Jump to content

Power Macintosh 5200 Internal RGB Cable Replacement

From RetroTechCollection
Power Macintosh 5200 internal RGB cable P703 to P301 (Apple Service Source)
The internal RGB cable on a Rev. A machine, from P703 on the analogue board to P301 on the CRT video board, with its two ferrite beads.

The internal RGB cable in the Power Macintosh 5200 carries the colour signals from the analogue board (connector P703) to the video board on the neck of the CRT (connector P301).[1] Apple's Repair Extension Program for the Power Macintosh and Performa 52xx and 53xx (not the 5260 and 5280) replaced this cable to cure "sudden or intermittent changes in the monitor's color hue", and Apple's symptom charts list it as a cure on the original version (Rev. A) of the analogue/video board only.[1][2] Apple limits the replacement to Rev. A units. On the Rev. B board P703 and P301 are a 10-pin power-supply cable and a 10-pin ribbon cable, and the Power Macintosh 5500 was built only from Rev. B parts.[3][4]

The same cable and the same chart entry appear in Apple's manual for the Power Macintosh 5400.[4] The procedure applies to Rev. A examples of the Power Macintosh 5300 and the Performa versions: the Performa 5200CD, 5210CD, 5215CD, 5220CD, 5300CD and 5320CD.

Symptoms

[edit | edit source]
  • The colour hue of the whole screen changes suddenly or comes and goes.[1]
  • A predominant colour tint that cannot be adjusted out. Apple's cures for that symptom, in order, are: check that the video board is pushed fully onto the CRT socket, check the cable connections to the analogue/video board, replace the internal RGB cable on a Rev. A board, then replace the analogue/video board assembly and perform the video adjustments, and last the CRT.[2]

Rule out the simpler causes first. A tint that stays the same and can be balanced out is a white-balance setting; see Power Macintosh 5200 Display Adjustment. White areas with blotches of colour are magnetisation, cured by moving the machine and degaussing it.[2] See also Macintosh Performa 5200CD Troubleshooting.

Check the machine's history before opening it. Apple's technicians fixed a "VID" label (922-2395), or wrote "VID" by hand, above the FCC ID number on the back of every unit whose internal RGB cable they had inspected or replaced.[1] A replacement cable can be recognised inside the machine by white tape between its two ferrite beads; if that tape is there, Apple's instruction is to leave the cable alone.[1]

Safety

[edit | edit source]

Warning: this job is done with the rear housing off, next to the flyback transformer, the anode lead and the CRT. The CRT holds a high-voltage charge after the machine is unplugged and must be discharged before the anode cap comes off.[1] Never discharge the CRT while wearing a grounding wrist strap; take the strap off before discharging and before refitting the anode cap.[1] See CRT Discharge Procedure.

Tools and parts

[edit | edit source]
  • Internal RGB cable, Apple part 922-2357.[1]
  • Torx driver for the rear housing screws and a Phillips screwdriver for the rear EMI shield and the analogue board mounting screws.[3][1]
  • CRT discharge tool and a grounding wrist strap.[1]
  • A blade to cut any adhesive between the video board and the CRT.[1]

Procedure

[edit | edit source]

Opening the machine

[edit | edit source]
  1. Switch off, disconnect the power cord and all external cables, and note where they went.[1]
  2. Remove the two screws from the I/O door, release its two latches with your fingertips and swing it up and off.[1]
  3. Prise off the two screw covers on each side of the rear housing, levering up from the rear edge of each cover.[1]
  4. Remove the three Torx screws on each side of the rear housing and slide the housing back and off.[1]
  5. Look at the internal RGB cable between P703 on the analogue board and P301 on the video board. If it has white tape between the two ferrite beads it is a replacement cable; stop here and go to Testing.[1]
  6. Remove the four screws from the rear EMI shield, swing the shield up and lift it off.[1]

Discharging the CRT

[edit | edit source]
  1. Take off your grounding wrist strap.[1]
  2. Clip the CRT discharge tool to the metal chassis, slide the probe under the anode cap until it touches the anode aperture, and remove the anode cap.[1]
  3. Put the wrist strap back on.[1]

Reaching the cable

[edit | edit source]
Power Macintosh 5200 video board pulled off the CRT (Apple Service Source)
The two long grounding cables on the video board, and the video board coming off the CRT neck.
  1. Remove the two long grounding cables from the video board.[1]
  2. If adhesive holds the video board to the CRT, cut and peel it off.[1]
  3. Pull the video board gently off the CRT. It only needs to come off the neck; it stays in the machine.[1]
  4. Remove the three analogue board mounting screws. Their positions vary slightly between units.[1]
Power Macintosh 5200 analog board and shield tilted back (Apple Service Source)
Lifting the analogue board and shield out of the CRT frame channel. The inset shows the chassis tab and slot that hold the shield.
  1. Lift the end of the analogue board that faces the back of the machine and free the analogue board shield from the chassis tabs and slot.[1]
  2. Lift the analogue board and shield out of the CRT frame channel and tilt them away from the CRT. They stay connected; they only need to move far enough to reach the cable.[1]

Replacing the cable

[edit | edit source]
  1. Disconnect the internal RGB cable at P703 on the analogue board and at P301 on the video board. If either ferrite bead is glued to the chassis, prise it up.[1][3]
  2. Fit the replacement cable to P703 and P301.[1]

Reassembly

[edit | edit source]
  1. Lower the analogue board and shield back into place, with the bottom edge of the board and shield sitting in the CRT frame channel, and refit the three mounting screws.[1]
  2. Push the video board back onto the CRT until it is fully seated against the CRT, and refit its two grounding cables.[1]
  3. Refit the rear EMI shield: insert its two corner hinge tabs into the slots in the power supply and analogue board shields, swing it down and refit the four screws.[1][3]
  4. Take off the wrist strap and refit the anode cap.[1]
  5. Slide the rear housing on, fit the three Torx screws on each side and press the screw covers back in. Refit the I/O door: align its hinge tabs, slide it up and swing it down until it snaps shut.[3]

Testing

[edit | edit source]
  • Reconnect the cables, switch on and check that the machine starts up and that the colour of the display is correct.[1]
  • If the screen still shows a consistent colour hue after the new cable is in, Apple's next step is to replace the analogue board.[1] A board that has been replaced needs the video adjustments; see Power Macintosh 5200 Display Adjustment.[2]
  • Apple's labelling after this repair is the VID label (922-2395) above the FCC ID number; it marks the unit for anyone who services it later.[1]

Revision notes

[edit | edit source]
  • Rev. A and Rev. B are identified by the speakers (in the front bezel on Rev. A, on the sides of the metal chassis on Rev. B) or, on 5200-series machines, by the part number on the label at the lower rear of the case: 620-0635 or 620-0835 for Rev. A, 620-0637 or 620-0837 for Rev. B.[5]
  • The Rev. A and Rev. B analogue/video board assemblies are not interchangeable.[3]
  • The same Repair Extension Program also covered system freezes on these machines; see Power Macintosh 5200 Cache/ROM DIMM Replacement.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300 (not 5260, 5280) (1997), REA Procedures chapter: Repair Overview for Freezing and Video Color Hue Issues pp. 1–6, Part Numbers pp. 10–11 and Repair Procedures pp. 30–46, steps 33–59 (PDF pp. 225–230, 234–235 and 254–270). Hosted as File:Powermac.perf_5200.5300.pdf; see Power Macintosh/Performa 5200 and 5300 Service Source.
  2. ↑ 2.0 2.1 2.2 2.3 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Troubleshooting chapter: First Checklist p. 2 and Symptom Charts/Video pp. 12 and 17 (PDF pp. 52, 62, 67).
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Take Apart chapter: I/O Door pp. 17–19, Rear Housing pp. 26–29, Rear EMI Shield pp. 36–39, Video Board pp. 71–74, Analog Board, Rev. B pp. 86–89 and Internal RGB Cable pp. 90–91 (PDF pp. 100–122, 154–157, 169–174).
  4. ↑ 4.0 4.1 Apple Computer, Service Source: Power Macintosh/Performa 5000 Series (5400 and 5500, 1997), Basics, Rev. B p. 2; Troubleshooting, Symptom Charts/Video; Take Apart, Internal RGB Cable pp. 94–95 (PDF pp. 4, 77, 192–193). Hosted as File:Powermac.perf_5400.5500.pdf; see Power Macintosh/Performa 5000 Series Service Source.
  5. ↑ Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Basics chapter, Rev. B, 5000 Series pp. 2–3 (PDF pp. 4–5).