Jump to content

Atari 820 Print Head Driver Repair

From RetroTechCollection
Atari 820 print head solenoid drivers (field service manual appendix A)
The head driver section of Atari's 820 schematic: each solenoid sits between +40 V and a TIP122 (Q104 to Q110) on connector J102, driven from a 3086 array transistor through a 4.7 µF capacitor

The Atari 820 prints each character as a 5 × 7 dot matrix with a print head of seven solenoids stacked in a vertical bar: the top hammer is solenoid 1 and the lowest is solenoid 7.[1] Each solenoid needs a pulse of about 3.0 to 3.6 A, which a driver transistor sinks to ground from the unregulated +40 V supply.[1] A dot that is always missing from the same row of every character points to one solenoid, its wiring or its driver; Atari's troubleshooting guide lists the 6532 PIA, the transistor arrays, the drivers and the print head as the causes, in that order.[1] The schematic lets each channel be followed from the PIA to the head.

Symptoms

[edit | edit source]
  • The same dot is missing from every character (the same row of the 5 × 7 matrix). Count from the top: the top row is solenoid 1.[1]
  • Atari's Printer Quick Check program includes a check for missing dots.[1]

If the head moves but nothing prints at all, the +40 V supply or its fuse is more likely than seven drivers at once; Atari's guide lists a blown fuse, a broken fuse holder, the transformer and the main board for that symptom. The supply is covered in the Atari 820 Troubleshooting guide.[1]

Safety

[edit | edit source]

The 820 runs from 120 V AC, and mains is present at the power cord, the fuse holders, the switch, the transformer and the AC motor. The head supply is +40 V. Atari's manual notes that skin resistance is normally about 300 Ω, so any voltage above 30 V can be lethal. Unplug the printer before changing any part, and never change a chip with the power on or the printer plugged in.[1]

The chips are MOS devices; use an earthed mat and a wrist strap.[1]

How the drive works

[edit | edit source]

The seven head lines leave the 6532 PIA (A103) on port A, PA1 to PA7 (pins 9 to 15), with small 0.001 µF capacitors (C113 to C119) on the lines. Each line then passes a 4.7 µF capacitor (C120 to C126) to one transistor of a 3086 array, which drives a TIP122 Darlington through a 100 Ω resistor. The TIP122's collector goes to one pin of J102; the other end of the solenoid is on +40 V through the matching pin on the other side of the connector.[1]

820 head channels (FD100048 appendices A and C)
Solenoid (dot row) J102 pins TIP122 driver 3086 section Input capacitor
1 (top) 1, 8 Q104 A105C C120
2 2, 9 Q105 A105D C121
3 3, 10 Q106 A107A C122
4 4, 11 Q107 A107B C123
5 5, 12 Q108 A107C C124
6 6, 13 Q109 A107D C125
7 (bottom) 7, 14 Q110 A107E C126

On the schematic, pins 8 to 14 are the +40 V side and pins 1 to 7 the driver side.[1]

Tools and parts

[edit | edit source]
  • A multimeter and an oscilloscope.
  • A driver to fit the 3/16 in hex head screws on the guide bar, a feeler gauge for the head gap, and IBM #23 or Lubriplate #70 grease.[1]
Parts in the head drive (FD100048 parts list)
Location Part Atari part number
A103 6532 PIA C010750
A104, A105, A107 3086 transistor array (socketed) C010174
Q104-Q110 TIP122 transistor (939M) C014350
C120-C126 4.7 µF 16 V electrolytic, radial C014369
CR101-CR108 1N914 diode 31-1N914
– Print head C016732-001
F101, F102 Fuse, 2 A type 3AG 46-2032002

[1]

Procedure

[edit | edit source]

Confirm which solenoid

[edit | edit source]
  1. Run the operator test: switch on and press the paper advance button. With the top housing off, press paper advance and check that the print wires of all seven solenoids move and return to rest.[1]
  2. Run the Printer Quick Check program from a 400 or 800 and note which row is missing.[1]
  3. Find the solenoid, J102 pins, driver and array section for that row in the table above.

Open the printer

[edit | edit source]
  1. Make sure the print head is at home at the left; if not, turn the drive cam towards the platen until it is.[1]
  2. Turn the printer over, remove the four black feet and the four case screws under them, turn it back over and lift off the top housing cover, the paper roll and mandrel, then the top housing.[1]
  3. To reach the chips, straighten the five tabs of the noise shield over them and lift it off.[1]
Atari 820 print head harness connector pins (field service manual appendix C)
Atari's appendix C: the head harness connector seen from the board side, with the pin pair for each solenoid

Check the head and harness

[edit | edit source]
  1. Unplug the printer and disconnect the head harness from J102.[1]
  2. Measure the resistance between the two pins of the suspect solenoid on the harness plug (for example pins 1 and 8 for solenoid 1) and compare it with the other six. An open reading means a broken coil or a broken harness wire. See Continuity Testing and Signal Tracing.[1]
  3. Inspect the connector and its pins for open or partial contacts; Atari's guide starts every repair with this check.[1]

Check the driver

[edit | edit source]
  1. Reconnect the head and run the Quick Check program. With an oscilloscope, look at the collector of the suspect TIP122 (the J102 driver-side pin for that solenoid). It should pull low in short pulses as the dots fire. Atari gives about 1.3 ms from dot to dot on a 40-column line.[1]
  2. If the collector does not pulse, look at the base of the TIP122 and the output of its 3086 section. Pulses at the base but none at the collector point to the TIP122; no pulses there point back to the 3086 array or the PIA line. See Testing Diodes, Transistors and Regulators and Logic Chip Testing.[1]
  3. The chips are socketed. Atari's order for substitution is the PIA (A103), the MPU (A102), the ROM (A101), then the 3086 arrays (A104, A105, A107). Retest after each change and leave substituted chips in place until all the suspects have been tried.[1]
  4. A failed TIP122 is soldered to the board: see Through-Hole Desoldering and Through-Hole Soldering. Atari's own remedy for a driver fault was to replace the main board.[1]

Replacing the print head

[edit | edit source]

If the coil is open or the head is worn, Atari's procedure:[1]

  1. Disconnect the print head harness from J102 on the main board.
  2. Trace the harness back to its clamp on the side plate and remove the screw holding it.
  3. Remove the two hex head screws holding the print head guide bar to the side plates.
  4. Lift the head and guide bar away, easing the head's tailpiece out of its guide slot.
  5. Grease the head's inner sliding bushings, the tailpiece and its guide slot, and the elliptical groove in the drive cam.
  6. Slide the head onto the guide bar; it must move freely.
  7. Lower the head and guide bar into place with the tailpiece in its slot and the metal stub under the head in the slot of the drive cam.
  8. Fit the two guide bar screws without tightening them.
  9. With the paper and ribbon removed, set the gap between head and platen to 0.012 to 0.015 in with a feeler gauge, moving the head across the platen to check that it stays within that range. Turn the drive cam only towards the platen; turning it the other way can damage the Print OK switch. Tighten the hex head screws.
  10. Refit the harness clamp to the head harness and the side plate, and reconnect J102.

Testing

[edit | edit source]
  1. Run the operator test and check that all seven print wires move.[1]
  2. Run the Printer Quick Check program and check the printout for missing dots, even repeated characters and straight columns.[1]
  3. Do not run the printer without a ribbon and paper fitted; it can damage the print head solenoids.[2]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 Atari, Inc., ATARI 820 Printer Field Service Manual, FD100048, July 1981: safety p. 1-5 (PDF p. 15); print head mechanism p. 4-3, amplifier/driver interface and current waveform pp. 4-9 and 4-10 (PDF pp. 31, 37 and 38); system static-free work station, maintenance section (PDF p. 45); check-out, Printer Quick Check program and troubleshooting procedure pp. 5-4 to 5-10, table 5-1 pp. 5-11 and 5-12 (PDF pp. 48-58); chip replacement p. 5-13 (PDF p. 59); top housing disassembly p. 5-23 (PDF p. 69); print head replacement and alignment pp. 5-15 to 5-17 (PDF pp. 61-63); appendix A, schematic (PDF p. 79); appendix C, harness connectors (PDF p. 83); parts list (PDF pp. 89-92). Hosted here as File:Atari 820 Printer Field Service Manual FD100048.pdf.
  2. ↑ Atari, Inc., 820 Printer Operators Manual (C014762, 1979), setting up. Hosted here as File:Atari 820 Printer Operator's Manual C014762.pdf.