Jump to content

Atari 810 Spindle Bearing Replacement

From RetroTechCollection
Atari 810 spindle, bearings, washers and flywheel (field service manual p. 6-19)
The diskette drive spindle, upper spindle shaft bearing, transport casting, flat spacer washers, wavy washer, split-ring lockwashers, flywheel and screw of the MPI transport (field service manual p. 6-19)

The diskette drive spindle of the original Atari 810 with the MPI mechanism runs in two shoulder bearings fitted into a bore in the transport casting, and the belt-driven flywheel is screwed to the bottom of the spindle shaft with a stack of washers.[1][2] Atari's troubleshooting guide lists spindle bearings that are freezing among the causes of a diskette speed that is slow or varies, with the corrective action of replacing the spindle bearings.[3] The number and placement of the washers between the flywheel, casting and spindle helps to determine the diskette speed, so they have to go back exactly as they came out.[4]

The procedure is for the MPI mechanism described in Atari's 1980 field service manual. Drives with the Tandon mechanism of November 1982 use a different transport.[5]

Symptoms

[edit | edit source]
  • The diskette speed is slow or varies. Atari lists freezing spindle bearings as the last of the causes, after the tachometer lead, the write protect circuit, the belt and the drive motor circuit.[3] See Atari 810 Drive Motor Repair for the other checks.

Safety

[edit | edit source]
  • Unplug the transformer before opening the drive.
  • Keep magnetised tools away from the head, and do not lift the pressure pad arm further than the door would lift it.[6][7]

Tools and parts

[edit | edit source]
  • Phillips screwdriver; a small flat tool to ease the top bearing out of the casting.[8]
  • Two spindle shaft shoulder bearings. Atari's parts list gives the transport only as a complete assembly (CA014072) and does not list the bearings, and the manual gives no bearing dimensions. It does warn that a bearing which needs excessive force to go in is probably the wrong one.[9][2]
  • A torque screwdriver able to set 6 inch-pounds for the flywheel screw.[10]
  • For the speed check afterwards, an oscilloscope or a software speed checker.[11]

Procedure

[edit | edit source]

Remove the transport, belt and carrier

[edit | edit source]
Atari 810 drive belt and flywheel (field service manual p. 6-14)
The flywheel and belt on the underside of the MPI transport (field service manual p. 6-14)
  1. Remove the top housing, lift the baseplate out of the base, remove the side board, disconnect the head and drive motor harnesses from the rear board, and take the transport off the baseplate. The steps are in Atari 810 Clutch Cone and Eject Mechanism Adjustment.[4]
  2. Lay the transport on its side and take the belt off by turning the flywheel while easing the belt off its outside edge, so that it is not stretched.[12]
  3. Remove the carrier assembly, as described in Atari 810 Clutch Cone and Eject Mechanism Adjustment.[4]

Remove the flywheel and spindle

[edit | edit source]
  1. Lay the transport on its side. Hold the flywheel with one hand and remove the single screw in its centre.[4]
  2. Hold the spindle with one hand and carefully pull the flywheel away from the casting with the other. Do not lose any of the washers, and note the number and order of the flat spacer washers, the wavy washer and the split-ring lockwashers (see the figure).[4][1]
  3. Pull the spindle out of the casting from the top side.[1]

Replace the bearings

[edit | edit source]
  1. The top bearing may have come out with the spindle. If it did not, prise it out of the casting very carefully.[8]
  2. Push the bottom bearing out of the casting from the top side, taking care not to damage the casting bore.[8]
  3. Gently insert the new top and bottom shoulder bearings into the casting bore. They should be a slight friction fit; if excessive force is needed, the bearing is probably the wrong one, so obtain the correct bearing before going on.[2]
  4. Check that the shoulder of each bearing sits firmly and flat against the casting.[2]

Refit the spindle and flywheel

[edit | edit source]
  1. Lay the casting on its side and insert the diskette drive spindle into the bearings from the top side of the casting.[13]
  2. Assemble the same combination of washers that came off, in the same order, with the flywheel and its screw.[13]
  3. From the bottom side of the casting, place the flywheel, screw and washers over the bottom of the spindle shaft, screw them together and tighten the screw to 6 inch-pounds.[10]
  4. Turn the flywheel and check for wobble, runout or binding of the flywheel or the spindle, and correct the assembly if needed.[10]

Reassembly

[edit | edit source]
  1. Refit the carrier assembly and set the clutch cone clearance and eject latch, as described in Atari 810 Clutch Cone and Eject Mechanism Adjustment.[10]
  2. Refit the belt and adjust its tension; see Atari 810 Drive Motor Repair.[14]
  3. Refit the transport to the baseplate, reconnect the harnesses, refit the side board and the baseplate, and leave the top housing off for the speed adjustment.[15][16]

Testing

[edit | edit source]
  1. Check the speed and set it with R142 if needed: Atari measures the tachometer frequency at the anode of CR110 with the drive reading any track. The values for each belt and motor pulley are in Atari 810 Drive Motor Repair.[11]
  2. Refit the top housing and run Atari's floppy quick-check, including loading a program from a diskette written on another drive.[17][18]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.0 1.1 1.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-19, removing the flywheel and spindle, steps 8 and 9, with the exploded view of the spindle, bearing, washers and flywheel.
  2. ↑ 2.0 2.1 2.2 2.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-36, installing the transport spindle shaft bearings.
  3. ↑ 3.0 3.1 Atari, Inc., Atari 810 Disk Drive Field Service Manual (FS015854, Rev. 1, July 1980), p. 5-4, troubleshooting guide: diskette speed slow or varying, causes A to F (tachometer lead, write protect circuit, belt tension, stretched belt, drive motor circuit, spindle bearings freezing), replace spindle bearings. Hosted as File:Atari 810 Disk Drive Field Service Manual FS015854 Rev 1.pdf.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-18, removing the transport flywheel and drive spindle, steps 1 to 7, and the note that the number and placement of the washers helps to determine diskette speed.
  5. ↑ Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, last modified 2 August 2026, mcurrent.name, section 3.2.1: the Tandon mechanism from November 1982. Community reference.
  6. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-31, cautions on the head.
  7. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-17, caution about lifting the pressure pad arm.
  8. ↑ 8.0 8.1 8.2 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-20, removing the transport spindle shaft bearings.
  9. ↑ Atari, Atari 810 Disk Drive Field Service Manual, parts lists pp. 8-3 to 8-5: the disk drive (transport) CA014072, with no separate bearing listing.
  10. ↑ 10.0 10.1 10.2 10.3 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-38, installing the flywheel and spindle, steps 4 to 6: 6 inch-pound torque, checking for wobble, runout and binding, refitting the carrier assembly.
  11. ↑ 11.0 11.1 Atari, Atari 810 Disk Drive Field Service Manual, pp. 7-9 and 7-10, speed adjustment at the anode of CR110 with R142.
  12. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-14, removing the transport drive belt.
  13. ↑ 13.0 13.1 Atari, Atari 810 Disk Drive Field Service Manual, p. 6-37, installing the transport flywheel and drive spindle, steps 1 to 3.
  14. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-43, step 20: install the drive belt if necessary.
  15. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 6-49 and 6-50, installing the drive transport and reconnecting its harnesses.
  16. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-55: after reassembly, the head cleaning, radial alignment, speed and track 00 adjustments.
  17. ↑ Atari, Atari 810 Disk Drive Field Service Manual, p. 6-56, assembling the drive case.
  18. ↑ Atari, Atari 810 Disk Drive Field Service Manual, pp. 4-3 to 4-10, floppy quick-check.