Jump to content

Atari 810 Power Supply Repair

From RetroTechCollection
Atari 810 power supply voltages (Sams Computerfacts CD9 schematic)
The 810 power supply on the Sams schematic, with the voltages Sams measured: the bridge CR111 to CR114, the 7805 regulator A108 (11.2 V in, 5.0 V out), the doubler CR115 and CR116 feeding the TIP32A regulator Q113 (25.1 V in, 12.0 V out), and the negative doubler that lights the power LED CR108 and feeds the zener CR107

The original Atari 810 makes all of its supply voltages from the 9 V AC of an external transformer. The PWR switch on the front panel passes the AC to a full-wave bridge rectifier, and the supply produces an unregulated 9 to 10 V DC for the drive motor, a regulated +5 V, a regulated +12 V made from a voltage doubler, and a zener-regulated -5 V made from a second doubler. The power LED is lit through the -5 V section.[1] Most of the circuit is on the rear board (CA014161), but the switch, the -5 V zener and the LED are on the side board, and the +5 V regulator A108 and the +12 V pass transistor Q113 are bolted to the common baseplate, which is their heatsink.[2][3] Best Electronics, which sells 810 parts, finds that a drive that is dead, or that lights its LEDs and does nothing mechanical, usually has a faulty rear power board, and that the single rear power board of the early drives also suffers from speed problems.[4]

The procedure is for the original two-board drive described in Atari's 1980 field service manual and the Sams Computerfacts. Drives built from February 1982 (the "810 Analog") have a Power Supply Board and an Analog Board in place of the rear board, and neither document covers them.[5]

Symptoms

[edit | edit source]
  • The drive is dead: no power LED, no BUSY light and no motor.[6]
  • The power LED lights but the drive motor never runs. Sams points first at the motor windings; see Atari 810 Drive Motor Repair.[6]
  • The LEDs light but nothing moves; Best Electronics puts this down to the rear power board in most drives.[4]
  • The power LED stays out. The LED is lit through the -5 V section, so check the -5 V rail and the zener CR107 as well as the LED CR108.[1][7]

A diskette that does not turn while the rest of the drive works is usually the belt or the motor circuit, not the supply; see Atari 810 Drive Motor Repair.[8]

Safety

[edit | edit source]
  • The transformer is a mains device. Measure its output with it plugged in at the wall, and keep the drive end of the lead clear of the board.
  • The rear board holds three 4,700 µF filter capacitors (C146, C148 and C149).[2] Unplug the transformer and let them discharge before touching the board.
  • The drive contains static-sensitive MOS devices. Atari asks for a static-protected work surface and a grounding strap.[9]

Tools and parts

[edit | edit source]
  • Multimeter with AC and DC voltage, resistance and diode-test ranges. An oscilloscope shows the ripple on the filter capacitors.
  • Regulator A108: a 7805 (Atari C014348; 7805C in the Sams sample).[2][10]
  • Pass transistor Q113: TIP32A in the Sams sample.[10] It sits on a mica insulator (C014811) with a shoulder washer (C014814), fixed by a #4-40 × 3/8 in screw, a #4 split-ring lockwasher and a #4 nut. A108 is fixed by a #4 × 1/4 in thread-forming screw.[2][3]
  • Heat transfer compound.[3]
  • Rear board parts: bridge diodes CR111 to CR114 (MR501, C014398); doubler diodes CR115 to CR118 (1N4001); error amplifiers Q114 and Q115 (MPSA06, C014394); C146, C148 and C149 (4,700 µF 25 V, C014780); C150 and C151 (470 µF 16 V, C014368).[2]
  • Side board parts: zener CR107 (1N5231B, 5.1 V, C014808-01) and R132 (330 Ω).[2]
  • The full list of electrolytics is on the Atari 810 Capacitor Replacement Guide; the general method is in Capacitor Replacement Procedure.

Procedure

[edit | edit source]

Expected values

[edit | edit source]

Sams measured these with a digital meter while an Atari 800 ran a BASIC program that wrote to the drive over and over.[11]

Atari 810 supply voltages (Sams Computerfacts CD9)
Point Expected Notes
Transformer output plug 10.9 V AC Sams troubleshooting, p. 12[7]
Bridge output, cathode of CR111 12.0 V Sams troubleshooting, p. 12[7]
A108 input (pin 1) 11.2 V, with about 0.8 V peak to peak of ripple Sams schematic; Sams calls this the 11.2 V source[10]
A108 output (pin 3) 5.0 V Sams schematic[10]
Q113 input, doubler output (J105 pin 3) 25.1 V, with about 0.7 V peak to peak of ripple Sams schematic[10]
Q113 output (J105 pin 2) 12.0 V Sams schematic[10]
Anode of CR107 -5.0 V Sams troubleshooting and schematic[7][10]

Sams numbers the baseplate pins of A108 as J10 pins 1 to 3 and those of Q113 as J105 pins 1 to 3; Atari's schematic labels the same pins J104A to J104C and J105A to J105C.[10][12]

Opening the drive

[edit | edit source]
  1. Remove the four adhesive covers on the top housing and the four screws under them, and lift the top housing off the base.[13]
  2. Disconnect the transformer lead from the PWR jack and any I/O cables, remove the five screws holding the common baseplate to the base, and lift the baseplate out. The front coverplate comes out with it. Each boss in the base has a rubber washer on top.[14]
  3. Set the baseplate on a static-protected surface.[14]

Trace the supply

[edit | edit source]
Atari 810 rear board power supply schematic (field service manual appendix D)
The power supply on Atari's rear board schematic CA014161 Rev. B (appendix D): J110, the bridge CR111 to CR114, A108 on J104, the doubler CR115, CR116, C148 and C149, Q113 on J105 with its error amplifiers Q114 and Q115, and the negative doubler C150, C151, CR117 and CR118

The AC comes in on the power jack J110 on the rear board. One side of it goes straight to the bridge; the other goes to the side board through J106 pin 2, through the power switch S102, and back through pin 1 to the bridge.[10][12] See Continuity Testing and Signal Tracing for the method.

  1. Measure the transformer at its output plug. Expect about 10.9 V AC; if it is missing, the transformer is faulty.[7]
  2. Plug it in, switch the drive on and measure the DC at the cathode of CR111. Expect about 12 V. If it is missing, check J110, the bridge diodes CR111 to CR114 and A108.[7]
  3. If there is AC at J110 but none across the bridge, switch off and check the switch S102 on the side board and the contacts of J106 pins 1 and 2 between the two boards.[10][2]
  4. With the bridge output low or missing, switch off and test CR111 to CR114 on the diode range, then measure from the bridge output to ground for a short. See Testing Diodes, Transistors and Regulators and Finding Short Circuits.

Check the +5 V rail

[edit | edit source]
  1. Measure pin 3 of A108. Expect 5.0 V.[10]
  2. If it is missing with 11 to 12 V at pin 1, replace A108 (below).[7]
  3. If it is present but low, Sams suspects the error amplifier transistors Q114 and Q115 and checks them by substitution.[7]
  4. With an oscilloscope, look at the ripple at pin 1 of A108, across the filter capacitor C146. Sams' oscillogram shows about 0.8 V peak to peak there with the drive running.[10] See Capacitor Failure Symptoms.

Check the +12 V rail

[edit | edit source]
  1. Measure the output side of Q113 (Sams' J105 pin 2). Expect 12.0 V.[10] Sams calls this the collector of Q113.[7]
  2. If it is missing, measure the doubler output at J105 pin 3. Expect about 25.1 V.[10]
  3. If the doubler output is low or missing, switch off and test CR115 and CR116 on the diode range, and check C148 and C149.[7][12]
  4. If the doubler output is correct and the +12 V is missing or wrong, check the parts around Q113: R149 (1 kΩ), the error amplifiers Q114 and Q115 (MPSA06), R146 (330 Ω), R147 (100 Ω) and R148 (240 Ω), then Q113 itself.[7][2] Sams' schematic gives R148 as 270 Ω, with 240 Ω in some versions.[10]

Check the -5 V rail

[edit | edit source]
  1. Measure the anode of the zener CR107 on the side board. Expect -5.0 V.[7]
  2. If it is missing, check CR107 and the power LED CR108, which are in series with R132 from J106 pin 10.[7][10]
  3. If J106 pin 10 has no negative voltage, check the negative doubler on the rear board: C150, C151, CR117 and CR118.[10][12]

Remove the side and rear boards

[edit | edit source]

Q113 and A108 can only be reached with both boards off the baseplate.[3]

  1. Disconnect the write protect harness (black, green, blank, red, black) and the stepper motor harness (black, white, red, green, brown) from the side board. The plugs are not polarised, so note how each one sits.[15][9]
  2. Remove the three screws holding the side board and its centre ground bracket to the baseplate.[15]
  3. Hold the side board at its front edge and its upper rear corner and lift it straight up to free its rear socket from the pins of the rear board, rocking it slightly if needed.[15]
  4. Disconnect the drive motor connector J103 and the head connector J109 from the rear board.[16]
  5. Remove the four screws holding the rear board to the baseplate.[17]
  6. Hold the rear board by both side edges and lift it straight up until its two right-hand sockets come off the six legs of A108 and Q113, rocking it slightly if needed.[17]

Replace A108 or Q113

[edit | edit source]
Atari 810 Q113 and A108 on the common baseplate (field service manual p. 6-46)
Q113 and A108 on the common baseplate, with the insulating plate under Q113 and the leads bent 90 degrees up (field service manual p. 6-46)

Both devices plug into three-pin sockets (J104 and J105) on the underside of the rear board, so no soldering is needed.[18][2]

  1. Remove the single screw that holds the device to the baseplate and lift it off. Q113 sits on an insulating plate; both devices and the plate are coated with heat transfer compound.[3]
  2. Bend the leads of the new device 90 degrees up, as on the old one.[19]
  3. For Q113, coat both sides of the mica insulating plate with heat transfer compound, place it on the baseplate, set the transistor on it, and fix them with the #4-40 × 3/8 in screw, the shoulder washer, the #4 split-ring lockwasher and the #4 nut.[19]
  4. For A108, coat the back of the regulator with heat transfer compound, place it on the baseplate and fix it with the #4 × 1/4 in thread-forming screw.[20]

Replace parts on the rear board

[edit | edit source]

The bridge diodes, doubler diodes, error amplifiers and filter capacitors are soldered into the rear board. Their positions are on Atari's silkscreen in appendix E of the manual.[21] Use Through-Hole Desoldering and Through-Hole Soldering, and fit electrolytics with the polarity printed on the silkscreen.

Reassembly

[edit | edit source]
  1. Lower the rear board onto the baseplate so that the six legs of A108 and Q113 go into the two three-pin sockets, and fit the four #6-32 × 1/4 in screws with #6 split-ring lockwashers.[18]
  2. Seat the side board's multipin socket on the pins of the rear board and fit the three #6-32 × 5/16 in thread-forming screws through the side board and its ground bracket.[22]
  3. Reconnect the stepper harness to the side board connector marked 2 and the write protect harness to the one marked 1.[22]
  4. Reconnect J103 and J109 on the rear board.[16]
  5. Check that every boss in the base has its rubber washer, refit the coverplate with the baseplate, and fit the five #6 × 1/2 in screws.[23]
  6. Refit the top housing with its four screws and the screw hole covers.[24]

Atari's torque limits are 6 inch-pounds for screws into plastic and 10 inch-pounds for screws into aluminium.[9]

Testing

[edit | edit source]
  1. Switch on and check that the power LED lights and the BUSY light comes on and then goes out.[25]
  2. Measure +5 V, +12 V and -5 V against the table above.
  3. Run Atari's floppy quick-check: boot a master diskette, try to format it write-protected (ERROR-144 must appear), format a scratch diskette and check for 709 free sectors, write and delete files, and load a program from a diskette written on another drive.[25] The steps are on the maintenance guide.
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 Atari, Inc., Atari 810 Disk Drive Field Service Manual (FS015854, Rev. 1, July 1980), p. 2-20, power supply: 9 V AC from the step-down transformer to the PWR jack, the PWR switch, the full-wave bridge, the unregulated 9-10 V DC drive motor supply, regulated +5 V and +12 V, zener-regulated -5 V, and the PWR ON LED lit through the -5 V section. Hosted as File:Atari 810 Disk Drive Field Service Manual FS015854 Rev 1.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Atari, Atari 810 Disk Drive Field Service Manual, parts lists pp. 8-3 to 8-10: final assembly items 37 to 42 (screws 72-1406S and 72-CL404, shoulder washer C014814, insulator C014811, lockwasher, nut); side board CA014162 (CR107 1N5231B C014808-01, R132, power switch S102 C014397-XX); rear board CA014161 (C146, C148, C149 4700 µF 25 V C014780; C150, C151 470 µF 16 V C014368; CR111-CR114 MR501 C014398; CR115-CR118 1N4001; Q114, Q115 MPSA06 C014394; R146, R147, R148, R149; J104, J105 3-pin connectors); A108 voltage regulator C014348.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-13, removing Q113 and A108: both use the common baseplate as a heatsink, Q113 has an insulating plate, and the devices and plate are coated with heat transfer compound.
  4. ↑ 4.0 4.1 Best Electronics, "8-Bit Drives" catalogue page, Atari 810 Tech Tip (retrieved 2026-10-25). Atari parts vendor's service notes.
  5. ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 2 August 2026, mcurrent.name, section 3.2.1: the 810 Analog boards of February 1982. Community reference.
  6. ↑ 6.0 6.1 Sams, Computerfacts CD9, preliminary service checks, p. iii, check 1 (power supply), steps A and B: 10.9 V AC at the power pack; power LED on and drive motor not running.
  7. ↑ 7.00 7.01 7.02 7.03 7.04 7.05 7.06 7.07 7.08 7.09 7.10 7.11 7.12 Howard W. Sams & Co., Computerfacts CD9, Atari Model 810 (June 1986), p. 12, troubleshooting, power supply: 10.9 V AC at the power pack, 12.0 V at the cathode of CR111, 5 V at pin 3 of A108, substitution of Q114 and Q115, 12 V at the collector of Q113, CR115 and CR116, -5 V at the anode of CR107, CR107 and the power LED CR108. Hosted as File:Sams Computerfacts CD9 Atari 810 Disk Drive.pdf.
  8. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 5-3 to 5-7, troubleshooting guide.
  9. ↑ 9.0 9.1 9.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-3, special notes: static-sensitive MOS devices and grounding strap, torque limits of 6 inch-pounds into plastic and 10 inch-pounds into aluminium, non-polarised harness pins and jacks.
  10. ↑ 10.00 10.01 10.02 10.03 10.04 10.05 10.06 10.07 10.08 10.09 10.10 10.11 10.12 10.13 10.14 10.15 10.16 Sams, Computerfacts CD9, schematic, p. 2 (PDF page 3): J110, S102 via P101/J106 pins 1 and 2, CR111-CR114, A108 7805C (11.2 V input), C146, C148, C149, CR115, CR116, Q113 TIP32A (25.1 V input, 12.0 V output), Q114 and Q115 MPSA06, R148 270 (240), the negative doubler C151, CR117, CR118 to P101/J106 pin 10, R132, CR108, CR107 1N5231, and the ripple oscillograms.
  11. ↑ Sams, Computerfacts CD9, p. 13, schematic notes: voltages measured with a digital meter while an Atari 800 runs the BASIC disk test program; values in brackets used in some versions.
  12. ↑ 12.0 12.1 12.2 12.3 Atari, Atari 810 Disk Drive Field Service Manual, appendix D, p. 9-6: schematic of the rear board CA014161 Rev. B.
  13. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-5, disassembling the drive case.
  14. ↑ 14.0 14.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-6 and 6-7, removing the common baseplate.
  15. ↑ 15.0 15.1 15.2 Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-8 and 6-9, removing the side PCB.
  16. ↑ 16.0 16.1 Sams, Computerfacts CD9, p. 13, disassembly instructions, rear (analog) board removal: J103 and J109.
  17. ↑ 17.0 17.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-12, removing the rear PCB.
  18. ↑ 18.0 18.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-48, installing the rear PCB: the six device legs seat in the two three-pin sockets on the board; four #6-32 × 1/4 in screws and lockwashers.
  19. ↑ 19.0 19.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-46, installing Q113: bend the leads 90 degrees up, heat transfer compound on both sides of the mica plate, #4-40 × 3/8 in screw, shoulder washer, #4 lockwasher and nut.
  20. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-47, installing A108 with heat transfer compound and a #4 × 1/4 in thread-forming screw.
  21. ↑ Atari, Atari 810 Disk Drive Field Service Manual, appendix E, p. 9-7: silkscreen of the rear board CA014161 Rev. B. See File:Atari 810 rear board silkscreen (field service manual).png.
  22. ↑ 22.0 22.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-52 and 6-53, installing the side PCB: socket onto the rear board pins, three #6-32 × 5/16 in thread-forming screws, stepper harness to connector 2 and write protect harness to connector 1.
  23. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-54 and 6-55, installing the common baseplate: rubber washers on every boss, the coverplate, five #6 × 1/2 in screws.
  24. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-56, assembling the drive case.
  25. ↑ 25.0 25.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 4-3 to 4-10, floppy quick-check.