PowerBook Duo 210 Trackball Repair

The PowerBook Duo 210 and the other 68k Duos, the PowerBook Duo 230, PowerBook Duo 250, PowerBook Duo 270c, PowerBook Duo 280 and 280c, have a 19 mm trackball with two buttons, connected to the logic board as an Apple Desktop Bus device. It is a separate assembly held to the chassis by two screws, and Apple's PowerBook 200 Series Service Source gives one procedure for all six models.[1][2] MacDat reports that earlier trackball boards carry one leaky surface-mount electrolytic, 10 µF 6.3 V, in a case that looks like a tantalum, while later boards have a 22 µF 10 V tantalum instead.[3] This repair covers removing the trackball assembly, replacing that capacitor where it is fitted, and refitting the assembly with its cables routed as Apple specifies.
Symptoms
[edit | edit source]Apple's symptom charts give these cures, in order:[4]
- Cursor does not move: reset the computer with Command-Control-Power On; clean the ball and rollers; make sure the display switch cable and battery cable are not fouling the trackball; check the logic board cable connections; replace the trackball; replace the logic board.
- Cursor moves erratically or only some of the time: clean the ball and rollers; replace the trackball; replace the logic board.
- Cursor moves but clicking the button does nothing: reset the computer; check the logic board cable connections; replace the trackball; replace the logic board.
The second cure on the first list, cables fouling the trackball, is a self-inflicted fault: Apple's reassembly note for the trackball is to route the display switch cable and the backup battery cable around it.[2] Other input faults are on PowerBook Duo Troubleshooting.
Safety
[edit | edit source]Disconnect the power adapter and remove the main battery before starting; Apple warns that skipping this can short the logic board. The boards are CMOS and easily damaged by static: wear an earthed wrist strap.[5]
Tools and parts
[edit | edit source]- T-8 and T-10 Torx drivers, an IC extractor and a jeweller's flat-blade screwdriver.[5]
- For an early board: a 10 µF 6.3 V low-profile surface-mount electrolytic, the value MacDat lists.[3]
- A fine-tipped soldering iron, flux, solder wick and isopropyl alcohol. See Surface-Mount Rework.
- A replacement assembly, if needed, was Apple service part 661-1654.[6]
Procedure
[edit | edit source]Opening the computer
[edit | edit source]- Disconnect the power adapter, slide open the battery door and pull out the main battery.[5]
- Close and latch the computer, turn it over and remove the four case screws. Turn it upright, open it, lift the keyboard out onto the palm rest, push out the release tabs and disconnect the two keyboard cables.[5]
- Push off the left and right end clutch covers.[5]
- Raise the bottom left corner of the top case to release the snap and slide the case off the four interlocking tabs along the front.[5]
Removing the trackball assembly
[edit | edit source]
- Lift the backup battery out of the trackball assembly and carefully disconnect its cable from the logic board.[5] The backup battery keeps the clock and control panel settings, so expect to reset them afterwards.[7]

- Remove the two self-threading screws that hold the trackball assembly to the chassis.[2]
- Disconnect the trackball cable with an IC extractor.[2]
- Lift out the trackball assembly.[2]
Cleaning and inspection
[edit | edit source]- Clean the ball and rollers, which is Apple's first cure for a cursor that sticks, jumps or will not move. Apple's Service Source does not describe taking the mechanism apart.[4]
- Look at the end of the board beside the button switch SW1. An early board has a black part printed "10" and "6.3V" there; a later board has a "22 10V" tantalum, which MacDat describes as the non-leaky part.[3]
- On an early board, look for electrolyte around the capacitor and on nearby tracks.[3] Clean any residue off with isopropyl alcohol; see Battery Explosion, Capacitor or Corrosion Damage and, for damaged tracks, PCB Trace Repair.
Replacing the capacitor
[edit | edit source]- Note the polarity marking of the old capacitor; in MacDat's photograph the + end faces the switch.[3]
- Remove the old part without lifting its pads and clean the pads.
- Solder in the new 10 µF 6.3 V part with the same polarity.[3]
Refitting
[edit | edit source]
- Set the trackball assembly in place, routing the display switch cable and the backup battery cable around the trackball.[2]
- Connect the trackball cable and refit the two self-threading screws. Back each screw off slightly before tightening it so that it follows its existing thread, and do not overtighten.[2][8]
- Connect the backup battery cable to the logic board and seat the backup battery in the trackball assembly.[5]
- Refit the top case, the end clutch covers and the keyboard. Do not overtighten the keyboard screws, which warps the keyboard and restricts the space bar; check every key afterwards.[5]
- Refit the main battery.[5]
Testing
[edit | edit source]- Roll the ball in every direction and check that the cursor follows smoothly, without sticking or jumping.[4]
- Click both trackball buttons; both should work.[1][4]
- Reset the date, time and control panel settings lost when the backup battery was disconnected.[7]
Related pages
[edit | edit source]- PowerBook Duo 210, PowerBook Duo 230, PowerBook Duo 250, PowerBook Duo 270c, PowerBook Duo 280
- PowerBook Duo Troubleshooting
- PowerBook Duo Capacitor Replacement Guide
- PowerBook Duo 210 Backup Battery Replacement
- PowerBook Duo 200 Series Service Source
References
[edit | edit source]- ↑ 1.0 1.1 Apple Computer, PowerBook 200 Series Service Source, Specifications, I/O Devices p. 8 (PDF p. 20): trackball, 19 mm diameter, dual button, Apple Desktop Bus (ADB) interface. Hosted as File:PowerBook Duo 200 Series Service Source.pdf; see PowerBook Duo 200 Series Service Source.
- ↑ 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Apple Computer, PowerBook 200 Series Service Source, Take Apart, Trackball pp. 22-25 (PDF pp. 96-99).
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 MacDat, "PowerBook Duo 210 Capacitor Reference", with the same trackball section on the 270c and 280c pages (retrieved 2026-10-25): earlier revisions of the Duo trackball have a single leaky "impostor tantalum" capacitor that is actually an electrolytic, 10 µF 6.3 V low-profile surface-mount; later revisions use a 22 µF 10 V tantalum; on the 280c page, "chances are that a 280c would be safe from this, but check just in case". Reference image by finkmac. Secondary source.
- ↑ 4.0 4.1 4.2 4.3 Apple Computer, PowerBook 200 Series Service Source, Troubleshooting, Symptom Charts/Peripherals pp. 28-30 (PDF pp. 56-58).
- ↑ 5.00 5.01 5.02 5.03 5.04 5.05 5.06 5.07 5.08 5.09 Apple Computer, PowerBook 200 Series Service Source, Take Apart: Main Battery p. 1, Keyboard pp. 2-7, End Clutch Covers pp. 8-9, Top Case pp. 10-13, Backup Battery pp. 19-21 (PDF pp. 75-95).
- ↑ Apple Computer, PowerBook 200 Series Service Source, Exploded View (PDF p. 266): trackball assembly 661-1654.
- ↑ 7.0 7.1 Apple Computer, PowerBook User's Guide for PowerBook Duo computers (1993), chapter 6, Power Management, pp. 93-96: the backup batteries keep the contents of memory for about 4 minutes while the main battery is changed, and keep other information, including control panel settings such as the clock, for up to 2 weeks. Archive.org item manualzz-id-1316791.
- ↑ Apple Computer, PowerBook 200 Series Service Source, Basics, Self-Threading Screws pp. 7-9 (PDF pp. 9-11): self-threading screws hold the hard drive, the trackball assembly, and the CPU stiffener and logic board; never overtighten them; back the screw off slightly before tightening.