Jump to content

Power Macintosh 5200 Display Adjustment

From RetroTechCollection
Power Macintosh 5200 display adjustment controls (Apple Service Source)
Apple's drawing of the display controls: VR301 to VR305 on the CRT video board, focus and screen on the flyback transformer, and VR601, VR701 and SW701 on the adjustment-controls board at the side of the chassis.

The Power Macintosh 5200 and its relatives have a built-in 15-inch colour display that is set up with trimmers on the CRT video board, two controls on the flyback transformer, a small adjustment-controls board at the side of the chassis, and software settings stored through a monitor adjustment cable. Apple's adjustments are light meter setup, geometry, video (cutoff and white balance) and high voltage.[1] The same chapter, with the same designators, is in Apple's manual for the Power Macintosh 5400 and 5500, which notes that the 5500 is built only from Rev. B parts.[2] Apple's Display Service Utility lists the four machines together, as "PowerPC 5200/5300/5400/5500".[1]

The procedure therefore covers the Power Macintosh 5300, Power Macintosh 5400 and Power Macintosh 5500, and the Performa versions of the Performa 5200, 5300 and 5400 series: the 5200CD, 5210CD, 5215CD, 5220CD, 5320CD, 5400CD, 5410CD, 5420CD, 5430 and 5440. The Power Macintosh 5260 and 5280 have a different analogue board, different controls and their own Service Source; see Power Macintosh 5260 Display Adjustment.

Symptoms

[edit | edit source]

Apple's first checklist for these machines warns that a misadjusted screen can look like a failed analogue board or CRT, so the adjustments come before any board is replaced. Jitter, faint lines or a moving picture can also come from nearby electrical equipment or fluorescent lights; move the machine to another room to rule that out.[3] The symptom charts send these faults to the adjustments below:[3]

  • Screen black, too dark or too bright with sound and drives working, after the front-panel contrast button, the Screen control panel and the yoke cable have been checked: video adjustments.
  • Screen bright with sound present but no picture: video adjustments.
  • Picture breaking into diagonal lines, or rolling: geometry adjustments.
  • Picture out of focus: focus, then a luminance check with cutoff and white balance.
  • Raster the wrong size: on-screen controls, to 185 mm (7.3 in) high and 240 mm (9.5 in) wide.
  • Raster tilted, shifted, distorted or off centre: move metal objects away, then the geometry and on-screen adjustments; use SW701 if the centring range runs out.

Two things are not faults. Some misconvergence is normal, especially at the edges of the screen, and some geometric distortion is within tolerance: Apple says the setting "need not be perfect".[3] A single line, poor linearity, or a colour tint that will not adjust are module faults in Apple's charts; see Macintosh Performa 5200CD Troubleshooting.

Safety

[edit | edit source]

Warning: the adjustments are made with the rear housing off and the display running. The flyback transformer, anode lead and analogue board carry high voltage, and the CRT holds its charge after the machine is unplugged. Apple's warnings for these machines:[1]

  • Use plastic adjustment tools only. Metal alignment tools are a shock hazard.
  • Make the adjustments from the rear and watch the screen in a mirror. Do not reach round the monitor to the controls.
  • Never wear an antistatic wrist strap until the CRT has been discharged, and take it off again before refitting the anode cap.

See CRT Discharge Procedure.

Tools and parts

[edit | edit source]
  • Display Service Utility, from the Utilities folder of Apple's MacTest Pro CD, for the test patterns and the on-screen controls.[1]
  • A small plastic Phillips-head tool and a small plastic flat-head tool; a fine-tip plastic tool for the video board trimmers.[1]
  • For white balance: Apple's R77 light meter (part 076-0310), or the older L-248 or 246, or a photometer.[1]
  • For the geometry settings: monitor adjustment cable 922-1513.[1]
  • For the high-voltage setting: a digital voltmeter.[1]
  • A mirror, and a CRT discharge tool if the anode cap is to come off.[1][4]

Procedure

[edit | edit source]

Before you start

[edit | edit source]
  1. Remove the two security screws from the I/O door, pull its two finger latches down and swing it up and off.[5]
  2. Prise off the two screw covers on each side of the rear housing, levering from their rear edge.[5]
  3. Remove the three Torx screws on each side of the rear housing, then slide the housing back and off. This exposes the high-voltage parts.[5]
  4. Identify the version, because the jumper, test point and high-voltage control differ. On a 5200 series machine the label on the lower rear of the case reads 620-0635 or 620-0835 on the original version (Rev. A) and 620-0637 or 620-0837 on Rev. B. On any of these machines, speakers built into the front bezel mean the original version and speakers fixed to the sides of the metal chassis mean Rev. B.[6] Every 5500 is Rev. B.[2]
  5. To see the speakers, take off the front bezel: disconnect the speaker cable (two grey round cables wrapped round a ferrite bead) and guide it down under the metal CRT frame, disconnect the microphone cable and guide it to the microphone side of the frame, then pull the bezel off.[5]
  6. Run the display for at least 10 minutes before the cutoff, white balance and high-voltage adjustments.[1]

Light meter setup

[edit | edit source]
  1. R77 meter: remove the 10× multiplier plate from the lens, set the scale switch to its bottom position (10–50 footcandles) and read only the bottom scale, with the lens against the middle of the screen. Its four-digit date stamp (for example 0398 for March 1998) gives its age; check a suspect meter against a known-good one.[1]
  2. L-248 meter: press the red button on the back and replace the battery if the needle is outside the red area; move the side switch up so the scale reads 10 to 18; uncover the lens, hold it against the middle of the screen and press the read button.[1]
  3. Model 246 meter: remove any metal slide from the top, fit the white lens with the red dot, turn the swivel head so the lens faces the screen and hold it against the middle of the screen.[1]

Horizontal and vertical shift

[edit | edit source]
  1. Run Display Service Utility and display the All-White Screen.[1]
  2. With a flat-blade plastic tool, turn the horizontal shift control VR701 until the raster is centred left to right.[1]
  3. If VR701 alone does not centre it, move the arm of the three-position horizontal centring switch SW701 with a plastic tool, and finish with VR701.[1]
  4. Turn the vertical shift control VR601 until the raster is centred top to bottom.[1]

Focus

[edit | edit source]
  1. Display the Focus test pattern.[1]
  2. With a flat-head plastic tool, turn the focus control on the flyback transformer for the sharpest pattern in the centre of the screen.[1]

Size, position, pincushion and trapezoid

[edit | edit source]

These are stored settings, changed with Display Service Utility once the monitor adjustment cable is fitted. The cable goes on a jumper on the analogue board, so the anode cap and rear EMI shield must come off first.[1]

Power Macintosh 5200 Rev. A analog board jumper P805 (Apple Service Source)
Jumper P805 on the Rev. A analogue board, near the logic board connector, and the cable run to the modem port.
Power Macintosh 5200 Rev. B analog board jumper P102 (Apple Service Source)
Jumper P102 on the Rev. B board. The inset shows the arrow on the cable's plug.
  1. Turn off virtual memory, then switch the computer off.[1]
  2. Discharge the CRT: take off your wrist strap, clip the discharge tool to the metal chassis, slide the probe under the anode cap until it touches the anode aperture, and remove the anode cap. Put the wrist strap back on.[4] See CRT Discharge Procedure.
  3. Disconnect the microphone cable. Remove the four screws from the rear EMI shield, swing the shield up and lift it off (the larger Rev. B shield comes off the same way). Remove the modem card if one is fitted.[1][5]
  4. Remove the three Phillips screws that hold the analogue board to the chassis and tilt the board back without straining its cables.[1]
  5. Find the jumper near the logic board connector at the lower left corner of the analogue board: P805 on Rev. A, P102 on Rev. B. Remove the shunt from its pins.[1]
  6. Rev. A: fit one end of monitor adjustment cable 922-1513 on P805 with the pin 1 opening over pin 1, which is marked by a square on the silkscreen.[1]
  7. Rev. B: fit the cable on the two pins of P102 with the gold contacts facing you and the arrow on the plug over the pin nearer the top of the board. Apple warns that the adjustment does not work if the plug is the wrong way round.[1]
  8. Plug the other end into the modem port; no other port works. Remove the internal modem and the plastic modem-port cover if they are fitted. Route the cable clear of sharp edges and leave it slack.[1]
  9. Refit the rear EMI shield and reconnect its grounding screw.[1]
  10. Take off the wrist strap and refit the anode cap.[1]
  11. Turn the machine so that you can see the screen, and switch on.[1]
Power Macintosh 5200 on-screen geometry controls (Apple Service Source)
The on-screen controls in Display Service Utility: horizontal size, position, pincushion and trapezoid, vertical size and position.
  1. Run Display Service Utility, choose "PowerPC 5200/5300/5400/5500" in the pattern selection box, then choose adjust geometry.[1]
  2. Use the scroll bars to set horizontal size, position, pincushion and trapezoid, and vertical size and position. Apple's target raster is 185 mm (7.3 in) high and 240 mm (9.5 in) wide.[1][3]
  3. Click Save to store the settings for the resolution shown, or Cancel to return to the last saved settings.[1]
  4. Set and save every resolution the utility offers in turn; the next one appears after each Save or Cancel. A resolution left unsaved looks misadjusted when the machine is switched to it. Quit the utility after the last one.[1]

Cutoff

[edit | edit source]

Do the cutoff before the white balance, and whenever the CRT or deflection board has been replaced or the screen control has been moved.[1]

  1. With a fine-tip plastic tool, turn the sub-contrast control VR301 on the CRT video board fully clockwise. The screen gets brighter.[1]
  2. Open the Screen control panel. Set Screen Brightness to minimum (far left) and Screen Contrast to maximum (far right).[1]
  3. Set the green gain VR303 and red gain VR302 to the middle of their travel.[1]
  4. Check the resolution is 640 × 480 and display the Gray Bars pattern.[1]
  5. Set the red bias VR304 and green bias VR305 fully anticlockwise.[1]
Power Macintosh 5200 screen control and gray bars pattern (Apple Service Source)
The screen control on the flyback transformer, set against the Gray Bars pattern.
  1. With a plastic screwdriver, turn the screen control on the flyback transformer very slowly until the third darkest bar from the left is just faintly visible. Apple says it should not need setting again unless it is disturbed.[1]

White balance

[edit | edit source]
  1. With the resolution at 640 × 480, display the Gray Bars pattern.[1]
  2. Adjust the red bias VR304 and green bias VR305 until the four darkest bars are neutral grey. If they look blue, start with the green bias until it is hard to tell blue from green, then set the red bias until they are shades of grey.[1]
  3. If the bars stay too red or too green, turn both bias controls down together. The darkest bar must stay completely black and the second darkest must be just visible.[1]
  4. In the Screen control panel, set Screen Brightness to its centre position. The screen may look too bright and soft at this point.[1]
  5. Display the All-White Screen and hold the light meter or photometer against the centre of the screen.[1]
  6. Turn the sub-contrast control VR301 down until the meter reads 21 on the bottom scale of an R77, the upper end of 10 on the 10–18 scale of an L-248, 21 footcandles on the red scale of a model 246, or 25 foot-lamberts on a photometer.[1]
  7. Display the Gray Bars pattern. The four brightest bars should be shades of grey and the leftmost bar solid black. If they are tinted, adjust the red gain VR302 and green gain VR303 until they are neutral.[1]
  8. Check the luminance again on the All-White Screen and reset VR301 to the reading above if it has moved.[1]

High voltage

[edit | edit source]

Apple requires this adjustment whenever the CRT or the deflection board is replaced. Remove the rear housing and the rear EMI shield, then reattach the ground wire and its screw, and run the display for 10 minutes first.[1]

Power Macintosh 5200 high voltage test point Rev. A (Apple Service Source)
Rev. A analogue board: meter between the cathode of D713 and chassis ground.
Power Macintosh 5200 high voltage test point Rev. B (Apple Service Source)
Rev. B analogue board: meter between the cathode of D703 and chassis ground.
  1. Display the Crosshatch pattern.[1]
  2. Connect the digital voltmeter's red lead to the cathode side of diode D713 (Rev. A) or D703 (Rev. B), and its black lead to the metal chassis.[1]
  3. With a fine-tip plastic tool, set the high-voltage control so that the meter reads 29.5 V DC ± 0.1 V. On Rev. A it is VR501, inside the analogue board. On Rev. B it is VR702, also inside the board; tilt the board back to reach it.[1]
Power Macintosh 5200 Rev. B analog board VR702 (Apple Service Source)
VR702 on the Rev. B analogue board, reached with the board tilted back.

Reassembly

[edit | edit source]

Apple gives no closing steps for the on-screen adjustment. To put the machine back to normal, reverse the opening steps: switch off, discharge the CRT and remove the anode cap, take off the rear EMI shield, unplug the monitor adjustment cable and refit the shunt over the pins of P805 or P102, refit the analogue board's three screws, the EMI shield, the microphone cable and the anode cap.[1][4]

  1. Refit the front bezel if it was removed, guiding the microphone cables through the plastic retainers and the speaker cable behind the metal CRT frame and up to its connector.[5]
  2. Slide the rear housing on, fit the three Torx screws each side and press the screw covers back in.[5]
  3. Slide the I/O door's hinge tabs up into position and swing the door down until it snaps shut.[5]

Testing

[edit | edit source]
  • On the All-White Screen the raster should be centred and measure 240 mm (9.5 in) wide by 185 mm (7.3 in) high.[3]
  • On the Gray Bars pattern the leftmost bar should be solid black, the next just visible, and the brighter bars neutral grey.[1]
  • Screen luminance should read the meter values given under White balance, for example 25 foot-lamberts on a photometer.[1]
  • After a CRT or deflection board change, the high-voltage test point should read 29.5 V ± 0.1 V.[1]

If the picture still cannot be brought into range, Apple's next step for most of these symptoms is a new analogue/video board.[3]

Revision notes

[edit | edit source]
Designators that differ between versions[1]
Item Original version (Rev. A) Rev. B
Monitor adjustment cable jumper P805 (pin 1 marked by a square) P102 (arrow on plug towards top of board)
High-voltage test point Cathode of D713 Cathode of D703
High-voltage control VR501, inside the board VR702, inside the board; tilt the board back

The analogue/video board assemblies of the two versions are not interchangeable, and the 5500 uses only Rev. B parts.[7][2] The adjustment chapter of the 5400 and 5500 manual is the same, page for page.[2]

[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.44 1.45 1.46 1.47 1.48 1.49 1.50 1.51 1.52 1.53 1.54 1.55 1.56 1.57 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300 (not 5260, 5280) (1997), Adjustments chapter: Light Meter Setup pp. 1–6, Geometry pp. 7–23, Video pp. 24–38, High Voltage pp. 39–43 (PDF pp. 275–317). Hosted as File:Powermac.perf_5200.5300.pdf; see Power Macintosh/Performa 5200 and 5300 Service Source.
  2. ↑ 2.0 2.1 2.2 2.3 Apple Computer, Service Source: Power Macintosh/Performa 5000 Series (5400 and 5500, 1997), Adjustments chapter pp. 1–43 (PDF pp. 263–305), and Basics, Rev. B p. 2 (PDF p. 4). Hosted as File:Powermac.perf_5400.5500.pdf; see Power Macintosh/Performa 5000 Series Service Source.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Troubleshooting chapter: First Checklist p. 2 and Symptom Charts/Video pp. 11–17 (PDF pp. 52, 61–67). Hosted as File:Powermac.perf_5200.5300.pdf.
  4. ↑ 4.0 4.1 4.2 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, REA Procedures chapter, Repair Procedures pp. 36–37, steps 40–44 (PDF pp. 260–261): discharging the CRT.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Take Apart chapter: I/O Door pp. 17–19, Rear Housing pp. 26–29, Front Bezel pp. 30–33, Rear EMI Shield pp. 36–39 (PDF pp. 100–122).
  6. ↑ Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Basics chapter, Rev. B, 5000 Series pp. 2–3 (PDF pp. 4–5).
  7. ↑ Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Take Apart chapter, Video Board p. 73 and Analog Board, Original Version p. 80 (PDF pp. 156, 163).