR101 to CR104 across them, and the common of the windings is fed through the 1.1 Ω resistor R125.[2][3] A stepper that does not move leaves the drive unable to find track 00 or boot. Atari replaces a faulty stepper motor, and after any work on the stepper or its band the radial alignment and the track 00 stop must be set again.[4][5]

The procedure is for the MPI mechanism described in Atari's 1980 field service manual. Drives fitted with the Tandon mechanism from November 1982 adjust the stepper with a cam screw at the rear of the mechanism instead.[6]

Symptoms

[edit | edit source]
  • The drive will not boot and the head does not step; Atari lists a faulty stepper motor, a track 00 stop out of adjustment and radial misalignment among the causes.[4]
  • Radial alignment will not hold when the head is stepped to track 00 or track 32 and back. Atari's list of suspects is a broken or damaged setscrew, a binding or misaligned positioning band, the head carriage binding on its guide rods, or a bad stepper motor.[7]

Occasional read errors on all tracks point first at the diskette, a dirty or magnetised head or a worn pressure pad; see the Atari 810 Maintenance Guide and the Atari 810 Drive Troubleshooting guide.[4]

Safety

[edit | edit source]
  • Unplug the transformer before working inside the drive.
  • The drive contains static-sensitive MOS devices; work on a static-protected surface with a grounding strap.[8]
  • The head is easily magnetised and is damaged by dirt and skin oil. Use non-magnetised tools near the transport and do not touch the head or the pressure pad.[9]
  • The positioning band is delicate. Do not kink or damage it.[10]

Tools and parts

[edit | edit source]
  • Multimeter.
  • 0.050 in hex setscrew driver.[11]
  • For the alignment afterwards: an oscilloscope with A+B and channel B invert, an Atari computer with at least 16 KB, the disk alignment cartridge or program, a master alignment diskette, a non-conductive tuning wand and a 0.010 in feeler gauge.[11][12]
  • Driver parts on the side board: Q106 to Q109 (MPSA06, Atari C014394), CR101 to CR104 (1N4001), R121 to R124 (1 kΩ), R125 (1.1 Ω).[3][2]
  • Stepper motor: neither source lists it as a separate part. Atari's parts list gives the transport only as a complete assembly (CA014072), and Sams' instruction for a stepper with an open winding is to replace the drive mechanism.[3][13]

Procedure

[edit | edit source]

Check the stepper circuit

[edit | edit source]

Sams uses the pin numbers of its own schematic for J102. See Continuity Testing and Signal Tracing and Testing Diodes, Transistors and Regulators.

  1. Check that the stepper plug J102 and the side board connection to the rear board (P101/J106) are seated.[13]
  2. With the drive on, measure J102 pins 1 to 5. Expect about 12 V on each.[14][13]
  3. If pin 5 has no voltage, check for 12 V at pin 20 of J106, which carries the 11.2 V unregulated supply from the rear board, and check R125 for 1.1 Ω.[14][13][2]
  4. If R125 is open, check the stepper winding resistances as well as replacing the resistor.[13]
  5. If pin 5 is live but pins 1 to 4 are not, switch off and measure the windings between pin 5 and each of pins 1 to 4. Sams' troubleshooting text gives 75 Ω for each; its schematic marks each winding 7.3. An open winding means a new stepper.[14][2]
  6. If all five pins have 12 V and the motor still does not step, Sams substitutes the PIA A104, then replaces the side board.[13] Between the PIA and the windings the schematic shows the drivers Q106 to Q109 and the diodes CR101 to CR104 on the side board; test them on the diode range before condemning the board.[2]

Remove the transport

[edit | edit source]
  1. Remove the four adhesive covers and the four screws from the top housing and lift it off.[15]
  2. Disconnect the transformer and I/O cables, remove the five screws holding the common baseplate to the base, and lift the baseplate out.[16]
  3. Disconnect the write protect harness and the stepper motor harness (black, white, red, green, brown) from the side board, noting how each non-polarised plug sits, remove the three screws holding the side board, and lift it off the rear board's pins.[17]
  4. Disconnect the head harness and the drive motor harness from the rear board.[18][19]
  5. Tip the assembly upside down and remove the four screws that hold the transport to the baseplate from underneath. Do not jar the transport.[20]

Remove the stepper motor

[edit | edit source]
Atari 810 stepper pulley setscrew and securing nuts (field service manual p. 6-25)
The positioning band pulley lifted off the stepper shaft, with its setscrew and the two nuts that hold the stepper to the casting (field service manual p. 6-25)
  1. Find the two screws that hold the positioning band to the right side of the head assembly.[10]
  2. Remove the rear screw, noting the screw and washer arrangement and taking care not to crimp the band.[10]
  3. Slide the head carriage forward to reach the front band screw, and remove it, again noting the screw and washer arrangement.[10]
  4. Back the hex setscrew that holds the band pulley to the stepper shaft (on the top side of the casting) out about one turn anticlockwise.[21]
  5. Lift the band and pulley off the stepper shaft and set them aside.[21]
  6. Lay the casting on its left side. Supporting the stepper with your right hand, remove the two nuts that hold it to the casting.[21]
  7. Separate the stepper from the casting, pulling its wiring harness out of the slot in the casting.[21]

Fit the stepper motor

[edit | edit source]
Atari 810 positioning band screws and special bracket washer (field service manual p. 6-29)
The two band screws on the head assembly; the rear one takes the special bracket washer (field service manual p. 6-29)
Atari 810 tensioning the positioning band (field service manual p. 6-30)
Hooking the small hole at the front of the band with a pointed tool and pulling it forward while the front screw is tightened (field service manual p. 6-30)
  1. Fit the split rubber grommet on the stepper wiring harness.[22]
  2. Lay the transport on its left side and set the stepper against the underside of the casting, with its harness towards the rear centre of the casting.[22]
  3. Fit a flat washer, a split-ring lockwasher and a 1/4 in hex nut on each of the two stud bolts that come through the top of the casting, and tighten the nuts lightly.[23]
  4. Slide the band pulley onto the stepper shaft on the top of the casting. If it does not slide on easily, back its setscrew out a little further. Do not tighten the setscrew yet.[23]
  5. Position the head assembly so that the band can be fixed to its right rear corner, and fit the rear screw with its split-ring lockwasher and the special bracket washer, without tightening it.[24]
  6. Pull the front section of the band forward until its screw hole lies over the hole at the front corner of the head assembly, and fit the screw with its split-ring lockwasher and flat washer, without tightening it.[24]
  7. Slide the head assembly gently back and forth on its guide rods to centre the band pulley on the stepper shaft.[24]
  8. Tighten the rear band screw. Do not exceed 6 inch-pounds, since the screw goes into plastic.[24]
  9. Hook a pointed tool, such as the point of a craft knife, into the small hole at the front end of the band, pull the band slightly forward, and tighten the front band screw while holding it.[25]
  10. Slide the harness grommet up into the slot at the rear of the casting.[25]

Reassemble

[edit | edit source]
  1. Set the transport upside down, place the baseplate on it and fit the four #6-32 × 1/4 in screws with #6 split-ring lockwashers.[26]
  2. Reconnect the head harness to rear board connector 4 and the drive motor harness to connector 3.[18]
  3. Refit the side board, reconnect the stepper harness to its connector 2 and the write protect harness to connector 1, and fit its three screws.[27]
  4. Fit the baseplate into the base with its five screws, with a rubber washer on every boss.[28] Leave the top housing off until the adjustments are done.[5]

Align the head

[edit | edit source]

The band pulley is still loose on the stepper shaft; the radial alignment sets its position. The full steps are on the maintenance guide.[5]

  1. With the drive connected and the BUSY light off, insert the master alignment diskette, load the alignment cartridge or program and command the drive to read track 16.[29]
  2. Set the oscilloscope to A+B with B inverted, 20 ms/div and 20 mV/div. Ground it to the faston lug at the rear of the transport and put the probes on the rear leads of C154 and C155.[29]
  3. If the two cat's-eye lobes are unequal, back the pulley setscrew out about a quarter turn, turn the pulley slightly until the lobes are equal, and tighten the setscrew.[30]
  4. Step to track 00 and back to track 16, then to track 32 and back. The lobes must stay within 80 % of each other each time; if not, repeat the adjustment.[30][7]
  5. Set the track 00 stop: read track 00 and set the stop setscrew at the rear of the transport for 0.010 in clearance to the rear corner of the head carriage moulding, then step out past track 30 and back and check that the carriage does not butt against the setscrew.[12]

Testing

[edit | edit source]
  1. Refit the top housing with its four screws and the screw hole covers.[31]
  2. Run Atari's floppy quick-check: boot the master diskette, format a scratch diskette and check for 709 free sectors, and load a program from a diskette written on another drive.[32]

Revision notes

[edit | edit source]

Atari's theory section says the stepper is supplied with "a nominal 9 to 10 VAC"; the Sams schematic feeds it from the 11.2 V unregulated DC through R125. The FAQ records that from 1 September 1981, when the data separator board was fitted, the stepper circuit was moved to a regulated 12 V. A label on the Sams schematic says the external data separator board plugs into the A105 socket, and Sams still draws the 11.2 V feed. Measure the supply on the drive being repaired.[1][2][6]

[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 Atari, Inc., Atari 810 Disk Drive Field Service Manual (FS015854, Rev. 1, July 1980), p. 2-17, stepper motor and logic: four-phase motor, 3.6 degrees per step, steel band, one step per track, four PIA phase lines, "a nominal 9 to 10 VAC" supply. Hosted as File:Atari 810 Disk Drive Field Service Manual FS015854 Rev 1.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 Howard W. Sams & Co., Computerfacts CD9, Atari Model 810 (June 1986), schematic, p. 2 (PDF page 3): PB2-PB5, R121-R124, Q106-Q109 MPSA06, CR101-CR104 1N4001, J102 pins 1-5, stepping motor M4 with windings marked 7.3, R125 1.1 Ω from P101/J106 pin 20 (11.2 V source), R120, and the note that the external data separator board plugs into the A105 socket. Hosted as File:Sams Computerfacts CD9 Atari 810 Disk Drive.pdf.
  3. ↑ 3.0 3.1 3.2 Atari, Atari 810 Disk Drive Field Service Manual, parts lists pp. 8-3 to 8-7: disk drive (transport) CA014072; side board CA014162 with R125 1.1 Ω, R121-R124 1K, CR101-CR104 1N4001, transistors Q106-Q109 C014394.
  4. ↑ 4.0 4.1 4.2 Atari, Atari 810 Disk Drive Field Service Manual, pp. 5-3 to 5-7, troubleshooting guide: drive will not boot (cannot find track 00, stepper motor faulty, radial misalignment); occasional read errors on all tracks.
  5. ↑ 5.0 5.1 5.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-55: after reassembly, head cleaning and demagnetisation, radial track alignment, speed adjustment and track 00 stop adjustment.
  6. ↑ 6.0 6.1 Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 2 August 2026, mcurrent.name, section 3.2.1: the data separator change of 1 September 1981 (stepper motor circuit moved to a regulated 12 V) and the Tandon mechanism with its cam screw. Community reference.
  7. ↑ 7.0 7.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 7-8 and 7-9: the note on what to suspect if the alignment will not hold.
  8. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-3, special notes: static-sensitive devices, torque limits, non-polarised harnesses.
  9. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-31, cautions on the head.
  10. ↑ 10.0 10.1 10.2 10.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-24, removing the stepper motor: the two positioning band screws, and the caution that the band is delicate.
  11. ↑ 11.0 11.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 7-5, radial track alignment: equipment, and the BUSY light caution.
  12. ↑ 12.0 12.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 7-11 and 7-12, track 00 stop adjustment.
  13. ↑ 13.0 13.1 13.2 13.3 13.4 13.5 Sams, Computerfacts CD9, preliminary service checks, p. iii: check 1 (C) to (F) (P101 and J106, 12 V at pin 20 of P101, R125 1.1 Ω, winding resistances, replace the drive mechanism) and check 4 (J102, 12 V at J102 pins 1 to 5, windings, substitute A104, replace the CPU board).
  14. ↑ 14.0 14.1 14.2 Sams, Computerfacts CD9, p. 12, troubleshooting, stepping motor inoperative: 12 V at J102 pins 1 to 5, 12 V at J106 pin 20, 75 Ω windings between pin 5 and pins 1 to 4, replace the stepping motor if a winding is open.
  15. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-5, disassembling the drive case.
  16. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-6 and 6-7, removing the common baseplate.
  17. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-8 and 6-9, removing the side PCB.
  18. ↑ 18.0 18.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-50, reconnecting the head harness (rear PCB connector 4) and the drive motor harness (connector 3).
  19. ↑ Sams, Computerfacts CD9, p. 13, disassembly instructions, rear board removal: J103 and J109.
  20. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-11, removing the drive transport.
  21. ↑ 21.0 21.1 21.2 21.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-25, removing the stepper motor: pulley setscrew, band and pulley, the two securing nuts, harness out of the chassis slot.
  22. ↑ 22.0 22.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-27, installing the stepper motor, steps 1 to 3.
  23. ↑ 23.0 23.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-28, installing the stepper motor, steps 4 and 5.
  24. ↑ 24.0 24.1 24.2 24.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-29, installing the stepper motor, steps 6 to 11: band screws, special bracket washer, centring the pulley, 6 inch-pound limit.
  25. ↑ 25.0 25.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-30, installing the stepper motor, steps 12 to 15.
  26. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-49, installing the drive transport.
  27. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-52 and 6-53, installing the side PCB.
  28. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-54, installing the common baseplate.
  29. ↑ 29.0 29.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 7-6, radial track alignment, steps 1 to 9. Step 8 prints "CR154"; the parts list has C154.
  30. ↑ 30.0 30.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 7-7 and 7-8, radial track alignment, steps 10 and the hysteresis checks.
  31. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-56, assembling the drive case.
  32. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 4-3 to 4-10, floppy quick-check.