Atari 1050 Spindle Motor Control Repair

The spindle motor of the Atari 1050 is a DC motor with a built-in tachometer, and it turns the diskette through a belt and a flywheel. The motor control circuit on the main board switches it on when the drive needs the disk turning, and a tachometer feedback loop holds it at 288 rpm, one revolution in 208.3 ms. The activity LED lights whenever the motor is on.[1] When the disk does not turn, turns erratically, or will not hold its speed, Atari's checklist points at the diskette enable switch and its circuit (U6), the motor control parts Q4, Q6, U5 and VR2, the tachometer winding, the belt and the motor itself.[2] The checks below follow that path with Atari's waveforms and the voltages Howard W. Sams measured on a working drive.[3][4]
Atari's manual describes the drive built with the Tandon TM50-1 mechanism.[1]
Symptoms
[edit | edit source]- The motor does not turn when the latch is shut, and the activity LED stays dark.[2]
- The motor runs only now and then.[2]
- The speed is too slow or too fast, will not adjust, or will not stay steady.[2]
- The motor runs all the time, with or without a diskette. On one drive the cause was a failed 6532 RIOT (U7).[5]
A drive whose spindle motor cycles off and on every 2 seconds after switch-on has failed its own power-up self test, which checks the 6532, the 2793 controller, the ROM checksum and the RAM, and seeks track 0; the Atari 1050 Drive Troubleshooting guide covers it.[1] A drive with no power LED has a supply fault; see Atari 1050 Power Supply Repair.
Tools and parts
[edit | edit source]- A multimeter, an oscilloscope (Atari specifies at least 15 MHz) and Atari's 1050 diagnostic diskette FD100690 for setting the speed.[1]
- Replacement parts as found. Atari part numbers: spindle motor FC100520; diskette enable ("ready") switch assembly FA100519; Q6 TIP110, FC100529; Q4 2N4124, FC100527; U5 LM2917, C017101; VR2 2k cermet trimmer, FC100525; U6 74LS00, C014341; U7 6532 PIA, C010750.[6] The Sams sample had a CS2719 at U5.[4]
- Best Electronics lists drive belts for the Tandon mechanism used in Singapore-built drives (CB101140) and for the World Storage mechanism used in Hong Kong-built drives (CB101149), and a complete Tandon mechanism (CB101147).[7]

How the circuit works
[edit | edit source]The PIA (U7) controls the motor from pin 11, the MOTOR CONTROL line, which reaches the base of Q4 through R63 (4.7k). With pin 11 high (3.2 V), Q4 conducts and its collector sits near 0 V, holding Q6 off; with pin 11 low, Q4 turns off and Q6 (a TIP110 fed from +12 V through L6) powers the motor through J1 pin 1 (red). The motor returns on J1 pin 2 (blue) through R80 (1 ohm). The activity LED on J12 is fed from Q6's emitter through R79 (360 ohms).[8][3][4]
The tachometer signal comes back on J1 pins 3 and 4 to U5, an LM2917 frequency-to-voltage converter: pin 3 (grey) reaches U5 pin 11 through R69 (20k), and pin 4 (yellow) goes to U5 pin 1. VR2 sets the voltage on U5 pin 10; turning it changes the frequency on the motor control lines, U5 pin 8 and pins 11 and 5.[8][9]
The diskette enable switch on the mechanism reaches the board on J14 and sets or clears a latch made from two gates of U6, whose output is the READY line to the floppy disk controller.[8][4]
Procedure
[edit | edit source]Open the drive and check the mechanics
[edit | edit source]- Open the drive and lift out the mechanism as described in Atari 1050 Power Supply Repair#Open the drive.[1]
- Check that the diskette enable lever moves freely and locks in the perpendicular position, that a diskette pushed fully in makes the eject mechanism click into place, and that the diskette is ejected when the lever is returned to the parallel position.[1]
- Look at the drive belt on the underside of the mechanism, between the motor pulley and the flywheel (figure 2-2). Sams's first check when the motor does not turn the disk is the belt, and a slipping belt is to be replaced.[1][10] See Drive Belt Replacement for the general method.
- Sams also checks the pressure cone for broken tabs when disk operation is erratic.[10] For a slipping belt or wrong cone pressure, Atari's own remedy is a new drive mechanism.[2]
- Refit the mechanism and reconnect its plugs by the wire colours in figure 3-1 before taking any of the live measurements below.[1]
- U7, the 6532, sits under the RF shield with the other LSI chips. To reach its pin 11, bend up the four tabs that hold the top shield to the board and lift it off, noting where its cutouts are so that it goes back the same way.[1]

Check the motor and tachometer
[edit | edit source]- Unplug P1 from J1. Measure about 11 ohms across pins 1 and 2 (the motor) and about 186 ohms across pins 3 and 4 (the tachometer). Other readings mean a new motor.[11]
- Refit the plug by its wire colours: Atari's figure 3-1 gives J1 as red, blue, white and yellow from pin 1, and its schematic labels pin 4 yellow (+ tach) and pin 3 grey (- tach).[1][8] Check the plug is fully home; Atari's first remedy for a motor that runs only now and then is the P1 to J1 connection.[2]
- With the drive on and the motor commanded to run, Sams expects about 10 V at P1 pin 1 (red lead). If it is there and the motor does not turn, try another motor.[10]
Check the diskette enable circuit
[edit | edit source]
- Measure U6 with the lever closed (diskette enabled) and open. Atari gives: enabled, pin 10 at 0 V, pin 12 at 5 V and pin 8 at 4.5 V; disabled, pin 10 at 5 V, pin 12 at 0 V and pin 8 at 0 V.[12]
- If pins 10 and 12 do not change when the lever moves, check the switch and its plug J14 (white, black and blue from pin 1); Atari replaces the switch assembly on the mechanism.[1][2][11] See Switch and Potentiometer Repair.
- If the inputs change but pin 8 does not, U6 is suspect.[2] See Logic Chip Testing.
Follow the motor control signal
[edit | edit source]

Atari's waveforms show each point with the motor off and on; Sams's readings were taken while the drive was writing a file over and over.[3][13]
| Point | Motor off (Atari) | Motor on (Atari) | Running (Sams) |
|---|---|---|---|
| U7 pin 11 | 3.2 V | 0 V | 0.1 V |
| Q4 base | 0.75 V | 0.1 V | 0.2 V |
| Q4 collector | 0.15 V | About 8 V, with ripple | 7.9 V |
| Q6 emitter | 0 V | About 8 V, with ripple | 7.0 V |
| J12 pin 1 (activity LED) | 0 V | 1.7 V | – |
| Q6 collector | 12 V | 12 V | 12.0 V |
- Check for 12 V at the collector of Q6, constant whether the motor is on or off. If it is missing, check the +12 V supply first.[3]
- Insert a diskette and turn the enable lever down; the activity LED lights and the motor spins for about five seconds.[1] While it does, pin 11 of U7 should fall from 3.2 V to about 0 V. If it does not change, substitute U7.[3][11] A motor that never stops can also be U7: on one drive replacing the RIOT cured a motor that ran all the time.[5]
- Work along the table. The fault lies between the last point that matches and the first that does not: R63 and Q4 between U7 and Q4's collector, Q6 between its base and emitter, and J1, its plug, the motor or the return resistor R80 beyond Q6's emitter.[3][8] See Continuity Testing and Signal Tracing and Testing Diodes, Transistors and Regulators.
- If the emitter of Q6 is at about 8 V and the activity LED lights but the disk does not turn, go back to the belt and the motor checks.[3][10]
Check the speed loop
[edit | edit source]
- Measure U5 pin 9: Atari gives a constant 8 V; Sams measured 7.7 V with the drive running.[9][4]
- With the motor running, look at U5 pin 11 on the oscilloscope. Atari shows pulses swinging from about 4.8 V down to -0.8 V, against 0.2 V with the motor stopped. No pulses with the motor turning means the tachometer winding (186 ohms across J1 pins 3 and 4), its plug, or R69.[9][11][8]
- U5 pin 5 should show a rippled level of about 1.8 V with the motor running.[9] Sams measured 1.1 V at pin 11, 1.7 V at pin 5, 4.0 V at pin 10 and 9.9 V at pin 8 with the drive writing.[4]
- Turn VR2 slowly and watch pin 10. If its voltage does not move, suspect VR2; if it moves but the speed does not change, suspect U5 and Q6. Atari lists VR2, U5, Q6 and an open tachometer winding for a speed that will not adjust.[9][2]
Replace the failed part and set the speed
[edit | edit source]- Replace the part with a part of the same type; see Through-Hole Desoldering and Through-Hole Soldering. Keep Q6 mounted on its heatsink as the original was.[14]
- Set the speed with VR2 to 208.3 ms ±1.0 ms using option 1 of the diagnostic diskette, loop on speed calibration. The full procedure is in the Atari 1050 Maintenance Guide.[1] Sams's preliminary checks say to set VR2 for 300 rpm; Atari's figure for the 1050 is 288 rpm (208.3 ms).[10][1]
Testing
[edit | edit source]- Switch on with no diskette. The activity LED lights, the motor starts, and after several seconds the motor and the LED switch off.[1]
- Run the automatic tests on the diagnostic diskette. The motor start test times the motor from a dead start to valid data, and the motor speed test reports the speed in milliseconds; both must pass.[1]
Related pages
[edit | edit source]- Atari 1050
- Atari 1050 Drive Troubleshooting
- Atari 1050 Maintenance Guide
- Atari 1050 Power Supply Repair
- Atari 1050 Capacitor Replacement Guide
- Atari 1050 Head Stepper and Track 00 Sensor Repair
- Atari 1050 SIO Port Repair
- Atari 1050 Documentation
- Floppy Drive Repair
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 Atari, Inc., 1050 Disk Drive Field Service Manual (FD100330). Mechanical theory pp. 1-6 and 1-7 (PDF pp. 12-13); test equipment, mechanical checks, power-up test and diagnostic tests pp. 2-1 to 2-4 (PDF pp. 29-32); figure 2-2 p. 2-7 (PDF p. 35); disassembly, RF shields and figure 3-1 pp. 3-1 and 3-2 (PDF pp. 41-42); appendix 6A (PDF p. 74). Hosted here as File:Atari 1050 Disk Drive Field Service Manual.pdf.
- ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Atari, 1050 Disk Drive Field Service Manual (FD100330), symptom checklist pp. 4-1 and 4-2 (PDF pp. 43-44), drive motor and speed problems, including the drive belt and cone pressure.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Atari, 1050 Disk Drive Field Service Manual (FD100330), p. 4-8 (PDF p. 50), motor control signals: U7 pin 11, base and collector of Q4, emitter of Q6, J12 pin 1, and the constant 12 V at the collector of Q6.
- ↑ 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Howard W. Sams & Co., Computerfacts CD13, Atari Model 1050 Disk Drive (1987), schematic (PDF p. 3, printed p. 2): motor control circuit with CS2719 at U5 and measured voltages. Hosted here as File:Sams Computerfacts CD13 Atari 1050 Disk Drive.pdf.
- ↑ 5.0 5.1 xAD / nIGHTFALL, "Atari 1050 Disk Drive Repair", nIGHTFALL Blog, 23 February 2022. A drive whose motor ran all the time, cured by replacing the 6532 RIOT. Repair log.
- ↑ Atari, 1050 Disk Drive Field Service Manual (FD100330), 1050 parts list (Tandon), p. 5-11 (PDF p. 62).
- ↑ Best Electronics, "8-Bit Drives" catalogue page: Atari 1050 drive belts CB101140 (Tandon, Singapore) and CB101149 (World Storage, Hong Kong), complete Tandon mechanism CB101147. Retrieved 25 October 2026.
- ↑ 8.0 8.1 8.2 8.3 8.4 8.5 Atari, 1050 Disk Drive Field Service Manual (FD100330), schematic sheet 3 of 4 (Tandon), p. 5-4 (PDF p. 65; redrawn copy PDF p. 70): U5, VR2, Q4, Q6, R63, R69, R79, R80, L6, J1, J12, J14 and U6.
- ↑ 9.0 9.1 9.2 9.3 9.4 Atari, 1050 Disk Drive Field Service Manual (FD100330), p. 4-9 (PDF p. 51), tach feedback signals and speed adjust: U5 pins 11, 5, 9 and 10.
- ↑ 10.0 10.1 10.2 10.3 10.4 Howard W. Sams & Co., Computerfacts CD13 (1987), Preliminary Service Checks (PDF pp. 18-19): 10 V at pin 1 of P1, pressure cone tabs, "drive motor does not turn disk" checks starting with the belt, belt slipping, and VR2 set for 300 rpm.
- ↑ 11.0 11.1 11.2 11.3 11.4 Howard W. Sams & Co., Computerfacts CD13 (1987), p. 6, Troubleshooting, "Disk drive inoperative" (motor 11 ohms across P1 pins 1 and 2, tachometer 186 ohms across pins 3 and 4, U7 pin 11 at 3.2 V stopped and 0.1 V running).
- ↑ Atari, 1050 Disk Drive Field Service Manual (FD100330), p. 4-11 (PDF p. 53), diskette enable signal at U6 pins 10, 12 and 8.
- ↑ Howard W. Sams & Co., Computerfacts CD13 (1987), p. 11, schematic notes: readings taken with an Atari 800 running a BASIC program that writes a file to the drive repeatedly.
- ↑ Igor Gramblicka, "ATARI 1050, ATARI XF551 - napájací zdroj, Power Supply ATARI 1050, ATARI XF551 - modification", Igi blog, updated 19 January 2014 and 29 June 2015 (in Slovak). The drive's large heatsink cools the spindle motor's power transistor as well as the regulators.