Power Macintosh 5260 Display Adjustment

The Power Macintosh 5260 has a built-in 14-inch colour display whose geometry, convergence, colour balance and brightness are set with trimmers on the analogue board, the CRT yoke and the flyback transformer, and its power supply board has one adjustment, R828. Apple's adjustments for the machine are light meter setup, geometry, video and power supply.[1] The same manual covers the Power Macintosh 5260/100 and 5260/120 and the international Performa 5260/120 and Performa 5280. Low End Mac treats the 100 MHz Performa 5260CD as the 5260/100, and Apple's specification page for the Performa 5270CD gives the same 100 MHz PowerPC 603e and built-in 14-inch monitor.[2][3][4]
The controls and procedure are different from those of the 5200, 5300, 5400 and 5500, which are in Power Macintosh 5200 Display Adjustment. The 5260 has no monitor adjustment cable procedure and no high-voltage adjustment in its manual; it has its own size, keystone and convergence trimmers instead.[1]
Symptoms
[edit | edit source]Apple's first checklist warns that a misadjusted screen can mimic a failed analogue board or CRT, and that jitter, faint lines or a moving picture can come from nearby electrical equipment or fluorescent lights; move the machine to another room to rule that out.[5] The symptom charts send these faults to the adjustments:[5]
- Screen black, too dark or too bright with sound and drives working, after the front-bezel contrast button, the Screen control panel and the yoke cable have been checked: video adjustments.
- Screen bright with sound present but no picture: video adjustments.
- Picture breaking into diagonal lines, or rolling vertically or horizontally: geometry adjustments.
- Out of focus: focus, then a luminance check with the cutoff and white-balance procedure.
- Raster tilted, shifted, barrel-shaped or not square: move metal objects away, then the geometry adjustments.
- Raster not centred: the horizontal or vertical shift control.
Some misconvergence is normal, especially at the edges of the screen, and some geometric distortion is within tolerance; Apple says the setting "need not be perfect".[5] White areas with blotches of colour are a purity problem that magnetic fields can cause: move the machine and degauss it with a manual degaussing coil.[5] A single line or poor linearity is an analogue/video board or CRT fault in Apple's charts; see Power Macintosh 5260 Troubleshooting.
Safety
[edit | edit source]Warning: the adjustments are made with the rear housing off and the machine running. The flyback transformer, anode lead, analogue board and power supply board carry high voltage, and the CRT holds its charge after the machine is unplugged.[1] Use plastic adjustment tools only: Apple warns that metal alignment tools are a shock hazard.[1] See CRT Discharge Procedure.
Tools and parts
[edit | edit source]- Display Service Utility, from the Utilities folder of the MacTest Pro CD, for the All-White Screen, Focus, Crosshatch 1 and Gray Bars test patterns.[1]
- A small plastic Phillips-head tool and a small plastic flat-head tool, and a fine-tip plastic tool for the convergence, distortion and video controls.[1]
- For brightness: Apple's R77 light meter (part 076-0310), the older L-248 or 246, or a photometer.[1]
- A ruler for the raster size, and a DC voltmeter for the power-supply adjustment.[1]
Procedure
[edit | edit source]Before you start
[edit | edit source]- Remove the two security screws from the I/O door, pull its two finger latches down and swing it up and off.[6]
- Prise off the two screw covers on each side of the rear housing, levering up from the rear edge.[6]
- Remove the three Torx screws on each side and slide the rear housing back and off. This exposes the high-voltage parts.[6]
- For the cutoff and white-balance steps, run the display for at least 10 minutes first.[1]
Light meter setup
[edit | edit source]- R77: remove the 10× multiplier plate from the lens, set the scale switch to its bottom position (10–50 footcandles) and read only the bottom scale, with the lens against the middle of the screen. Its four-digit date stamp (for example 0398 for March 1998) shows its age; check a suspect meter against a known-good one.[1]
- L-248: press the red button on the back and replace the battery if the needle is outside the red area; move the side switch to its lower position so the scale reads 2 to 10; uncover the lens, hold it against the middle of the screen and press the read button.[1]
- Model 246: remove any metal slide from the top, fit the white lens with the red dot, turn the swivel head so the lens faces the screen and hold it against the middle of the screen.[1]
Shift
[edit | edit source]- Run Display Service Utility and display the All-White Screen.[1]
- With a flat-blade plastic tool, turn the horizontal shift control R410 until the raster is centred left to right.[1]
- Turn the vertical shift control R320 until the raster is centred top to bottom.[1]
Size
[edit | edit source]
- With the All-White Screen displayed, turn the Horizontal Size 2 control R440 until the raster is 240 mm ± 2 mm (9.5 in ± 1/8 in) wide.[1]

- Turn the Vertical Size 1 control R327 until the raster is 185 mm ± 2 mm (7.3 in ± 1/8 in) high.[1]
Focus
[edit | edit source]- Display the Focus test pattern.[1]
- With a flat-head plastic tool, turn the focus control on the flyback transformer for the best focus in the centre of the screen.[1]
Convergence
[edit | edit source]
- Display the Crosshatch 1 test pattern.[1]
- With a fine-tip plastic tool, set the Yv control (yoke-mounted vertical dynamic convergence) for the best convergence of the vertical lines at the top and bottom of the screen.[1]
- Set the Yhc control (yoke-mounted horizontal dynamic convergence) for the best convergence of the horizontal lines at the top and bottom of the screen.[1]
Pincushion and keystone
[edit | edit source]
- With the Crosshatch 1 pattern displayed, adjust the Pincushion (E/W 2) control if the raster is barrel-shaped.[1]
- Adjust the Keystone control R438 if the raster is narrower or wider at the top than at the bottom.[1]
Cutoff and white balance
[edit | edit source]Apple's note for this procedure is to perform it when the CRT or analogue board is replaced, or if the screen control has been moved.[1]
- Open the Screen control panel. Set Screen Brightness to its midpoint and Screen Contrast to maximum (far right).[1]
- Display the Gray Bars test pattern.[1]

- With a fine-tip plastic tool, set these controls to their midpoints: green bias R940, red bias R910, blue bias R970, blue drive R561, green drive R531, red drive R501 and sub-brightness R500. The drive and sub-brightness controls are inside the analogue board.[1]

- Set R437 to its midpoint.[1]
- Display the Gray Bars pattern again. Turn the screen control on the flyback transformer very slowly until the first bar (furthest left) is solid black and the bar next to it is very dark.[1]
- In the Screen control panel, set Screen Contrast to its midpoint, and display the Gray Bars pattern.[1]
- Keeping the leftmost bar solid black, adjust the red and green bias controls to make the darkest bars neutral grey. If the screen looks blue, adjust the green bias R940 until the blue is neutralised, then the red bias R910 until the bars are shades of grey.[1]
- Set Screen Contrast back to maximum and display the Gray Bars pattern. The screen may now look too bright and soft.[1]
- If the screen looks blue, adjust the green drive R531 until the blue is neutralised, then the red drive R501 until the bars are shades of grey.[1]
- Display the All-White Screen and hold the light meter or photometer against the centre of the screen.[1]
- Turn the sub-brightness control R500 down until the meter reads 20 ± 3 on the bottom scale of an R77, 20 ± 3 footcandles on the red scale of a model 246, 25 foot-lamberts on a photometer, or between 9 and 10 on an L-248.[1]
Power supply
[edit | edit source]Apple requires this adjustment whenever the analogue board or the power supply is taken out.[1]

- Connect the DC voltmeter's ground lead to the metal chassis.[1]
- Connect the other lead to pin 3 of connector P805 on the power supply. Apple's drawing marks pin 1 of P805 to help find it.[1]

- With the machine running, adjust R828 until the meter reads 110 V DC.[1]
Reassembly
[edit | edit source]- Slide the rear housing back on, refit the three Torx screws on each side and press the screw covers back in.[6]
- Align the I/O door's hinge tabs, slide it up into position and swing it down until it snaps closed.[6]
Testing
[edit | edit source]- On the All-White Screen the raster should be centred, 240 mm ± 2 mm wide and 185 mm ± 2 mm high.[1]
- On the Gray Bars pattern the leftmost bar should be solid black and the bars neutral grey; the white screen should read the luminance given above.[1]
- P805 pin 3 should read 110 V DC to chassis after a power supply or analogue board has been refitted.[1]
If a fault cannot be adjusted out, Apple's next step in most of the video charts is a new analogue/video board assembly, and after that the CRT.[5]
Revision notes
[edit | edit source]- Apple's 5260 symptom chart for a colour tint that will not adjust lists checking the video board on the CRT socket and the cables, replacing the RGB cable, then replacing the analogue/video board assembly and performing the video adjustments.[5] The Repair Extension Program cable replacement described in Power Macintosh 5200 Internal RGB Cable Replacement was for the 5200 and 5300 and excluded the 5260 and 5280.[7]
Related pages
[edit | edit source]- Power Macintosh 5260, Macintosh Performa 5260, Macintosh Performa 5260CD, Macintosh Performa 5270CD, Macintosh Performa 5280
- Power Macintosh 5260 Troubleshooting
- Power Macintosh 5260 General Maintenance
- Power Macintosh 5260 Capacitor Replacement Guide
- Power Macintosh 5200 Display Adjustment
- Power Macintosh/Performa 5260, 5280 Series Service Source
- CRT Discharge Procedure
References
[edit | edit source]- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 Apple Computer, Service Source: Power Macintosh/Performa 5260, 5280 Series (1997), Adjustments chapter: Light Meter Setup pp. 1–6, Geometry pp. 7–17, Video pp. 18–29 and Power Supply pp. 30–31 (PDF pp. 184–214). Hosted as File:Powermac.perf_5260.5280.pdf; see Power Macintosh/Performa 5260, 5280 Series Service Source.
- ↑ Low End Mac, "Performa 5260", LEM Staff, accessed 2026-10-25: 5260/100 introduced 15 April 1996, 800 MB hard drive on the 5260CD.
- ↑ Apple Computer, Service Source: Power Macintosh/Performa 5260, 5280 Series, title page and Basics chapter, 5260/120 and 5280 p. 2 (PDF pp. 1 and 4).
- ↑ Apple, "Macintosh Performa 5270CD: Technical Specifications", accessed 2026-10-25.
- ↑ 5.0 5.1 5.2 5.3 5.4 5.5 Apple Computer, Service Source: Power Macintosh/Performa 5260, 5280 Series, Troubleshooting chapter: First Checklist p. 2 and Symptom Charts/Video pp. 8–14 (PDF pp. 47, 53–59).
- ↑ 6.0 6.1 6.2 6.3 6.4 Apple Computer, Service Source: Power Macintosh/Performa 5260, 5280 Series, Take Apart chapter: I/O Door pp. 17–19 and Rear Housing pp. 26–29 (PDF pp. 91–93, 100–103).
- ↑ Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300 (not 5260, 5280) (1997), REA Procedures chapter, Repair Overview for Freezing and Video Color Hue Issues p. 1 (PDF p. 225). Hosted as File:Powermac.perf_5200.5300.pdf.