Jump to content

Atari 1050 Power Supply Repair

From RetroTechCollection
Atari 1050 main board
Atari 1050 main board out of the case. The three large filter capacitors of the power supply are on the right; the RF shield covers the large chips

The Atari 1050 has no internal transformer. An external adaptor supplies about 9 V AC, and the main board rectifies it and makes two regulated rails: +5 V from regulator Q7 for the logic and the floppy disk controller, and +12 V from regulator Q8, fed by a voltage doubler, for the stepper motor, the spindle motor, the read/write and erase circuits and the tachometer feedback.[1] When the power LED stays dark, or the LED lights but the motors never move, the fault is usually in this chain or in the adaptor. Atari's symptom checklist names the bridge diodes, the adaptor, Q7, Q8, the LED, and the doubler parts CR15, CR16 and C71.[1] Work along the supply from the adaptor plug to the test points, comparing each stage with Atari's waveforms and with the voltages Howard W. Sams measured on a working drive.[2]

Atari's manual describes the drive built with the Tandon TM50-1 mechanism; its parts list and schematics are headed "Tandon".[1]

Symptoms

[edit | edit source]
  • The power LED does not light and nothing happens at switch-on. Atari lists defective bridge diodes, a defective adaptor and the 5 V regulator Q7 for this.[1]
  • The drive "blows power": Atari's remedy is to replace all four bridge diodes, CR17 to CR20.[1]
  • The power LED lights, but the spindle motor does not run and the head does not step. With no +12 V at TP14, Atari points to Q8 or the doubler.[1]
  • The drive died after it was plugged into a DC adaptor. An Indus GT supply is DC, and plugged into a 1050 it usually blows the rectifier diodes.[3]

A drive whose LEDs light and whose spindle motor cycles off and on every 2 seconds has failed its own power-up self test; that is a logic or track 00 fault, covered in the Atari 1050 Drive Troubleshooting guide.[1]

Safety

[edit | edit source]

The adaptor contains a mains transformer. Unplug it from the wall before opening it; its primary connections carry mains voltage.[4] The drive's own board runs only from the adaptor's low-voltage AC output.[1]

Tools and parts

[edit | edit source]
  • A digital multimeter with AC and DC ranges. Atari's field kit also lists a 15 MHz oscilloscope, which is needed to compare the rectifier waveforms with the manual.[1]
  • For the adaptor: Atari's 9 V AC, 31 VA adaptor C017945 (rated 3.4 A) in North America; the UK adaptor CO60592-34 is 9 V AC, 3.4 A, 27 VA.[3] Atari's specification for the drive's input is 8.52 V AC ±12 %.[1]
  • Replacement parts as found. Atari's parts list gives the bridge diodes CR17 to CR20 as MR501, part number C014398; its schematic shows a 7805 at Q7, a 7812 at Q8, 1N4001 diodes at CR15 and CR16, and 4,700 µF 35 V capacitors at C67, C68 and C71.[1] The Sams sample used BY251 rectifiers, 1N5392 doubler diodes, a µA7805, an L7812CV and 6,800 µF capacitors at C68 and C71, with 4,700 µF noted as the value used in some versions.[2] Values for every electrolytic are in the Atari 1050 Capacitor Replacement Guide.
  • Igor Gramblicka has replaced the linear regulators with drop-in switching modules to cut the heat they make: a RECOM or TRACO module in place of the 7805, and for the XF551 the TRACO TSR 1-2450 for the 7805 and TSR 1-24120 for the 7812, which he says can be used the same way in the 1050.[5]
Atari 1050 power supply schematic (field service manual sheet 4)
The power supply on Atari's schematic sheet 4: power jack J13 and switch S1, bridge CR17-CR20, Q7 (7805) for +5 V at TP13, and the doubler CR15, CR16 and C71 feeding Q8 (7812) for +12 V at TP14

How the supply works

[edit | edit source]

The power switch S1 feeds the adaptor's AC to the bridge rectifier, CR17 to CR20. The bridge output, smoothed by C67, feeds Q7, whose output is +5 V at TP13; the power LED CR21 is fed from +5 V through R70 (180 ohms). C71 couples the AC side of the bridge to the junction of CR15 and CR16, and the doubled voltage, smoothed by C68, feeds Q8, whose output is +12 V at TP14. TP15 is ground.[1]

Procedure

[edit | edit source]

Check the adaptor

[edit | edit source]
  1. Unplug the adaptor from the drive and measure its output across the plug on the AC range. Sams measured 10.9 V AC with the adaptor unloaded; its preliminary checks use a round 10 V AC. If the voltage is missing, replace or repair the adaptor.[6][7]
  2. Atari's manual, which describes the 120 V adaptor, gives it an internal 2 A fuse.[1] One drive that would not switch on had no fuse at all inside its adaptor.[8]
  3. To open a European 230 V adaptor, Amedeo Valoroso removed the four slotted screws in the lower half of the case; the transformer inside is held by four screws, and the fuse holder is fixed to tabs on the transformer bobbin.[4]
  4. Valoroso's adaptor gave 3.4 V AC instead of 9 V or more. He resoldered every winding connection, scraping the insulating enamel off the secondary winding wire before soldering it, and the output came back.[4]
  5. To test an adaptor under load he connected a 4.7 ohm resistor across the secondary, which draws about 2 A and must be rated for about 10 W, and checked that the voltage held.[4]

Open the drive

[edit | edit source]
  1. Unplug the adaptor and the SIO cables.[1]
  2. Turn the drive over and remove the four screws from the bottom cover and the two screws holding the lower part of the front bezel.[1]
  3. Hold the covers together, turn the drive the right way up, pull the lower part of the bezel forward and lift off the top cover. Do not break the thin plastic tabs joining the top of the bezel to the top cover.[1]
  4. The mechanism rests on four dowels above the board. To remove it, disconnect its plugs from the board and lift it out. Refit the plugs by the wire colours in figure 3-1 of the manual; pin 1 is marked on the board.[1]
Atari 1050 disassembly (field service manual figure 3-2)
Atari's figure 3-2: top cover, drive mechanism, main board, bottom cover and front bezel
Atari 1050 main board silkscreen (field service manual, redrawn)
Atari's silkscreen of the main board (redrawn copy), for finding Q7, Q8, CR15 to CR21 and the test points
Atari 1050 main board component locations (Sams Computerfacts CD13)
Sams photograph of the main board with the leads of Q7 (top left) and Q8 and Q6 (bottom edge) marked

Trace the supply

[edit | edit source]

Work from the input towards the test points and stop at the first stage that is wrong; see Continuity Testing and Signal Tracing for the general method. Sams took its readings from ground with the drive writing to a disk; Atari's waveforms were drawn on 60 Hz mains, with a 16.6 ms period.[9][10]

Atari 1050 power supply checkpoints
Stage Where to measure Expected If wrong
Bridge output Cathodes of CR17 and CR18 About 11.1 V DC (Sams); 12 V with an 8.3 ms ripple at the cathode of CR18 (Atari) Check J13, S1 and CR17 to CR20[6][10]
Bridge AC inputs Cathodes of CR20 and CR19 Half-wave pulses of about 13 V and 11 V peak, 16.6 ms apart, dipping to about -1 V Compare with figure 4-16[10]
5 V regulator input Q7 pin 1 9.8 V Bridge, C67[2]
+5 V TP13 +5 V DC Replace Q7[10][1]
Power LED Anode of CR21 1.7 V DC LED not lit with +5 V present: replace CR21[10][1]
Doubler Cathode of CR15 Pulses between about 12 V and 25 V CR15, C71[10]
12 V regulator input Cathode of CR16 (Q8 pin 1) 24 V with a 16.6 ms ripple (Atari); 17.8 V on the Sams schematic and 22.4 V in the Sams text Replace CR15 and CR16 or C71 (Atari); check CR15, CR16, C66 and C68 (Sams)[10][2][6]
+12 V TP14 +12 V DC Input present: replace Q8; Sams also checks C70 and C65[1][6]
Atari 1050 power supply signals (field service manual page 4-16)
Atari's power supply waveforms, page 4-16
Atari 1050 power supply voltages (Sams Computerfacts CD13 schematic)
The same circuit on the Sams schematic, with the measured voltages
  1. Switch on with the adaptor connected. Measure the bridge output at the cathodes of CR17 and CR18. If the 11.1 V is missing, check the power jack J13, the switch S1 and the diodes CR17 to CR20.[6] If any bridge diode has failed, replace all four.[1] See Testing Diodes, Transistors and Regulators for checking the diodes out of circuit.
  2. Measure TP13. If +5 V is missing while Q7's input is present, replace Q7.[1][6]
  3. If +5 V is present but the power LED is dark, check for 1.7 V at the anode of CR21 and replace the LED if the voltage is there.[10][1]
  4. Measure TP14. If +12 V is missing, measure Q8 pin 1. Sams gives 22.4 V here in its troubleshooting text and 17.8 V on its schematic; Atari's waveform shows 24 V at the cathode of CR16. Either way, a reading near zero means the doubler: CR15, CR16, C71 (Atari), or CR15, CR16, C66 and C68 (Sams).[6][2][10][1]
  5. If Q8's input is present and TP14 is not at +12 V, replace Q8, and check C70 and C65.[1][6]

Replace the failed part

[edit | edit source]
  1. Remove the failed part with a desoldering pump or braid; see Through-Hole Desoldering. Use the silkscreen and the Sams photograph to find it on the board.[1][2]
  2. Fit the new part the same way round. The bridge diodes, CR15 and CR16 are polarised, and so are C67, C68, C69, C70 and C71.[1] See Through-Hole Soldering and Capacitor Replacement Procedure.
  3. Gramblicka notes that the regulators share the drive's large heatsink with the spindle motor's power transistor, and that anything taken off the heatsink must still be cooled.[5] Mount a new regulator to the heatsink in the same way as the old one.
  4. If you convert the drive to run from a DC supply, as in Gramblicka's modifications, fit a different power connector so that the original AC adaptor cannot be plugged in by mistake.[5]

Testing

[edit | edit source]
  1. Check TP13 for +5 V, TP14 for +12 V and the anode of CR21 for 1.7 V, with TP15 as ground.[10]
  2. Switch on with no diskette. The power LED and the activity LED light, the spindle motor starts, the head steps to track 0, and after several seconds the motor and the activity LED switch off. This is the drive's power-up self test passing.[1]
  3. Run the automatic tests on Atari's 1050 diagnostic diskette (FD100690), described in the Atari 1050 Maintenance Guide.[1]

Board and part differences

[edit | edit source]

Atari's parts list and schematics in the hosted manual are for the Tandon-mechanism drive; the manual's contents list no other parts list.[1] Best Electronics sells a separate drive belt for the World Storage mechanism fitted to drives assembled in Hong Kong (CB101149).[11] The Sams sample used different parts at several positions of the supply, listed under Tools and parts.[2]

[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 Atari, Inc., 1050 Disk Drive Field Service Manual (FD100330). Power supply p. 1-8 (PDF p. 14); test equipment p. 2-1 and power-up test pp. 2-2 and 2-3 (PDF pp. 29-31); disassembly and figure 3-1 pp. 3-1 and 3-2 (PDF pp. 41-42); power supply problems p. 4-5 (PDF p. 47); parts list p. 5-11 (PDF p. 62); schematic sheet 4 of 4 (PDF p. 66, redrawn copy PDF p. 71); appendix 6A input specification p. 6A-3 (PDF p. 75). Hosted here as File:Atari 1050 Disk Drive Field Service Manual.pdf.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Howard W. Sams & Co., Computerfacts CD13, Atari Model 1050 Disk Drive (1987), schematic (PDF p. 3, printed p. 2): power supply part types and the voltages at Q7 and Q8; CircuiTrace photograph of the main board (PDF p. 13, printed pp. 3 and 14). Hosted here as File:Sams Computerfacts CD13 Atari 1050 Disk Drive.pdf.
  3. ↑ 3.0 3.1 Michael D. Current (ed.), Atari 8-Bit Computers: Frequently Asked Questions, version last modified 29 November 2009, section 6.7, power requirements: adaptors C017945 and CO60592-34, and Paul Alhart's note on mixing up Indus GT and 1050 supplies. faqs.org. Community reference.
  4. ↑ 4.0 4.1 4.2 4.3 Amedeo Valoroso, "Atari 1050 floppy disk drive: power supply repair and test!", valoroso.it, 25 June 2021. Opening and repairing a 230 V 1050 adaptor, and testing it under load. Repair write-up.
  5. ↑ 5.0 5.1 5.2 Igor Gramblicka, "ATARI 1050, ATARI XF551 - napájací zdroj, Power Supply ATARI 1050, ATARI XF551 - modification", Igi blog, updated 19 January 2014 and 29 June 2015 (in Slovak). The original 7805 and 7812 supply, its heat losses, drop-in switching regulators, the shared heatsink and the advice to change the connector on DC conversions.
  6. ↑ 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 Howard W. Sams & Co., Computerfacts CD13 (1987), p. 6, Troubleshooting, "Power supply" (10.9 V AC at the adaptor plug, 11.1 V at the cathodes of CR17 and CR18, 22.4 V at pin 1 of Q8, the parts to check at each stage).
  7. ↑ Howard W. Sams & Co., Computerfacts CD13 (1987), Preliminary Service Checks (PDF p. 18), power supply check (A): 10 V AC at the output of the power pack.
  8. ↑ xAD / nIGHTFALL, "Atari 1050 Disk Drive Repair", nIGHTFALL Blog, 23 February 2022. A drive that did not switch on because the fuse inside its adaptor was missing. Repair log.
  9. ↑ Howard W. Sams & Co., Computerfacts CD13 (1987), p. 11, schematic notes: voltages and waveforms taken from ground with an Atari 800 running a BASIC program that writes a file to the drive repeatedly.
  10. ↑ 10.00 10.01 10.02 10.03 10.04 10.05 10.06 10.07 10.08 10.09 Atari, 1050 Disk Drive Field Service Manual (FD100330), p. 4-16 (PDF p. 58), power supply signals: waveforms at the cathodes of CR20, CR19, CR18, CR15 and CR16, anode of CR21 1.7 V DC, TP13 +5 V, TP14 +12 V, TP15 ground.
  11. ↑ Best Electronics, "8-Bit Drives" catalogue page: drive belt for the World Storage mechanism in Hong Kong-built 1050s, CB101149. Retrieved 25 October 2026.